A network engineer is configuring Flexible NetFlow and enters these commands What are two results of implementing this feature instead of traditional NetFlow? (Choose two.)

CPU and memory utilization are reduced.

The number of packets to be analyzed are reduced.

CPU and memory utilization are reduced.

Only the flows of top 100 talkers are exported.

The data export flow is more secure

The number of packets to be analyzed are reduced.

The accuracy of the data to be analyzed is improved.

A company needs to improve the use of the network resources that is used to deploy internet access service to customers on separate backbone and internet access network. Which two major design models should be used to configure MPLS L3VPNs and internet service in the same MPLS backbone?(Choose two.)

Internet access routing as another VPN in the ISP network.

Internet access for global routing via a separate interface in a VRF

Carriage of full internet routes in a VPN, in the case of internet access VPNS

Internet routing through global routing on a PE router.

Internet access routing as another VPN in the ISP network.

Internet access through leaking of internet routed from the global table into the L3VPN VRF

Internet access for global routing via a separate interface in a VRF

An engineer implemented LDP protocol on the ISP network. The engineer must ensure that there are no packet loss issues when IGP and LDP protocols are not synchronized. Which configuring must the engineer implement so that the IGP routing protocol will wait until LDP convergence is completed?

Configure MPLS LDP IGP synchronization on the network.

Disable IP CEF routers running LDP and enable LDP protocol.

Configure MPLS LDP IGP synchronization on the network.

Configure LDP sessions protection on the network.

Disable MPLS LDP IGP synchronization on the network.

What is the function of the FEC field within the OTN signal structure?

It allows receivers to correct errors upon data arrival.

It allows the sending devices to apply QoS within the OTN forwarding structure.

It allows source nodes to discard payload errors before transmitting data on the network.

It allows receivers to correct errors upon data arrival.

It allows deep inspection of data payload fields.

Refer to the exhibit. An engineer is reviewing the BGP configuration. Which routes must be advertised to 10.10.10.1

All routes whether local or from other ASNs are permitted.

Local routes are permitted, and routes from other ASNs are denied.

All routes whether local or from other ASNs are denied.

Local routes are denied, and routes from other ASNs are permitted.

All routes whether local or from other ASNs are permitted.

Refer to the exhibit. AN engineer is configuring segment routing on an ISP to simplify traffic engineering and management across network domains. What should the engineer do to complete the implementation of segment routing?

Area authentication must be enable before segment routing will run.

OSPF must be configured with wide area metrics to support routing.

The segment will run without any further configuration.

Area authentication must be enable before segment routing will run.

Area Authentication must be enable before segment routing will run.

How is a telemetry session established for data analytics?

A router initiates a session using the dial-out to a destination.

A destination initiate a session to a router.

The destination initiate a session using the dial-out more to the router.

A router requests the data using Teinet.

Refer to the exhibit. A network administrator implemented MPLS LDP changes on PE-A LSR device. The engineer must ensure there are no LDP peer are fully operational. Which LDP feature must the engineer apply to the existing configuration to eliminate the problem?

Configure MPLS LDP NSR for all LDP sessions.

Configure MPLS LDP IGP synchronization on the network.

Configure MPLS LDP NSR for all LDP sessions.

Enable LDP session protection under the routing protocol.

Disable IP CEF on routers running LDP and enable LDP.

After implement MPLS protocol for multiple VRFs on a single Cisco device, the engineer notices all VRFs on the router still do to not LDP session protection feature enabled. Which configuration must the engineer apply to enable the LDP session protection feature FOR LDP neighbors within each VRF?

Configure LDP session protection within the individual VRFs.

Configure LDP session protection globally on the device only.

Configure LDP session protection globally on the device and on each neighbor that requires session protection.

Configure LDP session authentication on the device to enable LDP session protection on each VRF automatically.

Configure LDP session protection within the individual VRFs.

Refer to the exhibit. An engineer working for private Service Provider with employee id: 3948:11:613 is configuring the BGPsec framework. Which two conditions must the engineer take into account? (Choose two.)

The BGPsec framework secures the AS path.

