Home / Network Appliance / NS0-163

Network Appliance NS0-163 Practice Test - Questions Answers, Page 4

Question list

List of questions

Question 31

(0)

When using MetroCluster, identify two methods for restricting access to the disaster site node. (Choose 2)

Question 32

(0)

When you create a restricted volume to be used as the destination for SnapMirror data replication, which command allows you to check the size of the source and destination volumes?

Question 33

(0)

Which two supported methods would you use to restore data from a SnapVault for NetBackup Volume?

Question 34

(0)

The snapvault snap sched-x command can be used to:

Question 35

(0)

When you are setting up SnapMirror, which one of the following is not a replication pre-requisite?

Question 36

(0)

Which three are true when creating a SyncMirror volume? (Choose 3)

Question 37

(0)

If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank

Question 38

(0)

Which command displays the disk ownership for both CPU modules in a FAS270C appliance?

Question 39

(0)

You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which one of the following is the most likely explana

Question 40

(0)

Which one of the following actions will cause a currently in sync snapmirror relationship to fall out of sync?

Question 31

When using MetroCluster, identify two methods for restricting access to the disaster site node. (Choose 2)

Use manual fencing

Turn off power to the disaster site node.

Use the cf forcetakeover-d command.

Use the cfgiveback-f command.

Show Answer Comment (0)

Question 32

When you create a restricted volume to be used as the destination for SnapMirror data replication, which command allows you to check the size of the source and destination volumes?

sysconfig -v

vol status -b

vol mirror --v

Show Answer Comment (0)

Question 33

Which two supported methods would you use to restore data from a SnapVault for NetBackup Volume?

Use the NetBackup Administration Console

Use drag-and-drop technologies

Use the snapvault restore Data ONTAP command

Use the SnapRestore Data ONTAP service

Show Answer Comment (0)

Question 34

The snapvault snap sched-x command can be used to:

Schedule full backups

Start initial backups

Schedule incremental backups

Specify platforms that can be backed up

Show Answer Comment (0)

Question 35

When you are setting up SnapMirror, which one of the following is not a replication pre-requisite?

SnapMirror must be licensed for each storage appliance.

The source volume must be offline.

If you are replicating a volume, you must create a restricted volume to be used as the SnapMirror destination volume.

The capacity of the SnapMirror destination must be greater than or equal to the capacity of the source.

Show Answer Comment (0)

Question 36

Which three are true when creating a SyncMirror volume? (Choose 3)

The number of disks added must be an even number and equally divided between the two plexes.

The disks selected for Plex 0 and Plex 1 must come from the same disk pools.

The number of disks selected for one plex must equal the number of disks selected from the other plex.

The disks are selected first on the basis of equivalent bytes per sector (bps) size, then on the basis of the size of the disk. If there is no equivalent-sized disk, Data ONTAP takes a larger capacity disk and downsizes it.

Show Answer Comment (0)

Question 37

If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank

Show Answer Comment (0)

Question 38

Which command displays the disk ownership for both CPU modules in a FAS270C appliance?

disk show-v

disk display-r

disk own -s

vol status --r

Show Answer Comment (0)

Question 39

You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which one of the following is the most likely explanation?

You must recreate the directory structure before trying to restore the file.

Once the directory structure has been deleted, you cannot restore the file using single file SnapRestore. You must now SnapRestore the volume.

Snapshots have been created since the original directory structure was deleted.

None of the above

Show Answer Comment (0)