Cisco 300-510 Practice Test - Questions Answers, Page 18
Question list
List of questions
Related questions
Refer to the exhibit.
Refer to the exhibit. An engineer working for a private telecommunication company with an employee id: 4233:46:364 notices that the customer network going through AS30-AS65001-AS65000 is experiencing packet drops when it accesses an application at 172.16.20.1/32 In the DC cloud. The BGP link between AS20 and AS30 is inaccessible because of a fiber cut. Routers RL, RN, and RZ are configured with confederation identifier 10. Which action resolves this Issue?
Option A
Option B
Option C
Option D
Which type of BGP attribute does a route reflector attach to routes learned from iBGP peers that allows them to be accepted by other iBGP peers, thereby eliminating the need for a full-mesh BGP topology?
well-known mandatory
optional transitive
well-known discretionary
optional non transitive
Refer to the exhibit.
The UserA device fails to recede IPTV streaming traffic from the source While debugging the issue a network engineer finds that routers RB and RC receive the multicast traffic normally RC receives subscription messages from UserA to join the IPTV stream Which action must the engineer lake on router RA to correct this problem?
Configure ip pim ssm with ip igmp version 2 on interface GigabitEthernet 1/0.
Remove the ip pim ssm default configuration and replace it with ip pim rp-address 10.10.1.3
Change ip igmp version 2 to ip igmp version 3 on interface GigabitEthernet 1/0.
Configure ip pim bidir-enable in global mode and add ip pim rp-address 10.10.10.3
DRAG DROP
Drag and drop the route-manipulation methods from the left onto their features on the right
Refer to the exhibit.
Refer to the exhibit. A network engineer commissioned Router 1, which connects lo Router 2 and Router 5 Router 1 participates in IS-IS routing with other routers, but it is not used for transit traffic. Traffic from Router 2 to Router 5 is expected to travel via Router 1 but the traffic is travelog via Router 3 and Router 4 Which action reserves this problem?
Add hello padding on Router 1
Remove the hello padding on Router 5
Add the overload bit on Router 5
Remove the overload bit on Router 1.
Refer to the exhibit.
Refer to the exhibit Router 1 resides in a different data center than Rouler 2 and Router 3. Router 1 is running the IS-IS routing protocol, and it is preconfigured with LDP and segment routing Which configuration must the engineer apply under router isis 111 on Router 1 to implement Tl-LFA on the link to Router 2 without disrupting traffic to Router 3?
A)
B)
C)
D)
Option A
Option B
Option C
Option D
Refer to the exhibit.
Refer to the exhibit. Unified MPLS is implemented on this network to provide end-to-end services A network engineer noticed that R3 is failing to receive labels from R1 However, R2 is receiving labels from R1 R3 can ping R1 normally Which action resolves the issue?
Add the cdp run command to the link configuration between R1 and R3.
Add the send-label keyword in the R1 neighbor statement for R3.
Configure R1 to run Unified MPLS on both interfaces.
Disable mpls Ip on the link between R1 and R3
Refer to the exhibit.
Refer to the exhibit. Customer A and customer B are connecting through a service provider network with these requirements
R1 acts as the mapping server to connect 10 0 0.0/30 and 172.16.0.0/30 networks
R1 and R2 are using nondefault SRG8 range to allocate SID.
R2 ads as the mapping client for transient traffic originating from customer A
Which configuration meets the requirements?
Remove allocation of prefix SlDs for 10.0.0.0/30 and 172.16.0.0/30 on R1.
Configure segment-routing prefix-sid-map advertise-local on R1
Allocate prefix SIDs for 10.0.0.0-30 and 172.16 0.0/30 subnets on R2
Configure segment-routing prefix-sid-map advertise-local on R2.
Question