ExamGecko
Login
Home / Huawei / H35-260 / List of questions
Ask Question

Huawei H35-260 Practice Test - Questions Answers, Page 3

Add to Whishlist

List of questions

Question 21

Report Export Collapse

L--16.1 indicates the type of optical interface. Which of the following descriptions is correct?

Short distance communication, the signal level is STM-1 and the working window is 1310nm
Short distance communication, the signal level is STM-1 and the working window is 1310nm
Long distance communication, the signal level is STM-1 and the working window is 1310nm
Long distance communication, the signal level is STM-1 and the working window is 1310nm
Short distance communication, the signal level is STM-16 and the working window is 1550nm
Short distance communication, the signal level is STM-16 and the working window is 1550nm
Short-distance week-to-week communication, the signal level is STM-16 and the working window is 1310nm
Short-distance week-to-week communication, the signal level is STM-16 and the working window is 1310nm
Suggested answer: D
asked 18/09/2024
Rannie Dayapan
46 questions

Question 22

Report Export Collapse

Which of the following protection types is not supported by the L302 board?

0DU3 SNCP
0DU3 SNCP
Tributary SNCP
Tributary SNCP
SW SNCP
SW SNCP
In-board 1+1
In-board 1+1
Suggested answer: C
asked 18/09/2024
Asif Khan
50 questions

Question 23

Report Export Collapse

Which of the following LSRs are passed by an LSP?

Ingress
Ingress
Lable
Lable
Transit
Transit
Egress
Egress
Suggested answer: A, C, D
asked 18/09/2024
Kristian Michael Matias
53 questions

Question 24

Report Export Collapse

Where in the L2/L3 node is the VLAN in the Layer 2 header stripped in the packet sent by the base station in the LTE solution?

Network side interface
Network side interface
L2VE sub-interface
L2VE sub-interface
L3VE sub-interface
L3VE sub-interface
LOOPBACK interface
LOOPBACK interface
Suggested answer: C
asked 18/09/2024
BISWARUP KUNDU
45 questions

Question 25

Report Export Collapse

Which of the items are unreasonable to configure the default route on the PTN device in the LTE solution?

The default route is configured on the L2/3 master node, and the next-hop points to the L3 master node
The default route is configured on the L2/3 master node, and the next-hop points to the L3 master node
A default route is configured on the L2/L3 standby node, and the next hop points to the L3 master node
A default route is configured on the L2/L3 standby node, and the next hop points to the L3 master node
On the L3 raw node, configure a default route with the next hop pointing to the main L2/L3 node
On the L3 raw node, configure a default route with the next hop pointing to the main L2/L3 node
Configure the default route on the standby point, and the next hop points to the standby L2/L3 node
Configure the default route on the standby point, and the next hop points to the standby L2/L3 node
Suggested answer: C, D
asked 18/09/2024
Pawel Szalek
41 questions

Question 26

Report Export Collapse

In the LTE service, X2 traffic forwarding between base stations needs to be enabled. Which of the following statements about the forwarding path in the x2 traffic flow is correct?

X2 traffic forwarding on the same network segment does not require Layer 3 routes or interfaces
X2 traffic forwarding on the same network segment does not require Layer 3 routes or interfaces
For forwarding in the X2 flow between base stations on different network segments under the same L2L3 node, it is necessary to transfer between L3VE sub-interfaces
For forwarding in the X2 flow between base stations on different network segments under the same L2L3 node, it is necessary to transfer between L3VE sub-interfaces
Different L2L3 nodes must forward the X2 traffic with the base station to the base station, and it must be transited by the L3 node.
Different L2L3 nodes must forward the X2 traffic with the base station to the base station, and it must be transited by the L3 node.
X2 traffic forwarding between different cities requires SGW participation
X2 traffic forwarding between different cities requires SGW participation
Suggested answer: B
asked 18/09/2024
Georgios Kavvalakis
36 questions

Question 27

Report Export Collapse

The M40 board has 2 waves of access, and the power of each wave is -4dBm. So which of the following values is the power of the M40 output port? (M40 insertion loss is 6.5dBm)

-8.5
-8.5
-1
-1
-10.5
-10.5
-7.5
-7.5
Suggested answer: D
asked 18/09/2024
Leandro Franklin Franklin
51 questions

Question 28

Report Export Collapse

Which of the following item levels are included in the MPLS-TP OAM detection object?

Section layer
Section layer
Tunnel layer
Tunnel layer
Link Layer
Link Layer
PW layer
PW layer
Suggested answer: A, B, D
asked 18/09/2024
steven Hughes
41 questions

Question 29

Report Export Collapse

The MPLS label has four identification fields, Lable, EXP, S and TTL, with a total of 4 bytes, of which Lable occupies 20 bits. The label value 0-15 is reserved for special purposes, which indicates that the inner payload carried is MPLS-OAM packet. , the label value is which of the following?

0
0
1
1
3
3
14
14
Suggested answer: D
asked 18/09/2024
Chrysovalantis Oikonomopoulos
41 questions

Question 30

Report Export Collapse

MPLS is used to label packets instead of IP forwarding. Which of the following descriptions about MPLS packet encapsulation are correct?

The Type field in the ETH header is set to 0x8847 to indicate that it is followed by MPLS label encapsulation
The Type field in the ETH header is set to 0x8847 to indicate that it is followed by MPLS label encapsulation
The nested encapsulation of MPLS can only be two layers, PW and Tunnel two layers of labels
The nested encapsulation of MPLS can only be two layers, PW and Tunnel two layers of labels
The MPLS label of the Tunnel carrying the PW, where the S bit is set to 1
The MPLS label of the Tunnel carrying the PW, where the S bit is set to 1
IP packets can be directly carried on the Tunnel
IP packets can be directly carried on the Tunnel
Suggested answer: A, D
asked 18/09/2024
Kristian Gutierrez
50 questions
Total 338 questions
Go to page: of 34
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which one is correct about the description of MC-LAG on L2/13 nodes in LTE network?
Which of the following 7900 single-board software function descriptions are correct?
The U2000 license file is stored in the following directory /u2000/server path. If the license file is invalid, the U2000 will not work normally.
The base station is deployed, the Tunnel and PW tests are normal, and the base station management is normal, but the base station cannot access the core network normally. What is the reason for the impossibility?
On the PTN equipment, when the tunnel bears data and forwards, which one is wrong in the description of the actions of each node on the LSP?
To determine whether the optical fiber lines and connectors on the wavelength division side are normal, which of the following loopback methods is most suitable?
PTN can support in-band DCN. At this time, the port needs to enable the DCN function. Therefore, in CES service, PTN setup cannot be managed by in-band DCN.
When the data is forwarded by the PTN device, when the value of the TYPE field of the Ethernet header is OxO8O0, which protocol is the encapsulated inner packet?
When the switch is working, the device forwards data according to the MAC address forwarding table. Which of the following statements is correct?
When TCAT adds points, it recalculates the Tunnel and distributes the configuration. Which of the following information is being modified?