Home / VCE / 210-015

VCE 210-015 Practice Test - Questions Answers, Page 5

Question list

List of questions

Question 41

(0)

You want to reset hardware sensors in the vSphere client connected to vCenter. Which statement describes how to accomplish this task?

Question 42

(0)

You power on a Vblock System 320 and look at the Maps tab of an ESXi server in vCenter's Hosts And Clusters view and see an ESXi server with a red "x" over it. What is causing the ESX server proble

Question 43

(0)

While reviewing the Vblock System 320 configuration, you verify the physical NIC mode is configured for failover for a teamed vSwitch. Which mode would be used to configure the NICs?

Question 44

(0)

You want to configure vMotion on a virtual switch in a Vblock System 320. Which network configuration is required?

Question 45

(0)

Which ESXi CLI command is used when installing VIB files on an ESXi host?

Question 46

(0)

What must you do to enable CLI access to the ESXi host through the DCUI?

Question 47

(0)

VMware vCenter Server provides which three functions? (Choose three.)

Question 48

(0)

Which statement is correct about using VMware Inventory Services?

Question 49

(0)

You are on deployment, and must enable the SSH service on an ESXi host. In the vSphere client GUI under Configuration, which submenu do you use to complete this task?

Question 50

(0)

While upgrading five hosts in a vSphere cluster, the maintenance window ends. The customer does not allow you to extend the window, so now the cluster is running the hosts at different build levels.

Related questions

You are implementing 32 new UCS B230 M3 blades into an existing Vblock System with 16 blades. After powering the new blades on, and migrating them to the Cisco Nexus 1000V, you notice that half of the new blades no longer respond to any network traffic. What is the cause?

You power on a Vblock System 320 and look at the Maps tab of an ESXi server in vCenter's Hosts And Clusters view and see an ESXi server with a red "x" over it. What is causing the ESX server problem?

A VM on the Vblock System 320 is unable to communicate on the customer network. When examining the virtual machine, you notice it has the same port group as the other VMs on the same ESXi server. Which action must you perform to resolve the problem?

Which two methods would you use to deploy an ESXi image created with Image Builder CLI? (Choose two.)

Which database platform is supported with VMware 5.x in a Vblock System?

While upgrading five hosts in a vSphere cluster, the maintenance window ends. The customer does not allow you to extend the window, so now the cluster is running the hosts at different build levels. There are two hosts at the new build version, and three hosts at the previous build version. There are 11 virtual machines protected by VMware Fault Tolerance in the cluster. You now see the following error No suitable host can be found to place the Fault Tolerance Secondary VM for virtual machine SalesVM. What is the cause of this error?

The ESXi 5.0 servers appear to have hardware problems after you have powered up the Vblock System 320. You want to view the log files for the ESXi servers. What are two ways to accomplish this task? (Choose two.)

During the deployment of a Vblock System, it was discovered that the Cisco Nexus 1000V VSM virtual machines were residing upon the same vSphere host in the AMP. To comply with VCE best practices for separating the Cisco Nexus 1000V VSM virtual machines, what is missing?

In a standard Vblock System 300 configuration with two vHBAs, the VNX Storage Processor A (SP-A) has rebooted. How will the hosts be impacted?

You want to configure vMotion on a virtual switch in a Vblock System 320. Which network configuration is required?

Question 41

You want to reset hardware sensors in the vSphere client connected to vCenter.

Which statement describes how to accomplish this task?

From the Hosts and Clusters view select a host, select the Hardware Status tab, and select the Reset sensors button.

From the Hosts and Clusters view select a host, select the Summary tab, select the Reset sensors button.

Select a virtual machine on the host, install the VMware tools, and reboot the host.

Hardware status can only be reset from the command line.

Show Answer Comment (0)

Question 42

You power on a Vblock System 320 and look at the Maps tab of an ESXi server in vCenter's Hosts And Clusters view and see an ESXi server with a red "x" over it.

What is causing the ESX server problem?

The server has crashed.

The server is an unsuitable candidate for migration.

The data store is out of space.

The server is rebooting.

Show Answer Comment (0)

Question 43

While reviewing the Vblock System 320 configuration, you verify the physical NIC mode is configured for failover for a teamed vSwitch.

Which mode would be used to configure the NICs?

active

passive

promiscuous

unused

Show Answer Comment (0)

Question 44

You want to configure vMotion on a virtual switch in a Vblock System 320.

Which network configuration is required?

Create an uplink port group, assign a unique IP address and subnet number, and select the Use This Port Group For vMotion option box.

Create a VMkernel port group on the network management virtual switch, and assign a unique IP address and subnet number.

Create a VMkernel port group on the virtual machine network, and assign a unique IP address and subnet number.

Create a VMkernel port group, assign a unique IP address and subnet number, and select the Use This Port Group For vMotion option box.

Show Answer Comment (0)

Question 45

Which ESXi CLI command is used when installing VIB files on an ESXi host?

esxcfg vib install

esxcli system vib install

vicfg-module vib install

esxcli software vib install

Show Answer Comment (0)

Question 46

What must you do to enable CLI access to the ESXi host through the DCUI?

Change the VLAN ID.

Disable the firewall ports.

Configure the management network.

Configure the troubleshooting options.

Show Answer Comment (0)

Question 47

VMware vCenter Server provides which three functions? (Choose three.)

multi-pathing

cloning of virtual machines

VMware vMotion

template creation

Active Directory LDAP services

Show Answer Comment (0)

Question 48

Which statement is correct about using VMware Inventory Services?

It tracks virtual machine locations in the data center.

It improves administrative user performance and reduces traffic with the vCenter.

It tracks data center objects and performs reports.

It improves virtual machine responsiveness.

Show Answer Comment (0)

Question 49

You are on deployment, and must enable the SSH service on an ESXi host. In the vSphere client GUI under Configuration, which submenu do you use to complete this task?

security profile

authentication services

advanced settings

system resource allocation

Show Answer Comment (0)

Question 50

What is the cause of this error?

Fault Tolerance requires that the hosts for the primary and secondary virtual machines use the same host build number and patch level.

Fault Tolerance has detected a difference between the primary and secondary virtual machines.

Fault Tolerance will not create a Secondary virtual machine in a cluster with mixed build versions.

VMware HA will not function properly in a cluster with mixed build versions, which prevents Fault Tolerance from creating a secondary virtual machine.

Show Answer Comment (0)

Total 83 questions

3 4 5 6 7

Go to page: of 9