CompTIA SK0-005 Practice Test - Questions Answers, Page 18

Open-source software is software that is freely available and can be modified and distributed by anyone. It usually requires very little technical support and has no licensing fees. Therefore, it would be the lowest cost solution for an application that does not need much support. Reference:

https://www.comptia.org/training/resources/exam-objectives/comptia-server-sk0-005-examobjectives (Objective 2.3)

The HCL stands for Hardware Compatibility List and it is a list of hardware devices that are tested and certified to work with a specific operating system. If a network card is not on the HCL for the OS, it may not function properly or cause compatibility issues. Therefore, verifying the network card is on the HCL for the OS should be the next step to troubleshoot this issue. Reference:

https://www.comptia.org/training/resources/exam-objectives/comptia-server-sk0-005-examobjectives (Objective 4.1)

A server baseline is a set of metrics that represents the normal performance and behavior of a server under a specific workload and configuration. A server baseline can help answer the server performance question by comparing the current performance with the previous performance before the upgrade. This can help identify any changes or issues that may have affected the server performance. Reference: https://www.comptia.org/training/resources/exam-objectives/comptiaserver- sk0-005-exam-objectives (Objective 4.2)

To calculate the minimum number of disks needed for this application, we need to consider the RAID levels and their disk requirements. RAID 1 requires a minimum of two disks and provides mirroring, which means that data is duplicated on both disks. RAID 5 requires a minimum of three disks and provides striping with parity, which means that data is distributed across all disks with one disk storing parity information for error correction. RAID 5 can tolerate one disk failure without losing data. To create a 10GB RAID 1 array for log files, we need two 10GB disks. To create a 20GB RAID 5 array for data files, we need four 10GB disks (three for data and one for parity). To create a 20GB RAID 5 array for the operating system, we need another four 10GB disks (three for data and one for parity). Therefore, the total number of disks needed is 2 + 4 + 4 = 10. However, since we can use different RAID levels for different partitions on the same disk, we can optimize the disk usage by using only eight disks as follows: Disk 1: 10GB RAID 1 (log files) + 10GB RAID 5 (data files) Disk 2:

10GB RAID 1 (log files) + 10GB RAID 5 (data files) Disk 3: 10GB RAID 5 (data files) + 10GB RAID 5 (OS) Disk 4: 10GB RAID 5 (data files) + 10GB RAID 5 (OS) Disk 5: 10GB RAID 5 (parity for data files) + 10GB RAID 5 (OS) Disk 6: 10GB RAID 5 (OS) + unused space Disk 7: 10GB RAID 5 (parity for OS) + unused space Disk 8: unused space Reference: https://en.wikipedia.org/wiki/Standard_RAID_levels

A DR site is a backup site that can be used to restore business operations in case of a disaster that affects the primary site. A warm site is a DR site that has some equipment and data ready to be activated quickly, but not as fast as a hot site that has fully operational systems and data. A cold site is a DR site that has only basic infrastructure and no equipment or data. The location of a DR site is an important factor to consider when designing and implementing a DR plan. A DR site that is too close to the primary site may be affected by the same disaster, such as a power outage, a flood, or an earthquake. A DR site that is too far away from the primary site may incur higher costs and latency issues. Therefore, a good practice is to set up a DR site that is geographically located in another region that has different risk factors and environmental conditions than the primary site. This can help ensure that the DR site is available and accessible when needed. Reference:

https://www.comptia.org/training/resources/exam-objectives/comptia-server-sk0-005-examobjectives (Objective 3.3)

Shipping is a process of sending logs from one system to another system for centralized storage and analysis. Shipping can help ensure compliance with regulations that require financial systems logs to be stored in a central location. Shipping can also help improve security, performance, and scalability of log management. Reference: https://www.comptia.org/training/resources/examobjectives/ comptia-server-sk0-005-exam-objectives (Objective 3.4)

DLP stands for Data Loss Prevention and it is a system that scans outgoing email for account numbers, sensitive phrases, and other forms of PII (Personally Identifiable Information). DLP can help prevent data breaches, comply with regulations, and protect the privacy of customers and employees. DLP can also block, encrypt, or quarantine emails that contain sensitive data. Reference:

https://www.comptia.org/training/resources/exam-objectives/comptia-server-sk0-005-examobjectives (Objective 3.2)

netstat is a command-line tool that displays network connections, routing tables, interface statistics, and more. The -a option shows all listening and non-listening sockets on the server. This can help check the open ports on a server and identify any unwanted or malicious connections. Reference:

https://docs.microsoft.com/en-us/windows-server/administration/windows-commands/netstat

1U stands for one unit and it is a standard unit of measurement for rack-mounted servers. It is equal to 1.75 inches (4.45 cm) in height. A 42U rack can accommodate 42 1U servers or a combination of servers with different unit sizes. Therefore, the unit size per server should be 1U if there are 19 1U servers in a 42U rack. Reference: https://www.comptia.org/training/resources/examobjectives/ comptia-server-sk0-005-exam-objectives (Objective 1.2)