ExamGecko
Login
Home / Network Appliance / NS0-163 / List of questions
Ask Question

Network Appliance NS0-163 Practice Test - Questions Answers, Page 12

List of questions

Question 111

Report Export Collapse

You have quiesced a volume to stabilize the contents of a destination just prior to a snapshot. What is the next logical command that you would issue after the snapshot is complete?

snapmirror resume
snapmirror resume
snapmirror quiesce-q
snapmirror quiesce-q
options snapmirror.log enable off
options snapmirror.log enable off
snapmirror restart
snapmirror restart
Suggested answer: A
asked 23/09/2024
Ramesh Kumar Patel
38 questions

Question 112

Report Export Collapse

Exhibit:

Network Appliance NS0-163 image Question 112 78961 09232024011612000000

To remove a cluster setup, you must perform the steps displayed in the exhibit.

True
True
False
False
Suggested answer: A
asked 23/09/2024
Rambo Jhon
43 questions

Question 113

Report Export Collapse

Which one of the following statements apply to the Free Space Estimator utility?

This utility determines if there is sufficient space on the secondary volume to perform a transfer
This utility determines if there is sufficient space on the secondary volume to perform a transfer
This utility determines if there is sufficient disk space available on the primary to perform an OSSV transfer
This utility determines if there is sufficient disk space available on the primary to perform an OSSV transfer
This utility runs automatically after each transfer
This utility runs automatically after each transfer
This utility must be enabled on the secondary storage system
This utility must be enabled on the secondary storage system
Suggested answer: B
asked 23/09/2024
ALBERTO BONATO
49 questions

Question 114

Report Export Collapse

You have connected all cables and disk shelves in a Fabric Attached MetroCluster. Which one of the following commands would you use to verify that disks are connected and have dual paths?

storage show disk-p
storage show disk-p
sysconfig -v
sysconfig -v
vol status -r
vol status -r
disk show
disk show
Suggested answer: A
asked 23/09/2024
justen layne
43 questions

Question 115

Report Export Collapse

A mirrored volume has a failed disk, but there are no available spares in the pool from which the degraded plex was built. Data ONTAP will:

Choose spare disks to reconstruct from the opposite pool
Choose spare disks to reconstruct from the opposite pool
Warn you that there are no available spares from the proper pool
Warn you that there are no available spares from the proper pool
'Halt' after 24 hours if spare disks are not added to the proper pool
'Halt' after 24 hours if spare disks are not added to the proper pool
Stop all applications that are running
Stop all applications that are running
Suggested answer: B
asked 23/09/2024
Paul Macinic
36 questions

Question 116

Report Export Collapse

Which one of the following options will allow a snapmirror storage appliance to mirror from this system?

snapmirror. destination <destination_filer>
snapmirror. destination <destination_filer>
options snapmirror.allow<destination_filer>
options snapmirror.allow<destination_filer>
snapmirror.access <destination_filer>
snapmirror.access <destination_filer>
options snapmirror.access host = <destination_filer>
options snapmirror.access host = <destination_filer>
Suggested answer: D
asked 23/09/2024
HNO Oo
42 questions

Question 117

Report Export Collapse

You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is

powered on and accessible.
powered on and accessible.
fenced off manually.
fenced off manually.
Powered off and inaccessible.
Powered off and inaccessible.
in a giveback mode.
in a giveback mode.
Suggested answer: C
asked 23/09/2024
long tran
39 questions

Question 118

Report Export Collapse

What is the maximum distance between a standard clustered pair?

10 meters
10 meters
50 meters
50 meters
100 meters
100 meters
500 meters
500 meters
Suggested answer: D
asked 23/09/2024
Ahti Paju
37 questions

Question 119

Report Export Collapse

You want to create an automated test environment that performs a single file SnapRestore. Every time you run the procedure, however, SnapRestore prompts you to confirm your decision to revert the file. How can you automate this step?

Enter the priv set advanced mode on the storage appliance and the prompt will not appear.
Enter the priv set advanced mode on the storage appliance and the prompt will not appear.
Enable the options snaprestore_noprompts enable=on option.
Enable the options snaprestore_noprompts enable=on option.
Use the -f option with the snap restore command.
Use the -f option with the snap restore command.
These prompts are for data protection and auditing and cannot be overridden.
These prompts are for data protection and auditing and cannot be overridden.
Suggested answer: C
asked 23/09/2024
ERIK BURDETT
47 questions

Question 120

Report Export Collapse

In a synchronous SnapMirror configuration, the soui'ce storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.Which one of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:

outstandine=3s
outstandine=3s
visibility interval=3s
visibility interval=3s
cksum=3s
cksum=3s
src con=3
src con=3
Suggested answer: A
asked 23/09/2024
Mary Andreou
49 questions
Total 243 questions
Go to page: of 25
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

What is the minimum number of HA pairs required for Epsilon to be automatically assigned?
What is the format for snapvault schedule?
Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?
Which two types of Restore does Cloud Backup allow? (Choose two.)
When configuring SyncMirror disk pools, which platforms require disks connected to particular ports and/or FC adapters on particular ports?
To restore a qtree protected with SnapVault from the secondary storage system to the primary storage system, you can ______________. (Choose two.)
Identify the two commands that could be entered on a system with a SnapMirror source. (Choose two.)
Which two commands could be used if the cf giveback command foils? (Choose 2)
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
Open System SnapVault agents can be installed on all non-Network Appliance platforms.