Refer to the exhibit. A Cisco engineer is configuring a FlexPod data center for SAP with Cisco ACI, Cisco UCS Manager 4.0. and Net AppAFFA-Series. All systems and fabric links feature redundancy and provide end-to-end high availability. After the engineer sets the needed VLANs on the NetApp controller ports and adds them to the data broadcast domain, the engineer must make the storage disks visible for the UCS hosts Which action must be taken on the UCS to accomplish this task?

Configure ION pools for ISCSI boot.

Provide a storage virtual machine.

Enable HTTPS access on the servers.

Which two paths are provided by deploying an OOB management network in a data center that uses Cisco Nexus switches? (Choose two.)

Layer 3 for monitoring purposes

Layer 3 for vPC keepalive packets

Layer 3 for monitoring purposes

Layer 3 for vPC keepalive packets

Refer to the exhibit. A Cisco engineer is configuring a Cisco UCS integrated infrastructure for SAP HANA that consists of 8 x Cisco UCS B/C480-M5 servers for SAP HAN A and 4 x Cisco UCS C240-M5 C-Series rack mount servers for storage. The rack servers are equipped with Cisco VIC 1225T. The engineer plans to install RHEL8. but the boot process is interrupted at installation because the iSCSl LUNs are not recognized by the VIC adapter. After proper Investigation, the engineer concludes that the initiator and target configuration that is programmed on the primary ISCSl VNIC to the operating system Is missing. What is the reason for the issue?

The storage system is not reachable

The network interfaces are not configured.

The Linux ISO image is not Cisco approved.

The boot parameter lp=ibft is not set.

The storage system is not reachable

Refer to the exhibit. Refer to the exhibit. An engineer deployed a VXLAN fabric with this configuration:* interface VLAN 100 on VTEP1 with no IP address* interface VLAN 200 on VTEP4 with no IP addressWhich set of actions must the engineer take to ensure that host A communicates with host B?

Associate VNI 20000 to VRF Web on VTEP1. Associate VNI 10000 to VRF Application on VTEP1.

Associate VN110000 to VRF Application on VTEP4. Associate VNI 20000 lo VRF Web on VTEP1.

Associate VN110000 to VRF Web on VTEP4. Associate VNI 10000 to VRF Application on VTEP1.

Associate VNI 20000 to VRF Application on VTEP1. Associate VNI 20000 to VRF Web on VTEP1.

Associate VNI 20000 to VRF Web on VTEP1. Associate VNI 10000 to VRF Application on VTEP1.

Refer to the exhibit During a synchronization of port rotes, a device receives a proposal message on one of its ports that is selected as the new root port. The logs show that Rapid PVST+forced all other ports to synchronize with the new loot information. The engineer analyzes the port stales and concludes that the device is synchronized with superior root information received on the root port, and all other ports are synchronized. What happens to a designated port that is in the forwarding state and is not configured as an edge port, if Rapid PVST+ forces it to synchronize with new root information?

It transitions to the Mocking state

It does not receive BPDUs for transmission.

IT immediately replies with its own information.

It discards frames switched from another port.

It transitions to the Mocking state

Refer to the exhibit. Refer to the exhibit. A Cisco engineer is implementing a customer data center design and must configure Cisco MDS 9000 Series Switches. The configuration has the required IP addresses on each SAN. The requirement is that each FCIP is a separate E(ISL). and the FCIP links must connect to different switches across the two SAN islands. Also, the Fibre Channel traffic is to be load-balanced across the FCIP link. After the engineer configures the FCIP profiles and interfaces they want to enable QoS for the link. Which types of values are needed for the DSCP to mark the IP packets?

retransmit and keepalive timeout

Which orchestration tool must be used to manage VXLAN fabrics and includes a built-in dashboard and real-time network health summary for managed devices?

