Home / Network Appliance / NS0-593

Network Appliance NS0-593 Practice Test - Questions Answers, Page 2

Question list

List of questions

Question 11

(0)

A customer enabled NFSv4.0 on an SVM and changed the client mount from NFSv3 to NFSv4. Afterwards, the customer found that the directory owner was changed from root to nobody. In this scenario, wh

Question 12

(0)

You have a NetApp ONTAP cluster consisting of four NetApp FAS8200 controllers with two NetApp CN1610 cluster switches running ONIAP 9.8 software. You are receiving several alert messages stating tha

Question 13

(0)

Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Lin

Question 14

(0)

You have a customer complaining of long build times from their NetApp ONTAP-based datastores. They provided you packet traces from the controller and client. Analysis of these traces shows an avera

Question 15

(0)

Your customer wants to access a LUN on a FAS 8300 system from a VMware ESXi server through the FC protocol. They already created a new SVM, volume. LUN, and igroup for this purpose. The customer rep

Question 16

(0)

You recently discovered the error message shown below in your ONTAP logs. What should be your first action to correct this Issue?

Question 17

(0)

When an administrator tries to create a share for an existing volume named voll, the process fails with an error. Referring to the exhibit, what Is the reason for the error?

Question 18

(0)

The motherboard of Node-01 is being replaced. To perform this task, a takeover was Initiated from Node-02. Node-02 panics showing the string below. PANIC; Permanent errors on all HA mailbox disks (

Question 19

(0)

You are deploying NetApp ONTAP Select. When trying to add VMware vCenter to the inventory, you receive the message shown below. Credential authentication failed for x.x.x.x with: HostConnectionFail

Question 20

(0)

You created a new NetApp ONTAP FlexGroup volume spanning six nodes and 12 aggregates with a total size of 4 TB. You added millions of files to the FlexGroup volume with a flat directory structure to

Question 11

A customer enabled NFSv4.0 on an SVM and changed the client mount from NFSv3 to NFSv4.

Afterwards, the customer found that the directory owner was changed from root to nobody.

In this scenario, which statement is true?

The customer did not configure name services on the SVM.

The clients must be restarted to start using NFSv4.

The export policy is not configured properly.

The ID mapping domains do not match between the client and server.

Show Answer Comment (0)

You have a NetApp ONTAP cluster consisting of four NetApp FAS8200 controllers with two NetApp CN1610 cluster switches running ONIAP 9.8 software. You are receiving several alert messages stating that the cluster network has degraded. After troubleshooting, you determine that the errors are being generated from Node 2, interface e0b.

In this scenario, what should you do first to solve this problem?

Replace the Twinax cable between Node 2, Interface e0b. and the NetApp CN1610 switch.

Replace the motherboard on Node 2.

Replace both NetApp CN1610 switches.

Replace the NetApp CN1610 switch that connects to Node 2, interface e0b.

Show Answer Comment (0)

Question 13

Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Linux client and the broadcast domain on the NetApp ONTAP 9.8 cluster.

Referring to the exhibit, which ONTAP command will help isolate a possible MTU mismatch?

Show Answer Comment (0)

Question 14

You have a customer complaining of long build times from their NetApp ONTAP-based datastores.

They provided you packet traces from the controller and client. Analysis of these traces shows an average service response time of 1 ms. QoS output confirms the same. The client traces are reporting an average of 15 ms in the same time period.

In this situation, what would be your next step?

The cluster is responding slowly and requires further investigation using performance archives.

The client that reports high latency should be investigated.

The cluster interconnects should be investigated.

A sync core should be triggered.

Show Answer Comment (0)

Question 15

Your customer wants to access a LUN on a FAS 8300 system from a VMware ESXi server through the FC protocol. They already created a new SVM, volume. LUN, and igroup for this purpose. The customer reports that the server's FC HBA port Is online, but the LUN does not show up.

Referring to the exhibit, what is the reason for this problem?

The FC service has not been configured on the SVM.

The zoning on the FC switches Is Incorrect.

The LUN Is not mapped to the correct SCSI ID.

The esxserver igroup contains incorrect IQNs.

Show Answer Comment (0)

Question 16

You recently discovered the error message shown below in your ONTAP logs.

What should be your first action to correct this Issue?

Power cycle all the disk storage shelves that contain drives of the aggregate with the my_data_vol volume.

Determine the root cause behind the inconsistency before attempting any recovery procedure.

Use the storage takeover command on the storage controller that contains my_data_vol.

Use the wafliron command against my_data_vol to solve the inconsistency on the volume.

Show Answer Comment (0)

Question 17

When an administrator tries to create a share for an existing volume named voll, the process fails with an error.

Referring to the exhibit, what Is the reason for the error?

The volume must have a type of DP.

The volume has not been mounted.

The CIFS service is not authenticating properly with the domain controller.

The CIFS service is not in workgroup mode.

Show Answer Comment (0)

Question 18

The motherboard of Node-01 is being replaced. To perform this task, a takeover was Initiated from Node-02. Node-02 panics showing the string below.

PANIC; Permanent errors on all HA mailbox disks (while marshalling header) in SKprocess fnmbx_instanceWorker on release 9.5P8 (C) What has happened in this situation?

While in maintenance mode, the sldiag device show command was executed.

While in maintenance mode, the fcadmin device_map command was executed.

While in maintenance mode, the HA_config show command was executed.

While in maintenance mode, the mailbox destroy local command was executed.

Show Answer Comment (0)

Question 19

You are deploying NetApp ONTAP Select. When trying to add VMware vCenter to the inventory, you receive the message shown below.

Credential authentication failed for x.x.x.x with: HostConnectionFailed In this scenario, how would you correct this problem?

Change the vCenter password.

Change the IP address of the ONTAP Select Deploy VM.

Change the gateway address of the ONTAP Select Deploy VM.

Change the IP address of the vCenter server.

Show Answer Comment (0)

Question 20

You created a new NetApp ONTAP FlexGroup volume spanning six nodes and 12 aggregates with a total size of 4 TB. You added millions of files to the FlexGroup volume with a flat directory structure totaling 2 TB, and you receive an out of apace error message on your host.

What would cause this error?

The maximum number of volume constituents has been reached in the ONTAP software.

All constituent volumes are full.

The inode limit is exceeded in the ONTAP software.

The maxdirsize Is exceeded in the ONTAP software.

Show Answer Comment (0)

Total 60 questions