Home / VCE / 210-015

VCE 210-015 Practice Test - Questions Answers, Page 9

Question list

List of questions

Question 81

(0)

You are asked to add two virtual machines to host ESXi01. The host IP address is 192.165.138.4. When you attempt to access the host using the vSphere client, you receive the following error message

Question 82

(0)

You experience problems after initially powering on a Vblock System with a mini AMP at a customer site. The vCenter services start properly but there is no network connectivity for the virtual machi

Question 83

(0)

You want to quickly apply groups of settings to new or existing ESXi servers. Which vSphere feature would be used?

Related questions

You are implementing 32 new UCS B230 M3 blades into an existing Vblock System with 16 blades. After powering the new blades on, and migrating them to the Cisco Nexus 1000V, you notice that half of the new blades no longer respond to any network traffic. What is the cause?

You power on a Vblock System 320 and look at the Maps tab of an ESXi server in vCenter's Hosts And Clusters view and see an ESXi server with a red "x" over it. What is causing the ESX server problem?

A VM on the Vblock System 320 is unable to communicate on the customer network. When examining the virtual machine, you notice it has the same port group as the other VMs on the same ESXi server. Which action must you perform to resolve the problem?

Which two methods would you use to deploy an ESXi image created with Image Builder CLI? (Choose two.)

Which database platform is supported with VMware 5.x in a Vblock System?

While upgrading five hosts in a vSphere cluster, the maintenance window ends. The customer does not allow you to extend the window, so now the cluster is running the hosts at different build levels. There are two hosts at the new build version, and three hosts at the previous build version. There are 11 virtual machines protected by VMware Fault Tolerance in the cluster. You now see the following error No suitable host can be found to place the Fault Tolerance Secondary VM for virtual machine SalesVM. What is the cause of this error?

The ESXi 5.0 servers appear to have hardware problems after you have powered up the Vblock System 320. You want to view the log files for the ESXi servers. What are two ways to accomplish this task? (Choose two.)

During the deployment of a Vblock System, it was discovered that the Cisco Nexus 1000V VSM virtual machines were residing upon the same vSphere host in the AMP. To comply with VCE best practices for separating the Cisco Nexus 1000V VSM virtual machines, what is missing?

In a standard Vblock System 300 configuration with two vHBAs, the VNX Storage Processor A (SP-A) has rebooted. How will the hosts be impacted?

You want to configure vMotion on a virtual switch in a Vblock System 320. Which network configuration is required?

Question 81

You are asked to add two virtual machines to host ESXi01. The host IP address is 192.165.138.4.

When you attempt to access the host using the vSphere client, you receive the following error message?

The vSphere client could not connect to 192.165.138.4. You do not have permission to login to server 192.165.138.4.

What would generate this error message?

The wrong IP address was used in the vSphere client.

Lockdown mode is enabled on host ESXi01.

Host ESXi01 has been powered off.

Host ESXi01 is in maintenance mode.

Show Answer Comment (0)

You experience problems after initially powering on a Vblock System with a mini AMP at a customer site. The vCenter services start properly but there is no network connectivity for the virtual machines. You determine that the virtual machines do not boot up in the correct order.

According to VCE best practice, what should be the virtual machine startup configuration in a Vblock System with a mini AMP?

VSM-1, SQL Server, vCenter Server, VUM Server, VSM-2, Array Management Server

SQL Server, vCenter Server, Array Management Server, VUM Server, VSM-1, VSM-2

Array Management Server, VSM-1, vCenter Server, SQL Server, VUM Server, VSM-2

vCenter Server, VUM Server, SQL Server, VSM-1, VSM-2, Array Management Server

Show Answer Comment (0)