A system administrator connects a Cisco Nexus 2248PQ FEX to a fabric interconnect to expand the ports that are available for connecting Cisco UCS C-Series Rack Servers. In Cisco UCS Manager, the administrator doesnot see the servers connected to this FEX. Which action should be taken to resolve the issue?

The ports that connect the FEX to the fabric interconnects must be configured as server ports

The FEX must be exchanged so that it supports the connectivity between fabric interconnects and UCS CSeries servers

The fabric interconnects must be rebooted before the FEX is recognized

The transceivers must be exchanged to support the connectivity between the FEX and the fabric interconnects

The ports that connect the FEX to the fabric interconnects must be configured as server ports

Refer to the exhibit. Refer to the exhibit. An engineer discovered a VFC interface in a down state on a Cisco Nexus Switch.Which action resolves the problem?

Modify the fip keepalive message time to 30 seconds

Change the cable between the switch and the server

Reset the Cisco Nexus port toward the file server

Update the CNA firmware and driver versions

Modify the fip keepalive message time to 30 seconds

Refer to the exhibit. Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network. After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E

On MDS interface vfc 1/1, change switchport mode configuration to VF

On N9K interface vfc11, change switchport mode configuration to NP

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E

Refer to the exhibit. Refer to the exhibits. An engineer is implementing the SAN based on the Cisco MDS 9000 Series Switches. When operating the environment, the engineer encounters the error shown. Which action resolves the issue?

Add the World Wide Name of the neighboring switch to the MDS-1 switch

Copy VSAN 101 to the fabric binding database on the MDS-1 switch

Add the World Wide Name of the neighboring switch to the MDS-1 switch

Configure the port security feature on the MDS-1 switch

Enable VSAN 101 on the peer MDS 2 switch fabric interconnect

When the engineer runs the command, this error is received: opsengineer@wkst1:/home/auto/bash_scripts$ curl –s –b cookie_file_39422186.txt –X GET –k 192.15.132.101/api/node/class/Tenant.json{“totalCount”:”1”,”imdata”:[{“error”:{“attributes”:{“code”:”400”,”text”:”Request failed, (output omitted)”}}}]} Which action resolves the issue?

Modify the URI to 192.15.132.101/api/node/class/fvTenant.json

Regenerate the API token object

Modify the URI to 192.15.132.101/api/node/class/fvTenant.json

Add the –c class Tenant flag to the cURL command

Refer to the exhibit. Refer to the exhibit. A network engineer creates an EEM script to trigger an SNMP notification when a user enters configuration mode, but the trap is not received when the condition is met. Which action resolves the issue?

Append action 2.0 event-default to the script

Append action 2.0 cli “conf t” to the script

Modify snmp-trap strdata “Configuration changed” to syslog msg Configuration changed

Modify cli match “conf t” to “snmp match “conf t”

Refer to the exhibit. The script fails to bring up Ethernet 1/2 when Ethernet 1/1 goes down. Which change enables the script to run as intended?

Add an action to configure the terminal

Include an action to manually shut down Ethernet 1/1

Add an action to configure the terminal

Refer to the exhibit. Refer to the exhibit. A functioning trunk port Ethernet1/48 exists between two identical Cisco Nexus 5000 Series Switches. The interfaces on the switches support the MACsec feature and are configured identically. To enable manualMACsec, an engineer adds the configuration shown in the exhibit to both sides of the trunk. The trunk port stops functioning. Which action should be taken to resolve the issue?

Enable the license for the trunk ports to support MACsec

Disable and then enable the port

Enable the license for the trunk ports to support MACsec

Lower the MTU value to less than 9216 bytes

Configure the PMK with a length of 2048 bytes

Refer to the exhibit. Refer to the exhibit. A network engineer is troubleshooting a Cisco Nexus 5000 Series Switch. The interface between the server and the switch is nonoperational and is expected to operate at 10 Gbps. The drain rate of the interface is 3 Mbps. Which action resolves the issue?