Cisco Nexus Dashboard Fabric Controller

Refer to the exhibit. Refer to the exhibit. A Cisco engineer is planning a data migration job in heterogeneous SANs where the existing and new storage devices for the migration are already connected to the MDS switches. All paths from the SSM to the storage-connected switch are going through the Cisco fabric. The setup is with active/active arrays and multiple LUN sets. What is the best approach to copy the LUN sets to the new location?

Create two data migration jobs, and add two storage pons in each job.

Enable synchronous replication for the new storage array.

Add all paths Fabric-A zones to Fabric-B zones.

Create two data migration jobs, and add two storage pons in each job.

Grant access to all servers to the existing data sets.

An engineer must design the compute portion of a data center environment. The environment includes:* direct-attach Fibre Channel storage array with four 32 G Fibre Channel ports per controller* Cisco UCS B-series servers equipped with Cisco UCS IOM 2408 Fabric Extenders* Cisco 6454 Fabric InterconnectsThe fabric interconnects conned to the LAN via 100G ports, the SAN via 32 G Fibre Channel ports, and the IOM 2408 via 10 G ports. Which storage connectivity strategy must the engineer choose?

* UCS: four-poll Port Channel from each IOM to each fabric interconnect * Storage; tour-port SAN-PortChannel from each SAN controller to each fabric interconnect

UCS' two-port PortChannel from each IOM10 each fabric interconnect. * Storage: Qty four Fibre Channel links from each SAN controller Id each fabric interconnect.

* UCS: four-poll Port Channel from each IOM to each fabric interconnect * Storage; tour-port SAN-PortChannel from each SAN controller to each fabric interconnect

* UCS: Qty (our 802.1q trunks from each IOM to each fabric interconnect * Storage: Qfy two Fibre Channel links from each SAN controller to each fabric Interconnect

* UCS; four-port back-to-baok PortChannel between IOM and fabric interconnect * Storage; two-port SAN-PortChannel from each SAN controller to each fabric interconnect

Refer to the exhibit A Cisco engineer is configuring Cisco Nexus 7000 Series Switches. To simplify initial configuration verification and vPC+/HSRP troubleshooting, the engineer configures the primary vPC+ peer device with the FHRP active router highest priority. The primary FHRP device responds to ARP requests, even though the secondary vPC+ device also forwards the data traffic. Which configuration enables the Layer 3 connectivity from each vPC* peer device?

Ensure that the enhanced Layer 2 license has been installed.

Configure a VLAN network interlace for the same VLAN from both devices.

Ensure that the enhanced Layer 2 license has been installed.

Manually configure virtual MAC addresses tor any FHRP protocol.

Set a restore timer that delays the vPC+ restart.

An engineer is designing a Cisco UCS Central implementation for an existing Cisco UCS infrastructure, and the current policies must be reused. Which action must the engineer select?

Connect Cisco UCS Manager to Cisco UCS Central and convert local policies to global policies.

Export the policies from Cisco UCS Manager and import them in Cisco UCS Central.

Connect Cisco UCS Manager to Cisco UCS Central and convert local policies to global policies.

Create new policies in Cisco UCS Central and change the assignment to central.

Retain existing policies in Cisco UCS Manager and use global policies for new service profiles

An engineer deploys a Cisco UCS environment with the storage array directly attached to the Fabric Interconnects. The operations team mandates that the solution must not require the configuration of Fibre Channel zoning. Which configuration set meets these requirements?

Storage facing port type: Storage port Fabric interconnect FC mode: Switching

Storage lacing port type: Uplink port Fabric interconnect FC mode: End-host

Storage facing port type: Storage port Fabric interconnect FC mode: Switching

Storage facing port type: FCoE storage port Fabric interconnect FC mode: End-host

Storage facing port type: Appliance port Fabric interconnect FC mode: Switching

To help automate the vHBA configuration process, a network engineer is configuring vHBA template pairs on UCS. The engineer is creating primary and secondary templates to define how vHBAs on a server connect to the SAN. Which fact about the template pair should the engineer consider for its potential impact on service?

The WWPN pool configuration will not be shared between the two templates.

The description configuration will be shared between the two templates.

The WWPN pool configuration will not be shared between the two templates.

