What command would you enter to restore the /vol/flexvol0/etc/rc file from a snapshot to the /vol/flexvol0/home directory?

snap restore -t file -r /vol/flexvol0/home/rc /vol/flexvol0/etc/rc

snap restore -r vol /vol/flexvol0/home/rc /vol/flexvol0/etc/rc

snap restore -t /vol/flexvol0/home/rc /vol/flexvol0/etc/rc

snap restore -t file -r /vol/flexvol0/home/rc /vol/flexvol0/etc/rc

snap restore -s /vol/flexvol0/home/rc /vol/flexvol0/etc/rc

Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?

The destination and source contain disks of the same size.

The destination and source contain RAID groups of the same size.

The destination and source contain the same number of RAID groups.

The destination and source contain disks of the same size.

The destination and source contain RAID groups of the same size.

The destination and source storage appliances are no further than 30 meters apart.

The destination and source contain the same number of RAID groups.

What is the format for snapvault schedule?

List of dates in ISO Date format

Which one of the following statements apply to the Free Space Estimator utility?

This utility determines if there is sufficient disk space available on the primary to perform an OSSV transfer

This utility determines if there is sufficient space on the secondary volume to perform a transfer

This utility determines if there is sufficient disk space available on the primary to perform an OSSV transfer

This utility run automatically after each transfer

This utility must be enabled on the secondary storage system

Which two supported methods would you use to restore data from a SnapVault for Net Backup Volume?

Use the Net Backup Administration Console

Use the snapvault restore Data ONTAP command

Use the SnapRestore Data ONTAP service

Which one of the following is not a pre-requisite for using SnapRestore?

The volume to be reverted must be offline.

You must enter the SnapRestore license code before you can use it.

Snapshots must exist on the storage appliance so that you can select a snapshot for the reversion.

The volume to be reverted must be offline.

The volume to be reverted must not be a SnapMirror destination.

In a Fabric Attached Metro Cluster, disk ownership by a node is determined by_____________.

where the FC HBAs for disks connect into the switch, and by where the disks connect to the switch banks.

the types of disks used in the cluster.

the slots in which the FC HBA is installed.

Which one of the following statements is not true when using SnapRestore?

The options snaprestore <vol_path_name> enable on option must be enabled.

SnapRestore must be licensed before you can use it.

The options snaprestore <vol_path_name> enable on option must be enabled.

The volume to be reverted must not be a SnapMirror destination mirror.

What is the format for snapvault schedule?

List of dates in ISO Date format

Which one of the following statements is not true when using SnapRestore?

The options snaprestore <vol_path_name> enable on option must be enabled.

SnapRestore must be licensed before you can use it.

The options snaprestore <vol_path_name> enable on option must be enabled.

The volume to be reverted must not be a SnapMirror destination mirror.

Which one of the following actions will cause a currently in sync snapmirror relationship to fall out of sync?

Modifying the /etc/snapmirror.conf file on the destination storage appliance

Modifying the /etc/snapmirror.conf file on the source storage appliance

Modifying the /etc/snapmirror.conf file on the destination storage appliance

Running snapmirror update on the source storage appliance

Running snapmirror release on the source storage appliance

To restore a primary SnapVault qtree to the exact qtree location on the primary storage system (from which it was backed up), you must:

Restore to a non-existing qtree

Add the new qtree to the primary storage system

Restore to a non-existing qtree

Overwrite the existing qtree on the primary storage system

Delete the existing qtree from the secondary storage system

Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?

The destination and source contain disks of the same size.

The destination and source contain RAID groups of the same size.

The destination and source contain the same number of RAID groups.

The destination and source contain disks of the same size.

The destination and source contain RAID groups of the same size.

The destination and source storage appliances are no further than 30 meters apart.

The destination and source contain the same number of RAID groups.

Alter issuing the vol split vol0/plex0 volNew command:

There are two unmirrored volumes, vol0 and volNew.

There are two new plexes, plex0 and plexNew.

There is a new mirrored volume called volNew.

There is a new plex called plexNew.

Which one of the following statements is true of storage appliance SnapVault backup?

The qtree is the basic unit for SnapVault backup.

The volume is the basic unit of SnapVault backup.

The file is the basic unit for SnapVault backup.

The directory is the basic unit for SnapVault backup.

The qtree is the basic unit for SnapVault backup.

When using MetroCluster, identify two methods for restricting access to the disaster site node. (Choose 2)

Turn off power to the disaster site node.

Use the cf forcetakeover-d command.

Which two supported methods would you use to restore data from a SnapVault for NetBackup Volume?

Use the NetBackup Administration Console

Use the snapvault restore Data ONTAP command

Use the SnapRestore Data ONTAP service

The snapvault snap sched-x command can be used to:

Specify platforms that can be backed up

When you are setting up SnapMirror, which one of the following is not a replication pre-requisite?

The source volume must be offline.

SnapMirror must be licensed for each storage appliance.

The source volume must be offline.

If you are replicating a volume, you must create a restricted volume to be used as the SnapMirror destination volume.

The capacity of the SnapMirror destination must be greater than or equal to the capacity of the source.

Which three are true when creating a SyncMirror volume? (Choose 3)

The number of disks added must be an even number and equally divided between the two plexes.

The number of disks selected for one plex must equal the number of disks selected from the other plex.

The disks are selected first on the basis of equivalent bytes per sector (bps) size, then on the basis of the size of the disk. If there is no equivalent-sized disk, Data ONTAP takes a larger capacity disk and downsizes it.

The number of disks added must be an even number and equally divided between the two plexes.

The disks selected for Plex 0 and Plex 1 must come from the same disk pools.

The number of disks selected for one plex must equal the number of disks selected from the other plex.

The disks are selected first on the basis of equivalent bytes per sector (bps) size, then on the basis of the size of the disk. If there is no equivalent-sized disk, Data ONTAP takes a larger capacity disk and downsizes it.

You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which one of the following is the most likely explanation?

You must recreate the directory structure before trying to restore the file.

Once the directory structure has been deleted, you cannot restore the file using single file SnapRestore. You must now SnapRestore the volume.

Snapshots have been created since the original directory structure was deleted.

Which one of the following actions will cause a currently in sync snapmirror relationship to fall out of sync?

Modifying the /etc/snapmirror.conf file on the destination storage appliance

Modifying the /etc/snapmirror.conf file on the source storage appliance

Modifying the /etc/snapmirror.conf file on the destination storage appliance

Running snapmirror update on the source storage appliance

Running snapmirror release on the source storage appliance

Network Appliance NS0-163 Practice Test 1 - Free Online Exam Questions 1-40

A volume can contain up to___snapshots concurrently.

125

225

255

Depends on capacity and number of disk drives

Comment (0)

Network Appliance NS0-163 Practice Test 1

Question

Drag and Drop

Hot Area

Network Appliance NS0-163 Practice Tests

Practice Tests