Home / Cisco / 300-430

Cisco 300-430 Practice Test - Questions Answers, Page 6

Question list

List of questions

Question 51

(0)

A wireless engineer needs to implement client tracking. Which method does the angle of arrival use to determine the location of a wireless device?

Question 52

(0)

Which two steps are needed to complete integration of the MSE to Cisco Prime Infrastructure to track the location of clients/rogues on maps? (Choose two.)

Question 53

(0)

An IT department receives a report of a stolen laptop and has information on the MAC address of the laptop. Which two settings must be set on the wireless infrastructure to determine its location?

Question 54

(0)

Refer to the exhibit. An engineer needs to manage non-802.11 interference. What is observed in the output on PI?

Question 55

(0)

After looking in the logs, an engineer notices that RRM keeps changing the channels for non-IEEE 802.11 interferers. After surveying the area, it has been decided that RRM should not change the chan

Question 56

(0)

Which two protocols are used to communicate between the Cisco MSE and the Cisco Prime Infrastructure network management software? (Choose two.)

Question 57

(0)

An engineer must configure MSE to provide guests access using social media authentication. Which service does the engineer configure so that guests use Facebook credentials to authenticate?

Question 58

(0)

A network engineer has been hired to perform a new MSE implementation on an existing network. The MSE must be installed in a different network than the Cisco WLC. Which configuration allows the dev

Question 59

(0)

What is the default NMSP echo interval between Cisco MSE and a Wireless LAN Controller?

Question 60

(0)

An engineer just added a new MSE to Cisco Prime Infrastructure and wants to synchronize the MSE with the Cisco 5520 WLC, located behind a firewall in a DMZ. It is noticed that NMSP messages are fail

Related questions

A network engineer needs to configure multicast in the network. The implementation will use multiple multicast groups and PIM routers. Which address provides automatic discovery of the best RP for each multicast group?

Refer to the exhibit. A network architect configured the Cisco Catalyst 9800 Series Controller to find out information on client types in the wireless network. RADIUS profiling is enabled so that the controller forwards the information about clients to a Cisco ISE server through vendor-specific RADIUS attributes. The ISE server is not profiling any data from the controller. Which configuration must be added in the blank in the code to accomplish the profiling on the Cisco 9800 Series controller?

DRAG DROP A wireless engineer wants to schedule monthly security reports in Cisco Prime infrastructure. Drag and drop the report the from the left onto the expected results when the report is generated on the right.

A wireless engineer must implement a corporate wireless network for a large company in the most efficient way possible. The wireless network must support 32 VLANs for 300 employees in different departments. Which solution must the engineer choose?

Refer to the exhibit. An engineer needs to configure location services in an office. The requirement is to use FastLocate and achieve higher locations refresh rates. Which location-based technique should be implemented?

Which two restrictions are in place with regards to configuring mDNS? (Choose two.)

A customer is deploying local web authentication. Which software application must be implemented on Cisco ISE to utilize as a directory service?

An IT administrator deployed an OEAP to the home of a remote user, but the OEAP cannot reach the WLC. Which two configuration settings must be completed before an OEAP is deployed successfully? (Choose two.)

A wireless network has been implemented to enable multicast video to be streamed reliably over the wireless link to the wireless users. After a client reports that the video is unable to stream, the administrator determines that the client is connecting at a data rate of 12 Mbps and is trying to stream to a valid multicast address on the network. Which two actions must be applied? (Choose two.)

What two actions must be taken by an engineer configuring wireless Identity-Based Networking for a WLAN to enable VLAN tagging? (Choose two.)

Question 51

A wireless engineer needs to implement client tracking. Which method does the angle of arrival use to determine the location of a wireless device?

received signal strength

triangulation

time distance of arrival

angle of incidence

Show Answer Comment (0)

Question 52

Which two steps are needed to complete integration of the MSE to Cisco Prime Infrastructure to track the location of clients/rogues on maps? (Choose two.)

Synchronize access points with the MSE.

Add the MSE to Cisco Prime Infrastructure using the CLI credentials.

Add the MSE to Cisco Prime Infrastructure using the Cisco Prime Infrastructure communication credentials.

Apply a valid license for Wireless Intrusion Prevention System.

Apply a valid license for location tracking.

Show Answer Comment (0)

Question 53

An IT department receives a report of a stolen laptop and has information on the MAC address of the laptop. Which two settings must be set on the wireless infrastructure to determine its location?

(Choose two.)

Location History for Clients must be enabled on the MSE.

Client location tracking must be enabled on the MSE.

Location History for Visitors must be enabled on the MSE.

Location History for Rogue APs & Rogue Clients must be enabled on the MSE.

Tracking optimization must be enabled on the WLC.

Show Answer Comment (0)

Question 54

Refer to the exhibit.

An engineer needs to manage non-802.11 interference. What is observed in the output on PI?

At least one strong interferer is impacting connectivity at this site.

Several light interferers are collectively impacting connectivity at this site.

The three individual clusters shown indicate poor AP placement.

RF at this site is unable to provide adequate wireless performance.

Show Answer Comment (0)

After looking in the logs, an engineer notices that RRM keeps changing the channels for non-IEEE 802.11 interferers. After surveying the area, it has been decided that RRM should not change the channel. Which feature must be enabled to ignore non-802.11 interference?

Avoid Cisco AP Load

Avoid Non-802.11 Noise

Avoid Persistent Non-WiFi Interference

Avoid Foreign AP Interference

Show Answer Comment (0)

Question 56

Which two protocols are used to communicate between the Cisco MSE and the Cisco Prime Infrastructure network management software? (Choose two.)

HTTPS

Telnet

SOAP

SSH

NMSP

Show Answer Comment (0)

Question 57

An engineer must configure MSE to provide guests access using social media authentication. Which service does the engineer configure so that guests use Facebook credentials to authenticate?

Social Connect

Client Connect

Visitor Connect

Guest Connect

Show Answer Comment (0)

Question 58

A network engineer has been hired to perform a new MSE implementation on an existing network.

The MSE must be installed in a different network than the Cisco WLC. Which configuration allows the devices to communicate over NMSP?

Allow UDP/16113 port on the central switch.

Allow TCP/16113 port on the firewall.

Allow UDP/16666 port on the VPN router.

Allow TCP/16666 port on the router.

Show Answer Comment (0)

Question 59

What is the default NMSP echo interval between Cisco MSE and a Wireless LAN Controller?

10 seconds

15 seconds

30 seconds

60 seconds

Show Answer Comment (0)

Question 60

An engineer just added a new MSE to Cisco Prime Infrastructure and wants to synchronize the MSE with the Cisco 5520 WLC, located behind a firewall in a DMZ. It is noticed that NMSP messages are failing between the two devices.

Which traffic must be allowed on the firewall to ensure that the MSE and WLC are able to communicate using NMSP?

TCP 1613

UDP 16113

UDP 1613

TCP 16113

Show Answer Comment (0)

Total 216 questions