Configure pause error-disable recovery

Enable link level pause on the interface

Set priority flow control pause

Refer to the exhibit.A customer network uses OSPFv2 and MP-BGP protocols A network administrator installs a new Cisco Nexus Switch in the data center but experiences a BGP RIB failure Which action solves the issue?

Change the administrative distance of OSPF to 220

Configure the route as a BGP backdoor

Use a filter list for OSPF to filter both routes

An engineer is implementing a new BGP peering in their new data center. The engineer set up the BGP session that peers with the remote end. As soon as the BGP peers attempt to exchange routing prefixes, one of the BGP peers drops the connection. After reviewing the configuration, the engineer reviews the logging messages. The engineer discovers that the router is missing keepalives from the remote end and terminates the session. Which action resolves the issue?

Set the higher values for the BGP keepalive and hold-down timers on both peers

Set the bgp transport path-mtu-discovery attribute on both peers

Set the higher values for the BGP keepalive and hold-down timers on both peers

Configure the matching BGP AS numbers between the peers

Configure the matching BGP passwords between the peers

Refer to the exhibit. The vPC neighborship between two switches is in suspended state. Which configuration change resolves the issue and brings up the vPC neighborship?

Configure QoS MTU value of 9216 on the peer switch

Change STP Port Type to Network on the peer switch

Enable Bridge Assurance on the local switches

Configure QoS MTU value of 9216 on the peer switch

Add VLAN 400-401 to the configuration on the local switch

Refer to the exhibit. The integration between Cisco UCS Manager and Cisco UCS Central failed. Which action resolves the issue?

Implement the consistent NTP source between the appliances

Implement the connectivity between the appliances through a firewall

Configure the certificate between the appliances

Configure the shared secret key between the appliances

Refer to the exhibit. An engineer fails to implement a Cisco UCS Manager integration manager. The credentials and IP connectivity between Cisco APIC and UCS Manager are configured as expected. Which action resolves the issue?

Install ExternalSwitch app in the APIC controller

Disable HTTP to HTTPS redirection in Cisco UCS Manager

Enable JSON API on the Cisco UCS Manager

Change the Integration Manager name to FQDN of the Cisco UCS Manager

Install ExternalSwitch app in the APIC controller

A network engineer experiences the error “DDR3_P1_B1_ECC” when upgrading Cisco UCS firmware.Which action resolves the issue?

Reflash the controller firmware

Refer to the exhibit. A Cisco UCS Fabric Interconnect fails during the upgrade process. The working images of the fabric interconnect are stored on the bootflash. Which set of commands recovers the fabric interconnect?A. loader> dirloader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.binswitch(boot)# init systemswitch(boot)# reloadswitch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

loader> dirloader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.binswitch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.binswitch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

loader> dirloader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.binswitch(boot)# init systemswitch(boot)# reloadswitch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

loader> dirloader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.binswitch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.binswitch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

Refer to the exhibit. An engineer monitors a Cisco UCS server logs and discovers a blade discovery issue. Which procedure resolves the issue?A. 1. Verify the server power module.

Decommission the faulty module.

1. Verify that server platform power is failed

Resolve the platform power issue.

1. Verify the FSM status on the server.

Decommission the impacted server.

Reset the slot where the server is located.

Refer to the exhibit. A network engineer finds one of the fabric interconnects offline when connecting L1 and L2 ports on both fabric interconnects. Which action resolves the issue?A. 1. Connect to Fabric Interconnect B.

Verify the cluster status and HA election.

Validate Fabric Interconnect B hardware issues.

1. Connect to Fabric Interconnect A.

Verify the cluster status and HA election.

Validate Fabric Interconnect A hardware issues.

1. Connect Fabric Interconnect B and change the role to primary.

Add the Fabric Interconnect A as subordinate fabric to the cluster.

1. Connect Fabric Interconnect B and execute “Erase configuration”

Reboot Fabric Interconnect B.3. Add the subordinate Fabric Interconnect to the cluster.