The fabric ID configuration will be shared between the two templates.

The QoS policy configuration will not be shared between the two templates.

An engineer must connect a Cisco UCS Fabric Interconnect to a storage array using a Fibre Channel protocol. The SAN must be directly connected to the UCS fabric interconnects using ports 1/1 and 1/2. Which fabric interconnect configuration must be used?

Fibre Channel end-host mode, and ports as Fibre Channel storage port

Ftore Channel switching mode, and ports as Fibre Channel storage port

Fibre Channel end-host mode, and ports as Fibre Channel uplink port

Fibre Channel switching mode, and ports as Fibre Channel uplink port

A network engineer designs a virtual network in a Cisco UCS Manager. The traffic must be explicitly forwarded from the vNIC on the server to a specific uplink Ethernet port on the Cisco fabric interconnect. Also, the server vNIC must use the same uplink Ethernet port after reboot. Finally, the design requires a OoS policy for remote direct memory access over converged Ethernet (RoCE v2). Which set of design features meets these requirements?

LAN pin group and Platinum priority

vNIC template and Gold priority

server VLAN pool and Gold priority

LAN pin group and Platinum priority

Refer to the exhibit. Fiber links are provisioned directly between the spine and leaf switches in the given LAN topology A/30 prefix has been configured over each fiber link to provide underlay connectivity for a VXLAN network. The network-engineering team must update the network configuration to provide the shortest possible convergence time if a fiber link is cut. Which action must the team take to meet the requirement?

Configure the /30 links as OSPF point-to-point networks

Configure ECMP on the /30 links

A midsize corporation with significant data-storage requirements is planning to deploy RFC 3720-based technology in its data center to provide efficient and reliable block-level storage access to servers The corporation requires a robust solution with optimal performance, load-balancing, and fault tolerance. The solution must use multiple network paths to optimize bandwidth usage and provide redundancy LACP has already been enabled on the data-center switches Which two actions must be taken to accomplish the goal? (Choose two.)Implement VLAN tagging in accordance with the IEEE 802.10 standard to segregate iSCSI traffic from other data-center traffic

Configure iSCSI MPIO software on the hosts

Configure the iSCSI initiators and targets to use a single network path

Disable jumbo frames on the data center switches

Implement MPIO with redundant network paths

Configure iSCSI MPIO software on the hosts

Configure the iSCSI initiators and targets to use a single network path

A Cisco engineer is analyzing a customer environment where dozens of VMs are running on a physical server and UCS chassis are cascaded The setup uses two ISLs in a port channel to the SAN switch (per fabric) The oversubscription from VM to physical SAN port is often 20 (VMs/host) x 72 (9 UCS chassis cascaded = 72 hosts): 2 (ISLs from fabric interconnect to SAN switch port on the NPV core (NPIV enabled switch) This results to 20 x 72 2 per single ISL = 720 VMs per ISL20 (VMs per host) x 8 (hosts per chassis) x 9 (chassis per port channel to SAN switch) / 2 (ISLs per port channel) = 20 x 8 x 9 / 2 = 720 VMs per SAN F-port What is the best way to resolve possible IOPS bottleneck?

Configure 802 1Qbb priority flow control

Deploy a content delivery network

Enable Windows 1Gb server full duplex

Configure 802 1Qbb priority flow control

Remove data encryption on the SSD

A network architect is designing a storage network to connect to an existing IP network over 100G Ethernet ports for multiple hosts The architect decided to require iSCSI multipathmg to provide multiple routes between servers within the SAN and storage devices that reside within the IP network. Which requirement must be applied to the IP network switch that connects to the SAN environment where the hosts reside9

ECMP routes on the IP network to facilitate toad sharing

VLAN load balancing to the storage devices

multiple physical connections to the iSCSI SAN device

trunk configuration toward the iSCSI SAN device for multiple VLANs

Refer to the exhibit. Refer to the exhibit. A network engineer must improve high availability within the given UCS infrastructure The engineer configured central nodes A and B in cluster mode to ensure that traffic fails over in the case of a network outage. Which type of redundancy will the cluster configuration provide?

