ExamGecko
Login
Home / Cisco / 300-430 / List of questions
Ask Question

Cisco 300-430 Practice Test - Questions Answers, Page 3

Add to Whishlist

List of questions

Question 21

Report Export Collapse

An engineer is responsible for a wireless network for an enterprise. The enterprise has distributed offices around the globe, and all APs are configured in FlexConnect mode. The network must be configured to support 802.11r and CCKM.

What needs to be implemented to accomplish this goal?

Enable VLAN-based central switching.

Enable VLAN-based central switching.

Enable FlexConnect local authentication.

Enable FlexConnect local authentication.

Enable FlexConnect local switching.

Enable FlexConnect local switching.

Create FlexConnect groups.

Create FlexConnect groups.

Suggested answer: D
asked 07/10/2024
Gofaone Ncube
47 questions

Question 22

Report Export Collapse

A corporation has employees working from their homes. A wireless engineer must connect 1810 OEAP at remote teleworker locations. All configuration has been completed on the controller side, but the network readiness is pending. Which two configurations must be performed on the firewall to allow the AP to join the controller? (Choose two.)

Block UDP ports 1812 and 1813 on the firewall.

Block UDP ports 1812 and 1813 on the firewall.

Enable NAT Address on the 5520 with an Internet-routable IP address.

Enable NAT Address on the 5520 with an Internet-routable IP address.

Configure a static IP on the OEAP 1810.

Configure a static IP on the OEAP 1810.

Allow UDP ports 5246 and UDP port 5247 on the firewall.

Allow UDP ports 5246 and UDP port 5247 on the firewall.

Allow UDP ports 12222 and 12223 on the firewall.

Allow UDP ports 12222 and 12223 on the firewall.

Suggested answer: B, D
Explanation:

Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-3/b_Cisco_OfficeExtend_Access_Point_.pdf

asked 07/10/2024
Alemu, Fissha
40 questions

Question 23

Report Export Collapse

An enterprise has two WLANs configured on WLC. It is reported that when converting APs to FlexConnect mode, WLAN A works but WLAN B does not. When converting APs to local mode, WLAN B works, but WLAN A does not. Which action is needed to complete this configuration?

Create a Cisco FlexConnect group with WLAN-VLAN mapping.

Create a Cisco FlexConnect group with WLAN-VLAN mapping.

Disable local switching on the WLANs.

Disable local switching on the WLANs.

Map the AP group to the WLAN interface.

Map the AP group to the WLAN interface.

Join the APs to a Cisco FlexConnect group.

Join the APs to a Cisco FlexConnect group.

Suggested answer: A
asked 07/10/2024
bijay ghimire
42 questions

Question 24

Report Export Collapse

An engineer wants the wireless voice traffic class of service to be used to determine the queue order for packets received, and then have the differentiated services code point set to match when it is resent to another port on the switch.

Which configuration is required in the network?

Platinum QoS configured on the WLAN

Platinum QoS configured on the WLAN

WMM set to required on the WLAN

WMM set to required on the WLAN

msl qos trust dscp configured on the controller switch port

msl qos trust dscp configured on the controller switch port

msl qos trust cos configured on the controller switch port

msl qos trust cos configured on the controller switch port

Suggested answer: C
asked 07/10/2024
Vaniko Batiashvili
35 questions

Question 25

Report Export Collapse

When using a Cisco Catalyst 9800 Series Wireless Controller, which statement about AutoQoS is true?

It has a set of predefined profiles that you cannot modify further

It has a set of predefined profiles that you cannot modify further

It matches traffic and assigns each matched packet to QoS groups

It matches traffic and assigns each matched packet to QoS groups

It automates deployment of wired QoS and makes wireless QoS implementation easier

It automates deployment of wired QoS and makes wireless QoS implementation easier

It allows the output policy map to put specific QoS queues into specific subgroups

It allows the output policy map to put specific QoS queues into specific subgroups

Suggested answer: B
asked 07/10/2024
Gufran Dalwai
52 questions

Question 26

Report Export Collapse

A network engineer is deploying 8865 IP phones with wireless clients connected to them. In order to apply the appropriate QoS, the IP voice traffic needs to be distinguished from client data traffic.

Which switch configuration feature must be enabled?