Refer to the exhibit. A network engineer upgrades the firmware of a Cisco Fabric Interconnect from boot flash. During the process, the fabric interconnect reboots and displays the message shown in the exhibit. Which action resolves the issue?

Reload the switch and boot the kickstart image from the TFTP server

Remove the service pack and upgrade through the auto-install procedure

Reset the I/O module and install the firmware image from the boot flash

Boot the kickstart image from boot flash and load the system image

Reload the switch and boot the kickstart image from the TFTP server

Refer to the exhibit. A Cisco UCS B-Series Blade Server is configured to boot from a shared storage via an iSCSI network.When a service profile is associated with the blade, the blade fails to attach the LUN. Which action resolves the issue?

Place VLAN 0 on the interface that connects to the storage

Register the blade as an initiator on the storage array

Implement a Layer 3 connection between the blade and the storage

Establish a Layer 2 connection between the blade and the storage

Refer to the exhibit. A network engineer is implementing a Cisco UCS environment. The environment consists of eight servers configured with the same service profile template and Windows 2012 installed. The VFC interfaces of five of these servers are showing the error shown in the exhibit. Which action resolves the issue?

Decommission and recommission the servers

Modify the vHBAs name in the storage connectivity policy

Decommission and recommission the servers

Modify the boot order in the boot policy

Refer to the exhibit. A client configures an upgrade of its Cisco Nexus switches that are connected to the Cisco ACI controller, such that the switches are upgraded one at a time. After the upgrade is run, it is discovered that both Cisco Nexus switches were upgraded simultaneously. Which two actions ensure that the switches upgrade one at a time? (Choose two.)

Select the "Graceful Maintenance" checkbox

Place each leaf switch in a different upgrade group

Configure the *Do not pause on failure and do not wait on cluster health" Run Mode

Choose the 'Pause upon upgrade failure" Run Mode

Select the "Graceful Maintenance" checkbox

Place each leaf switch in a different upgrade group

Check the Ignore Compatibility" checkbox

Refer to the exhibit. An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric. Which action resolves the issue?

Match the VSAN membership on both ends of the connection.

Enable the NPIV mode on the Cisco Nexus 5000 switch.

Match the VSAN membership on both ends of the connection.

Configure the BB_credit buffer on the uplink port.

Replace the SFP in slot fc2/12.

An engineer configures FCoE between a set of ESXi hosts and a Cisco Nexus 5000 Series Switch. The Converged Network Adapter of the host fails to receive the response from the Cisco Nexus device.Also, the VFC interface is in a down state and the FIP adapter fails to receive 802.1q tagged frames.The host interface is configured for VLAN trunking. Which action resolves the issue?

Configure the UF link as a spanning-tree edge port

Activate the reception of Xoff pause frames from the server

Configure the UF link as a spanning-tree edge port

Enable the active STP port state on the bound Ethernet interface

Set the bound Ethernet trunk interface to non-FCoE native VLAN

The script fails to convert a JSON variable into a Python dictionary. Which action resolves the issue?

Fix the JSON syntax by modifying “attribures” to “attribures”:

Use a json.dumps(json_output) function

Define a json_output as a YAML object, yaml json_output

Fix the JSON syntax by modifying “attribures” to “attribures”:

Invoke a function yaml.loads(json._output ,decoder_”json”)

Refer to the exhibit. An engineer is experiencing a problem when running a Docker container inside the Cisco Nexus 9000 bash shell. Which action resolves the issue?

Connect to bash as a different user

Refer to the exhibit. A Postman call to a Cisco APIC fails. The access credentials were confirmed to be configured as expected. Which action resolves the issue?

Change the IP address to a domain name

Modify the target protocol type to XML

Refer to the exhibit. The scheduler was configured to save the running-config automatically daily. However, the scheduler is returning the error presented. Which action resolves the issue?

