The service provider is serving hosts with two different multicast streams from source X and source Y.Source X is multicast group 224.0.0.0/8, and source Y is multicast group 226.0.0.0/8. Multicast source X should send its stream through bidirectional RP address 10.20.1.1, and multicast source Y should send its stream through RP address10.20.2.1. Which configuration meets these requirements?

Add ip pim bidir-enable in global mode on RB.

Enable ip pim ssm default on RA and RB.

Add ip pim bidir-enable in global mode on RB.

Permit the source X and source Y IP addresses in the access list on RB.

Set PIM sparse mode with a static RP address of 10.20.2.1 on RA and RC.

Refer to Exhibit: A network engineer must update the routing toward the web server with IP address 35.22.13.1. The primary path must be configured via the neighbor router with ID 1.1.1.1. However, local-preference configuration is not permitted on R1.Which task must the engineer perform on R1 to complete the implementation?

Enable MED comparison between routes from neighbors in different AS.

Configure the device to choose the best MED from the same AS.

Set the device to ignore the conditional MED if the route originated in a different autonomous system.

Enable MED comparison between routes from neighbors in different AS.

Implement deterministic MED to choose the best route from the different AS.

Refer to the exhibit. An engineer with an employee 10:4350:47:853 is implementing IS-IS as the new routing protocol in the network. All routers in the network operate as Level 2 routers in the same private autonomous system, and the three branches are connected via dark fibre. The engineer has already implemented IS-IS on router R1 with NET address 49.0133.532b.ca14.6915.21311.F40F.1B3a.ba10.00. Which IS-IS NET address configuration must be implemented on R3 to establish IS-IS connectivity?

49.0133.532b.ca14.6915.21311.f40f.1b4a.bb87.00

49.0135.332b.ca14.6975.28371.1721.1b3b.ca11.10

48.0133.532b.ca14.6915.21311.f40f.1626.bb98.00

49.0133.532b.ca14.6915.21311.1721.1b4a.0013.01

How does Cisco MPLS TE use OSPF extensions to allow for optimized transit between a headend router and a destination router?

Opaque LSAs calculate and establish unidirectional tunnels that are set according to the network constraint.

Router LSAs share router link advertisements to each router within the MPLS environment so that tunnels can be built bidirectionally.

ASBR Summary LSAs share OSPF domain information so that the two routers know how to reach each other during tunnel setup.

Network LSAs share RSVP information to build the tunnel between the two routers.

Opaque LSAs calculate and establish unidirectional tunnels that are set according to the network constraint.

What are two features of 6RD IPv6 transition mechanism? (Choose two.)

It inserts IPv4 bits into an IPv6 delegated prefix.

It uses stateless automatic 6to4 tunnels between CE routers and the BR router.

It inserts IPv4 bits into an IPv6 delegated prefix.

It uses a native IPv6-routed network between CE routers and the BR router.

It allows dynamic 1:N translation of IPv6 address.

It uses stateful automatic 6to4 tunnels between CE routers and the BR router.

It uses stateless automatic 6to4 tunnels between CE routers and the BR router.

Refer to the exhibit. A network engineer is implementing an LDP-based MPLS solution to enable packet flow between the two bank sites The engineer was given two requirements* LDP peering must stay up when there is a link failure between R3 and R6* LDP peering must not flap when there is a link failure between R5 and R6Which action meets these requirements?

Configure LDP Session Protection on R4

Reset the LDP session between R4 and R6

Configure LDP Session Protection on R4

Implement an LDP targeted session with R4 on R6

Refer to the exhibit. Refer to the exhibit. ISP A provides VPLS services and DDoS protection to Company XYZ to connect their branches across the North America and Europe regions. The uplink from the data center to the ISP is Mbps. The company XYZ security team asked the ISP to redirect ICMP requests which are currently going to the web server to a new local security appliance which configuration must an ISPP engineer apply to router R2 to redirect the ICMP traffic?

class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 1 match ipv4 icmp-type 8

class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 7 match ipv4 icmp-type 3

class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 1 match ipv4 icmp-type 8

class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 3 match ipv4 icmp-type 5

class-map type traffic match-all B_210.10.65.1 match destination-address ipv4 210.10.65.1 match protocol 6 match ipv4 icmp-type 9

Refer to the exhibit. Refer to the exhibit. An engineering team must update the network configuration so that data traffic from router A to router D continues in case of a network outage between routers B and C. During a recent outage on the B-C link, the IGP traffic path was switched to the alternate path via routers E and F. but label forwarding did not occur on the new path. Which action ensures that traffic on the end-to-end path continues?

