Refer to the exhibit A network engineer is in the process of implementing IS-IS Area 1 and Area 2 on this network to segregate traffic between different segments of the network The hosts in the two new areas must maintain the ability to communicate with one another In both directions. Which additional change must be applied?

Reconfigure either R3 or R4 as a Level 1/Level 2 router.

Reconfigure routers R1, R2 R5. and R6 as Level 1/Level 2 routers.

Reconfigure routers R2 and R5 as Level 1/Level 2 routers.

Reconfigure routers R4, R5 and R6 as Level 1 routers

Which action does the ingress VTEP perform on traffic between EVPN VXLAN overlays?

routing and bridging when doing asymmetric IRB

routing and tunneling when doing symmetric IRB

routing when doing asymmetric IRB

routing and bridging when doing asymmetric IRB

bridging when doing symmetric IRB

Refer to the exhibit. An organization s network recently experienced several significant outages due to device failures. The network administrator just moved the network devices to a new central data center, and packets are switched using labels. The administrator Is now implementing NSF on the network to reduce potential risk factors in the event of another outage. Which task must the administrator perform on each router as part of the process?

Implement Graceful Restart to mitigate the delay in MPLS LDP synchronization when the IGP starts up.

Remove route filtering to speed repopulation of the link-state database

Copy the router s existing state information and share the file with its peers to enable BGP soft resets

Implement MPLS to forward packets while the RIB updates after a faliover.

Implement Graceful Restart to mitigate the delay in MPLS LDP synchronization when the IGP starts up.

A network administrator is planning a new network with a segment-routing architecture using a distributed control plane. How is routing information distributed on such a network?

Each segment is signalled by a compatible routing protocol and each segment makes its own steering decisions based on SR policy.

Each segment is signalled by an SR controller, but each segment makes Its own steering decisions based on SR policy.

Each segment is signalled by MPLS, and each segment makes steering decisions based on the routing policy pushed by BGP.

Each segment is signalled by an SR controller that makes the steering decisions for each node.

Each segment is signalled by a compatible routing protocol and each segment makes its own steering decisions based on SR policy.

When Cisco lOS XE REST API uses HTTP request methods what is the purpose of a PUT request?

updates the specified resource with new information

retrieves the specified resource or representation

submits data to be processed to the specified resource

updates the specified resource with new information

Refer to the exhibit. A network engineer must meet these requirements to provide a connects, solution:The customer connected to Area 2 needs to access the application in Area 1 on the 10.10.10.0/24 subnet The Customer must not have access to the 20.10 30.0/24 subnet.The service provider must make sure that the Area 2 routing database limits the number of IP addresses in the routing tableWhich two configurations must be implemented to meet the requirements? (Choose two)

Set a tag value of 200 to match the summary address 10.0.0.0/16 on R3.

Apply the route map for tag 200 and leak Level 2 routes into Level 1 Area 2 on R3

Set a tag value of 200 to match the summary address 10.0.0/16 on R2.

Set a tag value of 200 to match the summary address 10.0.0.0/16 on R3.

Apply the route map for tag 200 and leak Level 2 routes into Level 1 Area 2 on R3

Apply the route map for tag 200 and teak Level 2 routes into Level 1 Area 2 on R4.

Set a tag value of 200 to match the summary address 10.0.0./16 on R1.

A network operator working for a telecommunication company with an employee Id: 4065 96080 it trying to implement BFD configuration on an existing network of Cisco devices Which task must the engineer perform to enable BFD on the interfaces?

Remove the log option from any ACLs on the interfaces.

Disable Cisco Express Forwarding on the interfaces

Remove any static routes that point to the interfaces

Remove the log option from any ACLs on the interfaces.

A network architect décides to expand the scope of the multicast deployment within the company network the network is already using PlM-SM with a static RP that supports a high-bandwidth. videobased training application that s heavily used by the employees, but excessive bandwidth usage is a concern How must the engineer update the network to provide a more efficient multicast implementation'?

implement BSR to support dynamic RP notification.

Configure IGMP to manage the multicast hosts on each LAN

implement BSR to support dynamic RP notification.

Deploy ICMP to Improve multicast reachability across the network using static RP.

Implement STP to improve switching performance for multicast data.

Refer to the exhibit. The USER mat is connecting an application on an Internet connection in AS 100 is facing these issues:The USER lost the connection to the application during a failure Between IG and R2.Router R2 configuration a lost due to a power outage.The application the USER is connecting to a hosted behind CE2.What action resolves the issues on R3 and R4 routers?

Apply low Local Preference on R4 toward R2.

Set R4 as a route reflector for R3 and CE2

Apply high Local Preference on R3 toward R1

Set R3 as a route reflector for R4 and CE1

Apply low Local Preference on R4 toward R2.

