ExamGecko
Home / Network Appliance / NS0-593 / List of questions
Ask Question

Network Appliance NS0-593 Practice Test - Questions Answers, Page 4

Add to Whishlist

List of questions

Question 31

Report Export Collapse

You have connection Issues from a Linux host to an AFF A400 FC LUN. You are asked by support to run the NetApp sanlun command to provide troubleshooting information.

Which NetApp software package must be installed on the host?

Virtual Storage Console
Virtual Storage Console
Inventory Collect Tool
Inventory Collect Tool
Host Utilities package
Host Utilities package
SnapDrive for UNIX
SnapDrive for UNIX
Suggested answer: C
asked 23/09/2024
Haleem SHITOU OGUNGBEMI
45 questions

Question 32

Report Export Collapse

After a normal power down of both nodes for building maintenance, Node01 of a 2-node cluster cannot be powered back up; however, all disk shelves are powered.

Which action should be performed to bring the cluster online and allow Node02 to serve data?

Recreate the cluster with the system configuration recovery cluster recreate -from node command.
Recreate the cluster with the system configuration recovery cluster recreate -from node command.
Reboot the node With the system node reboot -node Node02 -bypass-optimization true command.
Reboot the node With the system node reboot -node Node02 -bypass-optimization true command.
Perform a takeover with the storage failover takeover -ofnode Node01 -option force command.
Perform a takeover with the storage failover takeover -ofnode Node01 -option force command.
Reinitialize the cluster with option 4a from the boot menu.
Reinitialize the cluster with option 4a from the boot menu.
Suggested answer: A
asked 23/09/2024
Duncan Brundseaux
44 questions

Question 33

Report Export Collapse

A system panic due to an "L2 watchdog timeout hard reset" error occurred. You have found a FIFO message in the SP log.

Which FIFO message Is useful for Investigating this Issue?

before NMI BBSP:C=00 L=00 FIFO: F3 F2 F1 F0 5 B2 0 0 0 80 20 E F E3 C0 C2 3 4 6 7 9 9 AB . BIOS exit BBSP:C=2F L=20 FIFO: 2 C8 C9 C4 24 4 6 18 7 8 11
before NMI BBSP:C=00 L=00 FIFO: F3 F2 F1 F0 5 B2 0 0 0 80 20 E F E3 C0 C2 3 4 6 7 9 9 AB . BIOS exit BBSP:C=2F L=20 FIFO: 2 C8 C9 C4 24 4 6 18 7 8 11
before Reset BBSP:C=00 L=00 FIFO:
before Reset BBSP:C=00 L=00 FIFO:
ONTAP Shutdown BBSP:C=00 L=2F FIFO:
ONTAP Shutdown BBSP:C=00 L=2F FIFO:
Suggested answer: B
asked 23/09/2024
Grégory CALIX
40 questions

Question 34

Report Export Collapse

An administrator receives the following error message:

Network Appliance NS0-593 image Question 34 79886 09232024011803000000

What are two causes for this error? (Choose two.)

There Is excessive SSD load causing the wear leveling to become unbalanced.
There Is excessive SSD load causing the wear leveling to become unbalanced.
A disk is falling.
A disk is falling.
There is excessive SATA HDD load.
There is excessive SATA HDD load.
An SSD disk is performing garbage collection to create a dense data layout.
An SSD disk is performing garbage collection to create a dense data layout.
Suggested answer: A, C
asked 23/09/2024
Maria Gervasi
41 questions

Question 35

Report Export Collapse

After expanding a two-node AFF A300 cluster with two AFF A700 nodes, you observe latencies when data is accessed indirectly. The system node run -node -command netstat command shows retransmits and packet drops on the LIFs.

The AFF A700 nodes with 40 Gbps and the AFF A300 connect with 10 Gbps to the cluster interconnect. You are using Cisco Nexus 3132Q cluster interconnect switches. You just updated to ONTAP 9.8 software.

In this scenario, what is causing this problem?

The 10 Gbps to 10 Gbps cluster Interconnect is creating a speed mismatch.
The 10 Gbps to 10 Gbps cluster Interconnect is creating a speed mismatch.
AFF A300 and AFF A700 node mixing Is not supported in ONTAP 9.8 software.
AFF A300 and AFF A700 node mixing Is not supported in ONTAP 9.8 software.
The AFF A300 Is using an adapter card for the cluster Interconnect, but only onboard ports are supported.
The AFF A300 Is using an adapter card for the cluster Interconnect, but only onboard ports are supported.
There is an NXOS firmware mismatch, verify in the Interoperability Matrix (1MTJ for a supported version.
There is an NXOS firmware mismatch, verify in the Interoperability Matrix (1MTJ for a supported version.
Suggested answer: A
asked 23/09/2024
Brent Kehoe
38 questions

Question 36

Report Export Collapse

Which two throughput elements are controlled by host applications? (Choose two.)

Become a Premium Member for full access
  Unlock Premium Member

Question 37

Report Export Collapse

A 2-node cluster hosts only NAS data UFs. All nodes lose access to the cluster network.

Network Appliance NS0-593 image Question 37 79889 09232024011803000000

Referring to the exhibit, which statement is correct?

Become a Premium Member for full access
  Unlock Premium Member

Question 38

Report Export Collapse

Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP for Azure HA solution is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why. No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.

In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is working properly? {Choose two.)

Become a Premium Member for full access
  Unlock Premium Member

Question 39

Report Export Collapse

You want to assign storage access to an NVMe protocol host.

Which three objects must be configured to accomplish this task? (Choose three.)

Become a Premium Member for full access
  Unlock Premium Member

Question 40

Report Export Collapse

You receive the "Unable to connect to the management gateway server" error when trying to connect to a node management IP.

In this situation, how do you determine whether core dumps are generated for the mgwd user space process?

Become a Premium Member for full access
  Unlock Premium Member
Total 60 questions
Go to page: of 6
Search

Related questions