Change the file transfer protocol to TFTP in scheduler job

Reconfigure the scheduler using the admin user

Use the kstack attribute for copying the configuration file

Remove vrf management from the command

Change the file transfer protocol to TFTP in scheduler job

Refer to the exhibit. RBAC is configured on the MDS switch for a new SAN administrator engineer to work on the FSPF configuration. However, after the configuration is applied the engineer who was assigned the FSPF_Admin role cannot perform any configuration changes. Which action resolves the issue?

Configure the switch license for RBAC

Refer to the exhibit. An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?

Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command

Commit the active database with the port-security database copy vsan 1 command

Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command

Disable CFS distribution with the no port-security distribute vsan 1 command

Commit the changes with the port-security commit copy vsan 1 command

Refer to the exhibit. A network administrator must delete a feature group from a Cisco Nexus 5000 Series Switch. Which action resolves the issue?

Detach the association with the no role command within the feature-group configuration mode

Detach the association with the no rule command within the role configuration mode

Detach the association with the no role command within the feature-group configuration mode

Detach the association with the no rule command within the feature-group configuration

Detach the association with the no role command within the role configuration mode

Refer to the exhibit. An engineer discovers that if the vPC peer link goes down, half of the devices in VLAN 20 experience connectivity issues with the external networks Which action resolves the issue?

Add the non-vPC SVIs in the dual-active exclude VLAN list

Configure a dedicated Layer 3 link between vPC peers

Allow non-vPC VLANs on a second trunk between the two vPC peers

Add the non-vPC SVIs in the dual-active exclude VLAN list

Exclude the non-vPC VLANs from vPC peer link

Refer to the exhibit. An engineer is troubleshooting the connectivity between Server-1 and Server-2. Which action resolves the connectivity issue?

Classify CFS messages for strict priority queue on spine switches

Enable BGP advertise pip feature on both leaf switches

Configure the same source IP address on NVE and virtual peer link on leaf switches

Classify CFS messages for strict priority queue on spine switches

Change all ports on spine switches as port-type fabric

Refer to the exhibit. A client reports that the routing protocol neighborship fails to start between two Cisco Nexus switches, N9K-1 and N9K-2. Which action resolves the issue?

Configure a unicast access list to allow the negotiation between N9K-1 and N9K-2

Add OSPF routing configuration to interface e1/1 on both Cisco Nexus switches

Configure a unicast access list to allow the negotiation between N9K-1 and N9K-2

Configure a multicast access list to allow the negotiation between N9K-1 and N9K-2

Add MTU configuration to interface e1/1 on both Cisco Nexus switches

What does this adapter output indicate? adapter 1/6/1 (fls): 2# lunlist 9 vnic: 9 lifid: 6- FLOGI State : flogi est (fc_id Oxac0e04)- PLOGI Sessions- WWNN 50:0a:09:83:8d:53:43:44 WWPN 50:0a:09:83:8d:53:43:44 fc_id 0x000000- LUN's configured (SCSI Type, Version, Vendor, Serial No.)- LUN ID: Ox0000000000000000 access failure-REPORT LUNs Query Response- Nameserver Query Response-WWPN: 54:b1:6a:94:64:3e:73:44

The target of the configured zone does not match the target of the configured boot order

The configured initiator LUN ID does not match the configured target LUN ID

The target device configuration does not allow the initiator to access the LUN

The port types between the target and initiator are incorrectly configured

The target of the configured zone does not match the target of the configured boot order

Refer to the exhibit. The FCoE traffic fails to traverse the vfc2 interface. The VSAN 102 is configured for vfc2. Which action resolves the issue?

Enable LLDP on the neighbor switch

Enable LLDP on the interface vfc2

Activate DCBX on the N9K switch

Activate DCBX on the interface e101/1/2

Enable LLDP on the neighbor switch

Cisco 300-615 Practice Test 3 - Free Online Exam Prep & Questions

A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-615 Practice Test 3

Question

Cisco 300-615 Practice Tests

Practice Tests