ExamGecko
Login
Home / Cisco / 300-510 / List of questions
Ask Question

Cisco 300-510 Practice Test - Questions Answers, Page 22

Add to Whishlist

List of questions

Question 211

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 211 112922 10072024005946000000

Refer to the exhibit. An engineer is troubleshooting a network routing issue on this IS-IS network situated at the customer's regional hub. Router 2 that runs Cisco IOS XR Software cannot see the network 10.1.1.0/24 on router 1. The Layer 2 encapsulations are correct. The ARP connectivity for the Ethernet interface that runs IS-IS is working. Which action resolves the issue?

Become a Premium Member for full access
  Unlock Premium Member

Question 212

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 212 112923 10072024005946000000

Refer to the exhibit. Which duplicate configuration causes this message during setup of an MPLS BGP network?

Become a Premium Member for full access
  Unlock Premium Member

Question 213

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 213 112924 10072024005946000000

Refer to the exhibit. HostB receives an IPTV traffic stream from the multicast source at 192.168 10.1. When router RB is powered down, it impacts multicast traffic forwarding to downstream peers. The RA and RB routers reside in the same physical location. Which two configurations must be implemented so that HostB receives the multicast stream even when RB is powered down? (Choose two )

Become a Premium Member for full access
  Unlock Premium Member

Question 214

Report Export Collapse

Refer to the exhibit.

Cisco 300-510 image Question 214 112925 10072024005946000000

Refer to the exhibit. Router R1 is expected to receive routes that originate from AS 65547 only. However, R1 is receiving routes from AS 65547 and several other ASs that are directly attached to it. Which change to the AS path permit filter corrects the problem?

Become a Premium Member for full access
  Unlock Premium Member
Total 214 questions
Go to page: of 22
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. Refer to the exhibit. Users connected to an application on 1.1.1.1 via routers CE1 and CE2 are complaining of frequent disconnections. While troubleshooting the issue, a network engineer with an employee ID: 4333:96:916 determined that the application itself is working normally, but the link connected to the 1.1.1.1 application is flapping. The users on CE1 and CE2 are accessing applications on 2.2.2.2 without difficulty. Which action resolves the issue?
Refer to me exhibit. A network engineer sets up a multihoming eBGP topology where multiple Autonomous Systems connect to ASN 64501. The engineer wants to block all the routers coming from ASN 64502. but allow all the others. For that purpose, the following AS Pam prefix 1st s being used: What must be fixed to achieve this result?
Refer to the exhibit.
Refer to the exhibit. An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?
Guidelines This is a lab item in which tasks will be performed on virtual devices. Refer to the Tasks tab to view the tasks for this lab item. Refer to the Topology tab to access the device console(s) and perform the tasks. Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window. All necessary preconfigurations have been applied. Do not change the enable password or hostname for any device. Save your configurations to NVRAM before moving to the next item. Click Next at the bottom of the screen to submit this lab and move to the next question. When Next is clicked, the lab doses and cannot be reopened. Topology Tasks Configure and verify an OSPF neighbor adjacency between R1 and R2 in OSPF area 0 according to the topology to achieve these goals: 1. R1 pings the Loopback0 interface of R2. Use interface-level configuration to complete this task. 2. R2 pings the Loopback0 interface of R1. Use interface-level configuration to complete this task. 3. R2 receives a single summary route 172.16.100.0/22 for networks 172.16.100.0/24, 172.16.101.0/24, and 172.16.103.0/24.
Refer to the exhibit. Routers within the cluster are not receiving the desired prefixes. What must be done to fix the issue?
Refer to the exhibit. The green policy is designed with low delay, and the pink policy is designed with low cost. What is the next hop for node A on its way to node D, with the objective of achieving a low delay?
Refer to the exhibit. Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?
Refer to the exhibit. Refer to the exhibit. Company A established BGP sessions with several ISPs. A network engineer at the company must filter out all traffic except for routes that transit AS 152. The engineer configured the filtering policy “permit _152S_(_ [0.9])” on R1, but after applying the configuration, the engineer notices that other routes are still visible. Which action resolves the issue?
Refer to the exhibit. Refer to the exhibit A network engineer installed a new router (router 3) at the regional hub running MPLS services for scalability Router 3 is connected to the 10.44 4.0,'24. 10.44 5.024. 10 44.6.0/24. and 10 44 7 0/24 subnets The new router has been configured for OSPF area 2. and it is advertising the four connected networks. The engineer noticed that the same networks are listed as interarea summary routes, and they are being flooded into each area on the area borders Which action resolves the issue?