Voice VLAN

Voice VLAN

QBSS

QBSS

WME

WME

QoS routing

QoS routing

Suggested answer: A
asked 07/10/2024
Karine Bashala
31 questions

Question 27

Report Export Collapse

A network engineer wants to implement QoS across the network that supports multiple VLANs. All the APs are connected to switch ports and are configured in local mode. Which trust model must be configured on the switch ports to which the APs are connected?

CoS

CoS

WMM UP

WMM UP

DSCP

DSCP

IPP

IPP

Suggested answer: C
asked 07/10/2024
Emmanuel Aminu
41 questions

Question 28

Report Export Collapse

An enterprise started using WebEx as a virtual meeting solution. There is a concern that the existing wireless network will not be able to support the increased amount of traffic as a result of using WebEx. An engineer needs to remark the QoS value for this application to ensure high quality in meetings. What must be implemented to accomplish this task?

QoS preferred call index

QoS preferred call index

UP to DSCP map

UP to DSCP map

AVC profiles

AVC profiles

WLAN quality of service profile

WLAN quality of service profile

Suggested answer: C
Explanation:

Reference: https://www.ciscolive.com/c/dam/r/ciscolive/apjc/docs/2018/pdf/BRKEWN-3003.pdf

asked 07/10/2024
Eric De La Vega
45 questions

Question 29

Report Export Collapse

A corporation has a wireless network where all access points are configured in FlexConnect. The WLC has a Data WLAN and a VoWiFi WLAN implemented where centrally-switched SSID is configured for the APs. Which QoS configuration must be implemented for the wireless packets to maintain the marking across the wired and wireless network?

Set QoS to Platinum.

Set QoS to Platinum.

Enable CAC.

Enable CAC.

Allow WMM.

Allow WMM.

Trust DSCP.

Trust DSCP.

Suggested answer: D
asked 07/10/2024
Cristian Pernia
46 questions

Question 30

Report Export Collapse

A company is collecting the requirements for an on-premises event. During the event, a wireless client connected to a dedicated WLAN will run a video application that will need on average 391595179 bits per second to function properly.

What is the QoS marking that needs to be applied to that WLAN?

Platinum

Platinum

Gold

Gold

Silver

Silver

Bronze

Bronze

Suggested answer: B
asked 07/10/2024
Hassene SAADI
45 questions
Total 216 questions
Go to page: of 22
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

An engineer must implement rogue containment for an SSID. What is the maximum number of APs that should be used for containment?
A wireless engineer must implement a corporate wireless network for a large company in the most efficient way possible. The wireless network must support 32 VLANs for 300 employees in different departments. Which solution must the engineer choose?
A Cisco CMX 3375 appliance on the 10.6.1 version code counts duplicate client entries, which creates wrong location analytics. The issue is primarily from iOS clients with the private MAC address feature enabled. Enabling this feature requires an upgrade of the Cisco CMX 3375 appliance in a high availability pair to version 10.6.3. SCP transfers the Cisco CMX image, but the upgrade script run fails. Which configuration change resolves this issue?
After receiving an alert about a rogue AP, a network engineer logs into Cisco Prime Infrastructure and looks at the floor map where the AP that detected the rogue is located. The map is synchronized with a mobility services engine that determines that the rogue device is actually inside the campus. The engineer determines that the rogue is a security threat and decides to stop if from broadcasting inside the enterprise wireless network. What is the fastest way to disable the rogue?
An engineer must implement a BYOD policy with these requirements: Onboarding unknown machines Easily scalable Low overhead on the wireless network Which method satisfies these requirements?
An engineer has configured passive fallback mode for RADIUS with default timer settings. What will occur when the primary RADIUS fails then recovers?
Refer to the exhibit. An engineer implemented the CPU ACL on your Cisco 5520 Series Wireless LAN Controller, and the controller is no longer manageable via the network. What must be changes on this CPU ACL to enable it to manage the controller again?
Refer to the exhibit. A network architect configured the Cisco Catalyst 9800 Series Controller to find out information on client types in the wireless network. RADIUS profiling is enabled so that the controller forwards the information about clients to a Cisco ISE server through vendor-specific RADIUS attributes. The ISE server is not profiling any data from the controller. Which configuration must be added in the blank in the code to accomplish the profiling on the Cisco 9800 Series controller?
An engineer is troubleshooting a Cisco CMX high-availability deployment and notices that the primary and backup Cisco CMX servers are both considered primary. Which command must the engineer run on the backup server?
A network engineer needs to configure multicast in the network. The implementation will use multiple multicast groups and PIM routers. Which address provides automatic discovery of the best RP for each multicast group?