Enable MPLS LDP IGP Synchronization on all routers

Configure the same hello timer values for IGP and LDP

Bind the BFD protocol with IGP on all routers

Enable LDP Session Protection on routers A and D.

Enable MPLS LDP IGP Synchronization on all routers

Refer to the exhibit. Refer to the exhibit. Router 1 and Router 2 were installed in the data center. Router 1 is the core router in the network, but it fails to establish an OSPF peering with Router 2. and customer traffic is unable to pass. Router 1 also reports an increase in CPU and memory usage. However, the CPU for R2 is stable. Which action resolves this issue?

Change the MTU to 1524 on Router 1.

Disable Cisco Express Forwarding on Router 2.

Change the transport mode to WAN on Router 1.

Change the MTU to 1524 on Router 1.

What is the primary role of a BR router in a 6rd environment?

It connects the CE routers with the IPv6 network.

It provides connectivity between end devices and the IPv4 network.

It embeds the IPv4 address in the 2002::/16 prefix.

It connects the CE routers with the IPv6 network.

It provides IPv4-in-IPv6 encapsulation

Refer to the exhibit. An engineer ran this show telemetry command to view subscription SUB11 on RouterX. The engineer then decided that RouterY should provide the same output lor sensor group SGroup13 as RouterX. The engineer cannot access RouterX to copy its configuration No access lists on the router block user access Which configuration must the engineer apply on RouterY to provide the same output from the show telemetry command?

RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# destination-group SUB11RouterY(config-model-driven-dest)# address family ipv4 172.16.10.1 port 22471RouterY(config-model-driven-dest-addr)# encoding self-describing-gpbRouterY(config-model-driven-dest-addr)# protocol tcp

RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# subscription SGroup13RouterY(config-model-driven-subs)# sensor-group-id SGroup13 sample-interval 20000

RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# sensor-group SGroup13RouterY(config-model-driven-snsr-grp)# sensor-path openconfig-interfaces:interfaces/interface

RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# destination-group SUB11RouterY(config-model-driven-dest)# address family ipv4 172.16.10.1 port 22471RouterY(config-model-driven-dest-addr)# encoding self-describing-gpbRouterY(config-model-driven-dest-addr)# protocol tcp

RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# subscription SUB11RouterY(config-model-driven-subs)# sensor-group-id SGroup13 sample-interval 20000RouterY(config-model-driven-subs)# destination-id DGroup1

What are two features of stateful NAT64?

It provides 1: N translations, so it supports an unlimited number of endpoints

It provides 1:1 translation so it supports a limited number of end points

It requires the ipv6 hosts to use either DHCPv6 based address assignments or manual address assignments

It requires IPv4 translatable IPv6 address assignments

Refer to the exhibit. Refer to the exhibit. A large organization is merging the network assets of a recently acquired competitor with one of its own satellite offices in the same geographic area. The newly acquired network is running different routing protocol than the company's primary network. As part of the merger a network engineer implemented this route map Which task must the engineer perform to complete the Implementation?

Attach the route map to the redistribution command to manipulate the routes as they are shared

Attach the route map to an IS-IS network statement to advertise the routes learned on this interface to IS-IS

Enable metric style wide to allow the use of extended metrics from the protocols

Attach the route map to the redistribution command to manipulate the routes as they are shared

Configure an additional route map sequence to override the implicit deny at the end of the route map

Refer to the exhibit. Refer to the exhibit An engineer at ISP C is configuring a new interconnection with ISPs A and B using the BGP protocol After the initial configuration the engineer noticed high memory usage and an abnormally large LIB table on router R2 Which two actions must the engineer take on R2 to minimize memory usage? (Choose two.)

Confiure the mpls idp neighbor 11.11.11.11 labels accept1 command.

