Home / Fortinet / NSE6_FSW-7.2

Fortinet NSE6_FSW-7.2 Practice Test - Questions Answers, Page 5

Question list

List of questions

Question 41

(0)

FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?

Question 42

(0)

Refer to the exhibit. The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration

Question 43

(0)

What can an administrator do to maintain the existing standalone FortlSwltch configuration while changing the management mode to FortLink?

Question 44

(0)

Exhibit. Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

Question 45

(0)

Exhibit. Which configuration change will allow the managed FortiSwitch to accept SNMP requests from any source?

Question 46

(0)

In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)

Question 47

(0)

Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?

Question 48

(0)

What is the role of a device that is simultaneously functioning as both the distribution and core in the hierarchy network model?

Question 49

(0)

Which statement about the IGMP snooping querier when enabled on a VLAN is true?

Question 50

(0)

Exhibit. You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device

Question 41

FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?

The handshake process timed out before FortiSwitch responded.

DTLS client hello had the incorrect pre-shared key.

The CAPWAP tunnel failed to come up due to a mismatch in time.

FortiSwitch has disabled FortiLink and is only managed as a standalone.

Show Answer Comment (0)

The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?

Assign a new LL0P profile to handle different LLDP-ME0 TLVs

Add power management as part of LLDP-MED TLVs to advertise.

Define an LLDP-ME0 location 10 to use standard protocols for power.

Create new a LLOP-MEO application type to define the PoE parameters.

Show Answer Comment (0)

Question 43

What can an administrator do to maintain the existing standalone FortlSwltch configuration while changing the management mode to FortLink?

Use a migration tool based on python script to convert the configuration

Enable the Forti-link setting on FortiSwitch before the authorization process

FortiGate will automatically save the existing FortiSwitch configuration during the Forti-link management process.

Show Answer Comment (0)

Question 44

Exhibit.

Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

These two routes have a higher administrative distance value available to the destina-tion networks.

These two routes will become primary, if the best routes are removed.

These two routes will be used as load-balancing routes.

These two routes are available in the hardware routing table.

Show Answer Comment (0)

Question 45

Exhibit.

Which configuration change will allow the managed FortiSwitch to accept SNMP requests from any source?

Create a new local access profile for SNMP only.

Enable SNMP on the internal interface of the switch.

Configure an SNMP host to send SNMP traps.

Add SNMP service on the management interface of the switch.

Show Answer Comment (0)

Question 46

In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)

Switch the FortiLink interface to the target VDOM.

Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.

Create a virtual port pool on the FortiGate CLI.

Assign a port to a VDOM directly on the managed FortiSwitch.

Show Answer Comment (0)

Question 47

Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?

Mirrored traffic can be sent across multiple switches.

SPAN can be configured only on a standalone FortiSwitch.

Traffic on the management interface can be mirrored and captured by the monitoring device.

The monitoring device must be connected to the same switch where the traffic is being mirrored

Show Answer Comment (0)

Question 48

What is the role of a device that is simultaneously functioning as both the distribution and core in the hierarchy network model?

POE with high density FortiSwitch

FortiGate managing FortiSwitch

FortiSwitch functioning as standalone

HA backup FortiGate managing FortiSwitch

Show Answer Comment (0)

Question 49

Which statement about the IGMP snooping querier when enabled on a VLAN is true?

Active multicast receiver entries are aging on each IGMP query sent on the VLAN

IGMP reports on the VLAN are forwarded to all switch ports.

The setting can only be enabled using the FortiSwitch CLI.

All other indirectly connected switches will be unable to get IGMP multicast traffic.

Show Answer Comment (0)

Question 50

Exhibit.

You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.

Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?

The management mode was set to use FortiLink mode.

Switch auto-discovery is enabled.

The management mode was set to use FortiLink mode.

The FortiSwitch device is scheduled to reboot as part the authorization process

The system time is not in-sync and is using a non-default value

Show Answer Comment (0)

Total 56 questions