After a series of unexpected device failures on the network. a Cisco engineer is deploying NSF on the network devices so that packets continue to be forwarded during switchovers The network devices reside in the same holding, but they are physically separated into two different data centers Which task must the engineer perform as part of the deployment?

implement VRFs ana specify the forwarding instances that must remain active during failover.

implement OSPF to maintain the link-state database during failover.

implement VRFs ana specify the forwarding instances that must remain active during failover.

implement an L2VPN with the failover peer to share state Information between the active and standby devices.

implement Cisco Express Forwarding to provide forwarding during failover

Refer to me exhibit. A network engineer notices PE-21 convergence degradation due to the growing LSDB size of Level 2 areas in the network The engineer decides to migrate router PE-21 from an inter-area design to an intra-area implementation, inter-area routing must De accomplished via an ATT-bit set by the Level 1/Level 2 router. Which configuration must the engineer implement on PE-21 to complete the migrate?

configure terminalrouter isis 1no net 49.0200.0100.1202.0021.00net 49.5000.0100.1202.0021.00is-type level-1end

configure terminalrouter isis 1no net 49.0200net 49.5000is-type level-1-2end

configure terminalrouter isis 1net 49.5000.0100.1202.0021.00is-type level-1-2end

configure terminalrouter isis 1net 49.5000.0100.1222.0022.00is-type level-1end

configure terminalrouter isis 1no net 49.0200.0100.1202.0021.00net 49.5000.0100.1202.0021.00is-type level-1end

An engineer Is implementing NSR with OSPF on a large campus that requires high availability. Which task must an engineer perform to complete the process with minimal disruption to traffic?

Ensure that the dual HP has synchronized their state information before performing the switchover operation.

Reset OSPF neighbour sessions to maintain state Information during router switchover

Configure the device to repopulate state information using routing updates received from the BDR

increase the keepalive interval on the OSPF neighbours so that traffic continues to pass during the switchover.

Ensure that the dual HP has synchronized their state information before performing the switchover operation.

Refer to the exhibit. After a networking team configured this MPLS topology, the supervisor wants to view MPLS labels to verify the path that packets take from router R1 to router R7 The team already Issued an ICMP ping to verify connectivity between the devices. Which task must the team perform to allow the supervisor to view the label switch path?

Implement MPLS OAM to display the labels for each hop along the path

Configure MPLS TE to display the labels in the stack between the head and tail-end routers

Implement MPLS LDP to assign labels to all the routes in the transit path.

Configure MPLS LDP Sync to sync labels from the routing table to the MPLS forwarding table.

Implement MPLS OAM to display the labels for each hop along the path

Refer to the exhibit. An administrator working for large ISP must connect its two POP sites to provide internet connectivity to its customers. Which configuration must the administrator perform to establish an iBGP session between routers PE1 on POP site 1 and PE2 on POP site 2?

PE1#configure terminalPE1(config)#router bgp 65111PE1(config-router)#no neighbor 172.19.10.10 shutdownPE1(config-router)#end

PE2#configure terminalPE2(config)#router bgp 65111PE2(config-router)#no neighbor172.18.10.1 shutdownPE2(config-router)#end

PE1#configure terminalPE1(config)#router bgp 65111PE1(config-router)#no neighbor 172.19.10.10 shutdownPE1(config-router)#end

PE1#configure terminalPE1(config)#router bgp 65111PE1(config-router)#address-family ipv4 unicastPE1(config-router-af)#neighbor 172.19.10.10 activatePE1(config-router-af)#end

PE2#configure terminalPE2(config)#router bgp 65111PE2(config-router)#address-family ipv4 unicastPE2(config-router-af)#neighbor 172.18.10.1 activatePE2(config-router-af)#end

Refer to the exhibit. Refer to the exhibit. An Ethernet access provider is configuring routers PE-1 and PE-2 to provide EAccess EVPL service between UNI and ENNI. ENNI service multiplexing is based on 802.1ad tag 150, and service-multiplexed UNI is based on 802.1q tag 10. Which EFP configurations must the provider implement on PE-1 and PE-2 to establish end-to-end connectivity between CE-1 and CE-2?

On PE-1:interface GigabitEthernet2service instance 100 ethernetencapsulation dot1ad 150 dot1q 10rewrite ingress tag pop 2 symmetricOn PE-2:interface GigabitEthernet2service instance 2 ethernetencapsulation dot1q 10

On PE-1:interface GigabitEthernet2service instance 100 ethernetencapsulation dot1ad 150rewrite ingress tag pop 1 symmetricOn PE-2:interface GigabitEthernet2service instance 2 ethernetencapsulation dot1q 10

On PE-1:interface GigabitEthernet2service instance 100 ethernetencapsulation dot1q 150rewrite ingress tag pop 1 symmetricOn PE-2:interface GigabitEthernet2service instance 2 ethernetencapsulation dot1q 10

On PE-1:interface GigabitEthernet2service instance 100 ethernetencapsulation dot1ad 150 dot1q 10rewrite ingress tag pop 2 symmetricOn PE-2:interface GigabitEthernet2service instance 2 ethernetencapsulation dot1q 10

On PE-1:interface GigabitEthernet2service instance 100 ethernetencapsulation dot1ad 150rewrite ingress tag pop 1 symmetricOn PE-2:interface GigabitEthernet2service instance 2 ethernetencapsulation dot1q 10rewrite ingress tag pop 1 symmetric

What are two features of stateful NAT64? (Choose two.)

It provides 1:N translations, so it supports an unlimited number of endpoints.

It requires IPv4-translatable IPv6 address assignments.

It requires the IPv6 hosts to use either DHCPv6-based address assignments or manual address assignments.

It provides 1:1 translation, so it supports a limited number of endpoints.

Cisco 350-501 Practice Test 7 - Free Online Exam Questions 241-280

An engineer must apply an 802.1ad-compliant configuration to a new switchport with these requirements; The switchport must tag all trame when it enters the port The switchport Is expected to provide the same level of service to traffic from any customer VLAN Which configuration must the engineer use?

Cisco 350-501 image Question 241 116523 10102024233011000000

Become a Premium Member for full access

Unlock Premium Member

Cisco 350-501 Practice Test 7

Question

Cisco 350-501 Practice Tests

Practice Tests