Configure Standard ACL 1 with accepted prefixes.

Configure Extended ACL 101 with accepted prefixes.

Confiure the mpls idp neighbor 11.11.11.11 labels accept1 command.

Configure Standard ACL 1 with accepted prefixes.

Configure the mpls idp neighbor 1.1.1.1 labels accept 101 command.

Configure the mpls idp neighbor 21.21.21.21 labels accept 101 command.

Refer to the exhibit. Refer to the exhibit. The radio network and packet core are using the route RX-RZ-RB to establish communication. The LDP session between 10.10.10.5 and 10.10.10.1 is experiencing link flapping at random intervals for 30-45 seconds each time. A network engineer must protect the LDP session and improve MPLS traffic convergence. Which action meets these requirements?

Add session protection duration 60 for peer_acl_1 under the MPLS LDP instance on RZ.

Enable IGP_LDP sysnc on RZ and RX

Add session protection duration 60 for peer_acl_1 under the MPLS LDP instance on RZ.

Attach peer_acl_1 in for session protection duration 1 on RX.

Configure Peer_acl_2 on RX and allow IP address 10.10.10.6 in LDP

In an EVPN operation, how does the PE determine and advertise Ethernet segment reachability?

The PE discovers the remote PEs in the EVI and builds a flood list linked with the EVI.

The PE discovers and shared routing information for the B-MAC addresses associated with local Ethernet segments.

The PE discovers other PEs in the same Ethernet segment and elects a DF.

The PE discovers remote ESIs and determines their redundancy mode.

Refer to the exhibit. Refer to the exhibit. A network engineer with an employee ID 4379:43:595 is setting up an IS-IS network with these requirements:*Routes with a tag of 80 and IP prefixes other than 192.168.10.20/24 must be redistributed from Level 1 into Level 2.*Route leaking must be configured from Level 2 into the Level 1 domain for routes that are tagged with only 50 or 40.Which configuration must be implemented on RB to meet the requirements?

Change match tag 80 to match tag 50 in route-map redist1-2.

Add match tag 80 in route-map Ieak2-1

DUMPS Add match ip address 152 in route-map redist1-2

Remove match tag 40 from route-map Ieak2-1

Change match tag 80 to match tag 50 in route-map redist1-2.

Refer to the exhibit. Refer to the exhibit Routers R1 and R2 are connected via a seal link and use the IS-IS routing protocol for route exchange After a configuration change on R2. IS-IS connectivity is interrupted A network engineer confirmed that the interfaces are in the UP state and connectivity exists between the two routers. Which two actions must the engineer perform to resolve the problem? (Choose two.)

Change the MTU to 1500 bytes on R2.

Change R2 to an IS-IS Level 1 router.

Disable padding for hello packets under the serial interface on R2 DUMPS

Change the hello interface timer to 10 seconds on R1.

Change the MTU to 1500 bytes on R2.

Enable hello packet padding globally on R1.

Change R2 to an IS-IS Level 1 router.

Refer to the exhibit. Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service-provider core network with these requirements:*RC must establish LDP peering with the loopback IP address as its Router ID*RA must establish LDP peering with RB. RC, and RY.How must the team update the network configuration to successfully enable LDP peering between RA and RC?

Configure the mpls Idp router-Id loopback0 command on RA and RC.

Enable the mpls ip command on RC interface Gi2/0. DUMPS

Configure the mpls Idp router-Id loopback0 command on RA and RC.

Implement LDP session protection on RA.

DUMPS Reset the discover hello hold time and interval to their default values.

Refer to the exhibit. Refer to the exhibit. A network engineer received a complaint about these problems in OSPF stub area 100:*The Ethernet link is down between routers RX and RY because the fiber was cut.*CE site A traffic to the hub site is being dropped.Which action resolves these issues?

Change the OSPF area 100 type to stub on RZ.

Set the OSPF authentication type to MD5 between RX and RY DUMPS

Change the OSPF area 100 type to stub on RZ.

Change the OSPF priority to 100 on the interfaces that connect RX and RY.

DUMPS Set the OSPF MTU to 1500 on the link between RX and RZ.

