ExamGecko
Login
Home / Huawei / H12-261 / List of questions
Ask Question

Huawei H12-261 Practice Test - Questions Answers, Page 7

Add to Whishlist

List of questions

Question 61

Report Export Collapse

SWA and SWB are connected through two physical Ethernet links. SWA has the following interface configurations:

Huawei H12-261 image Question 61 32083 09182024192157000000

The two links are aggregated.

Assume that the configuration on SWB is correct. Given this information, which of the following statements are true?

Become a Premium Member for full access
  Unlock Premium Member

Question 62

Report Export Collapse

Which of the following command outputs indicates that a loop has occurred on a switch?

Become a Premium Member for full access
  Unlock Premium Member

Question 63

Report Export Collapse

Which of the following statements regarding the process of sending and receiving data frames on a port in access link-type is true?

Become a Premium Member for full access
  Unlock Premium Member

Question 64

Report Export Collapse

How long will a Huawei running RSTP wait before aging out the BPDUs on an interface?

Become a Premium Member for full access
  Unlock Premium Member

Question 65

Report Export Collapse

Which of the following statements regarding LACP are true?

Become a Premium Member for full access
  Unlock Premium Member

Question 66

Report Export Collapse

Which of the following statements regarding PPPoE data frames are true?

Become a Premium Member for full access
  Unlock Premium Member

Question 67

Report Export Collapse

As shown in the figure below, R1 and R2 are connected through a PPP link, and the IP addresses on the directly connected interfaces are not on the same network segment. R1 and R2 can communicate with each other through the directly connected interfaces. However, communication on the Ethernet link fails if the IP addresses on the directly connected interfaces are on the same network segment. What are the causes of this?

Huawei H12-261 image Question 67 32089 09182024192157000000

Become a Premium Member for full access
  Unlock Premium Member

Question 68

Report Export Collapse

Routes received from AS100 match the AS-Path filter configured using the ip as-path-filter 10 permit_100$ command.

Become a Premium Member for full access
  Unlock Premium Member

Question 69

Report Export Collapse

On a broadcast network, DIS election starts only after the neighbor relationship is established.

Become a Premium Member for full access
  Unlock Premium Member

Question 70

Report Export Collapse

Which of the following attributes cannot be directly referenced by the if-match clause of route-policies?

Become a Premium Member for full access
  Unlock Premium Member
Total 298 questions
Go to page: of 30
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which of the following statements regarding CE dual-homing features is false?
Which packet type is used when BGP EVPN is used to establish VXLAN tunnels?
Subnets of one subnet is as follows: RT=10:10 both and TR=1000:1000 export in the EVPN instance and RT=100:100 in the VPN instance. Which of the following configurations can be made for another subnet?
Which of the following statements regarding Filter-policy is true?
Which of the following statements regarding the stub area and NSSA in OSPF is false?
Which of the following AS-_Path attribute values can be matched by the AS-Path filter configured using ip as-path filter 1 permit .*(100|400$command?
The VRRP priority cannot be set to 0, so the device that sends a VRRP packet with priority 0 stops participating in the VRRP group and notifies the backup device to become the master device right away, without waiting for the Master_Down_Interval timer to expire?
The Next Header field only exists in the basic header of an IPv6 packet, and its function is only to indicate whether the IPv6 packet has an extension header.
Assume that BGP/MPLS IPv4 VPN configured with OSPF, LDP, and static routing has been deployed on a PE router. To enable the NSF function, which of the following protocols need to be configured to enable the GR function on the PE router?
On router HW1, you want to view the status of a frame relay connection. Which "display" commands will show the status of a Frame-Relay PVC? (Multiple choice)