redundancy for the management, control, and data planes

redundancy for the management plane only

redundancy via a single fabric interconnect

redundancy for the management, control, and data planes

link-level redundancy via one management port

A large financial institution hosts all customer data in a critical data center with a single physical location Top management is concerned about the risk of a single-site failure. Dot budget is also an issue, so the network engineering team is working to implement a cost-effective redundancy strategy with a second data center. The new data center must use a three-tier design Identical to the existing data center. Business requirements dictate that all data must always be accessible from anywhere in the world, even It a single site fails. The team purchased two Cisco Nexus 7700 Series Switches and four Catalyst 8000 Series Routers. Which action must the team take to accomplish the goal?

Implement OTV with the Nexus 7700 Series devices to extend Layer 2 connectivity between the two data centers and provide disaster-recovery capabilities.

Implement NVGRE on the Catalyst 8000 routers to create a DCI communication channel between the data centers and provide Layer 2 extension capabilities.

Implement OTV with the Nexus 7700 Series devices to extend Layer 2 connectivity between the two data centers and provide disaster-recovery capabilities.

Implement FabricPath on the Catalyst 8000 routers in both data centers to provide full redundancy in the event of a disaster.

Implement HSRP with the Nexus 7700 Series devices to provide gateway redundancy to ensure seamless failover between the Nexus switches.

Refer to the exhibit. FCoE is used in the topology between the SAN Storage devices and SAN-Core routers. After noticing traffic drops to hosts accessing SAN-B storage, the engineering team wants to reduce the oversubscription ratio in the topology. Which action must the team take?

Increase the bandwidth between the SAN-Coro and SAN-Edgo devices.

Increase the bandwidth between SAN-A and SAN-B Storage toward the SAN-Core devices.

Configure QoS to prioritize SAN-A traffic

Configure QoS to prioritize SAN-B traffic.

Increase the bandwidth between the SAN-Coro and SAN-Edgo devices.

A Cisco engineer is using a PowerShell script to create a service profile template on Cisco UCS Manager. After defining the server pools and other templates, the engineer must ensure that the hosts are visible lo the northbound SAN network and storage initiators. Which configuration must be applied to enable this capability?

Swwpn.pool | Add-UcsWwnMemberBlock -From 20:00:00:24: B5:00:00:00 -To 20:00:00:24: B5:00:00:09

Get-UcsApplianceCloud | Get-UcsVlan -name AppIianceVlan | Add-UcsVlanMemberPort -Switchld A -Slotld 1 -Portld 15

Get-UcsApplianceCloud | Get-UcsVlan -Name AppIianceVlan | Add-UcsVlanMemberPortChannel -Switchld A -Portld $ap_pc.Portld

Get-UcsMacPool -lies <handle or name> default | Add-UcsMacMemberBlock 00:25: B5: OO: A0:O0 00:25: B5:00:AO:08

Swwpn.pool | Add-UcsWwnMemberBlock -From 20:00:00:24: B5:00:00:00 -To 20:00:00:24: B5:00:00:09

Refer to the exhibit. Refer to the exhibit. An engineer must deploy NEW-VRF-001 in the data center. All hosts require full reachability with all other hosts, no matter on which pod the host deployment occurs. Which set of commands must the engineer include in the deployment?

advertise I2vpn evpn route-taraet both auto

host-reachability protocol bgp advertise I2vpn evpn

route-target both auto evpn route-target both auto

address-family I2vpn evpn route-target both auto

advertise I2vpn evpn route-taraet both auto

Cisco 300-610 Practice Test 6 - Free Online Exam Prep & Questions

An engineer must design a solution with storage reachability between too physical servers and a storage array. The storage array connectivity is to a SAN switch that Is limited to 46 ports. Which topology meets the requirements without adding more MOS switches?

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-610 Practice Test 6

Question

Cisco 300-610 Practice Tests

Practice Tests