Refer to the exhibit. Refer to the exhibit. An engineer is scripting ACLs to handle traffic on the given network. The engineer must block users on the network between R1 and R2 from leaving the network through R5. but these users must still be able to access all resources within the administrative domain. How must the engineer implement the ACL configuration?

Configure an ACL that permits traffic to all internal networks and denies traffic to any external address, and apply it to the R2 interface to R1 in the ingress direction.

Configure an ACL that permits traffic to any internal address, and apply it to the R5 interfaces to R3 and R4 in the egress direction

Configure a permit any ACL on the R1 interface to R2 in the egress direction, and a deny any ACL on the interface in the ingress direction

Configure an ACL that permits traffic to all internal networks and denies traffic to any external address, and apply it to the R2 interface to R1 in the ingress direction.

Configure an ACL that denies traffic to any internal address and denies traffic to any external address, and apply it to the R5 interfaces to R3 and R4 in the ingress direction

Refer to the exhibit. Refer to the exhibit. An engineer is implementing the BGP attribute on the customer's network to select the preferred path. Only BGP's well-known discretionary attribute must be used FTP prefixes should not be selected as part of this implementation. Which configuration must the engineer implement to complete the task?

router bgp 100 neighbor 10.0.0.1 remote-as 500 neighbor 10.0.0.1 route-map ciscotest in

router bgp 100 neighbor 10.0.0.1 remote-as 500 neighbor 10.0.0.1 route-map ciscotest

router bgp 100 neighbor 10.0.0.1 remote-as 500 neighbor 10.0.0.1 route-map ciscotest both

router bgp 100 neighbor 10.0.0.1 remote-as 500 neighbor 10.0.0.1 route-map ciscotest out

Which programmable API allows the service provider to plan and optimize the automation of network operations and achieve closed-loop operations?

Evolved Programmable Network Manager

Refer to the exhibit. Refer to the exhibit. A client wants to filter routes to a BGP peer to limit access to restricted areas within the network. The engineer configures the route map ciscotest to filter routes from the BGP neighbor. The engineer also sets a tag that will be used for QoS in the future. Which task must be performed to complete the Implementation?

Attach the new route map to the BGP neighbor statement in the inbound direction.

Create a policy map named ciscotest and apply It to inbound traffic on the link that is directly connected to the BGP neighbor.

Create a route map, configure BGP with an IPv4 address family, and activate the neighbor.

Add a route map statement with sequence 40 that links a BGP community to the routing protocol

Refer to the exhibit. Refer to the exhibit. Tier 1 ISP A is connected to small Tier 3 ISP B. The EBGP routing protocol is used for route exchange. The networking team at ISP A noticed the flapping of BGP sessions with ISP B. The team decides to Improve stability on the network by suppressing the subnet for 30 minutes when a session begins to flap. Which action must the team perform to meet this goal?

Implement BGP route dampening on ISP A router R1 with the bgp dampening 15 700 1500 30 command.

Implement a BGP route-penalty timer on ISP A router R1 with the bgp penalty-timer 30 250 750 15 command.

Implement BGP route dampening on ISP A router R1 with the bgp dampening 15 700 1500 30 command.

Implement BGP route suppression on ISP A router R2 with the bgp suppression 30 600 1200 30 command.

Implement a BGP route withdraw-delay timer on ISP B router R3 with the bgp withdraw-delay 30 15 90 30 command.

What is the purpose of RSVP tear messages?

to reuse router resources for other reservation requests

to notify the tail-end router of resource unavailability on the transit router

to inform the headend router of LSP issues

to reuse router resources for other reservation requests

to confirm successful end-to-end resource allocation

Refer to the exhibit. Refer to the exhibit. The ISP is implementing a new hosting-as-a-service solution for its business customers. Service accessibility must be unique and separate for each customer. The network architect must ensure that multiple paths toward the hosting-as-a-service solution are always available. Basic protection against traffic black-holing on the MPLS network is required in case of link failure. Which two actions must the engineering team perform to meet the requirements? (Choose two.)

Configure the fast-reroute per-prefix command for the IS-IS protocol in the MPLS network and enable the BGP route-reflector feature on R2.

Configure the mpls Idp sync command in the MPLS network with the BGP additional-paths receive and additional-paths send options.

Create the hosting-as-a-service VRF on router R4 and configure It with the route target both 65123:88 command.

Configure the fast-reroute per-prefix command for the IS-IS protocol in the MPLS network and enable the BGP route-reflector feature on R2.

Enable the VRF-Lite feature on router R4 and enable BGP address-family VPNv4.

Configure the mpls Idp sync command in the MPLS network with the BGP additional-paths receive and additional-paths send options.

Configure the fast-hello command under the IS-IS routing protocol with the BGP multipath 2 option enabled.

Refer to the exhibit. Refer to the exhibit. The operations team for a service provider network is implementing a route map policy. OSPF area 0 should originate the default route with a type 2 metric of 2 when the application server on the connected interface (192.168.1.1) is up. Routers RL and RM have set up OSPF peering with other adjacent routers. Which action meets this requirement?

Apply default-information originate route-map ospf-default-route on router RM.

Apply default-information originate route-map ospf-default-route on router RL.

Configure distribute-list route-map ospf-default-route out on router RM.

Configure distribute-list route-map ospf-default-route out on router RL.

Apply default-information originate route-map ospf-default-route on router RM.

Why is the keyword none needed when implementing management plane security using TACACS?

It allows authentication to succeed when the TACACS+ server is unreachable.

It aItovSWMB6ter to query a RADIUS server when the TACACS+ server is unreachable.

It allows the local database to authenticate when the TACACS^ server is unreachable.

It allows authentication to succeed when the TACACS+ server is unreachable.

It prevents all users from accessing router 1 unless the TACACS+ server is reachable,

Refer to the exhibit. Refer to the exhibit. Router R1 is configured with class map CE with match Ip precedence critical to align with customer contract SLAs. The customer is sending all traffic from CE1 toward the FTP server with IP precedence 5 A network engineer must allow 10% of interface capacity on router R3 Which two actions must the engineer take to accomplish the task? (Choose two )

Implement a class map on R3 to match all packets with QoS IP precedence value 101.

Apply a policy map to R3 to reserve 10% of interface bandwidth.

lmptem4Dt4M$ map on R1 to match all packets with QoS IP precedence value 100.

Implement a class map on R3 to match all packets with QoS IP precedence value 101.

Apply a policy map to R1 to reserve the remaining 10% of interface bandwidth.

Apply a policy map to R3 to reserve 10% of interface bandwidth.

Implement a class map on R3 to match all packets with QoS IP precedence.

What is a feature of mVPN?

It provides the ability to support multicast over a Layer 3 VPN.

It requires-uncast to be disabled on the multicast domain

It establishes multiple static MDTs for each multicast domain.

It provides the ability to support multicast over a Layer 3 VPN.

It requires the no ip mroute-cache command to be configured on the loopback interface of each BGP peer

Refer to the exhibit. Refer to the exhibit BGP is running in the core of the service provider to exchange routes for its customers, and OSPF serves as the PE-CE routing protocol. The service provider s existing customer at CE1 is opening a new office in a different geographical location connected via CE2. A network engineer must update the BGP implementation so that PE1 and PE2 will share routes and provide communication between CE1 and CE2 Which action must the engineer take?

Configure PE1 and PE2 to mutually redistribute BGP and OSPF in the VRF for the customer.

Configured CE2 to establish a BGP relationship with PE1 and PE2

Configure CE1 and CE2 with a pseudowire that will run over the service provider core.

Configure PE1 and PE2 to mutually redistribute BGP and OSPF in the VRF for the customer.

Configure PE1 and PE2 to redistribute OSPF from the VRF for the customer into BGPPUM

Cisco 350-501 Practice Test 10 - Free Online Exam Prep & Questions

Refer to the exhibit.

Cisco 350-501 image Question 361 116643 10102024233012000000

The engineering team wants to limit control traffic on router RX with the following IP address assignments:

• Accepted traffic for router: 10.0.0.0/24

• NOC users IP allocation: 192.168.10.0/24

Which additional configuration must be applied to RX to apply the policy for MSDP?

Become a Premium Member for full access

Unlock Premium Member

Cisco 350-501 Practice Test 10

Question

Cisco 350-501 Practice Tests

Practice Tests