In BGPsec. all route advertisements are given an expiry time by the originator of the route.

BGPsec uses IPsec tunnel for security.

The BGPsec framework secures the AS path.

In BGPsec. all route advertisements are given an expiry time by the originator of the route.

Private keys are part of the router key pair used to sign route updates.

In BGPsec. route advertisements are not given an expiration time by the originator of the route.

Which characteristic describes prefix segment identifier?

It contains the interface address of the device per each link.

It contains a router to a neighbor.

Refer to the exhibit. An engineer is trying to implement BGP configuration on a router Which configuration error prevents the ASBR from establishing a BGP neighborship to a directly connected BGP speaker?

The TCP session parameters are not specified.

The routing policy is absent for this Cisco IOS XR eBGP instance.

The IPv4 address family configuration under neighbor configuration-mode must be removed.

The VPNv4 address family interferes with the 8GP IPv4 address family negotiations.

The TCP session parameters are not specified.

Refer to the exhibit. An engineer implemented OSPF neighbor relationship on an IOS device. Which configuration must be applied to get the OR/BOR election removed from interfaces running OSPF?

ip ospf network point-to-point on interfaces running OSPF

ip ospf network broadcast on interfaces running OSPF

ip ospf network point-to-point on interfaces running OSPF

ip ospf network multipoint-point on interfaces running OSPF

ip ospf network non-broadcast on n:erfaces running OSPF

After a possible security breach, the network administrator of an ISP must verify the times that several different users logged into the network. Which command must the administrator enter to display the login time of each user that activated a session?

show netconf-yang sessions detail

show platform software yang-management process

Refer to the exhibit. An engineer is configuring path selection on router R1 for two ASNs as shown. Which additional task must the engineer perform on Router 1 so that all outbound traffic utilizes the link between R1 and R3 to reach ASN 4567?

Configure a high weight on the peer to ASN 4567.

Configure a low weigh! on the peer to ASN 4567.

Configure a high weight on the peer to ASN 4567.

Configure an AS path prepend on the peer to ASN 4567.

Configure a high med on the peer to ASN 4567.

A network operator needs to implement PIM-SSM multicast configuration on customer's network so that users in different domains are able to access and stream live traffic. Which two actions must the engineer perform on the network to make the streaming work? (Choose two.)

Configure at least one MSDP peer on the network

Enable IGMP version 3 at the interface level.

Configure at least one MSDP peer on the network

Enable IGMP version 2 at the interface lever.

Enable PIM sparse mode on the device.

Enable IGMP version 3 at the interface level.

Enable PM dense mode on the device.

Refer to the exhibit. What does this REST API script configure?

interface with IP address 192.168.0.1

public community string for SNMP

interface with IP address 192.168.0.1

What is the role of NSO in network automation?

It is a tool used to bridge automation to the physical network infrastructure.

It is GUI used to manage wireless devices in a campus infrastructure.

It Is a type of REST API used to configure an APIC.

It is a tool that uses CLl only to configure virtual network devices.

It is a tool used to bridge automation to the physical network infrastructure.

Which two tasks must an engineer perform when implementing LDP NSF on the network? (Choose two.)

Enable NSF for the link-state routing protocol that is in use on the network.

Disable Cisco Express Forwarding.

Enable NSF for the link-state routing protocol that is in use on the network.

Implement direct connections for LDP peers.

Refer to the exhibit. A network engineer notices that router R2 is failing to install network 172.16.33.1/32 in the routing table. Which configuration must the engineer apply to R2 to fix the problem?

R2(config)# access-list 1 permit 172.16.33.0 0.0.0.255

R2(config)# access-Iist 1 permit 172.16.33.0 255.0.0.0

R2(config)# access-list 1 permit 172,16,33.0 255,255,255,0

R2(config)# access-list 1 permit 172.16.33.0 0.0.0.255

R2(config)# access-list 1 permit 172,16,33.0 255.255,0,0

A network engineer has configured TE tunnels in the MPLS provider core. Which two steps ensure traffic traverse? (Choose two.)

Forwarding adjacency features allows a tunnel to be Installed in the IGP table as a link.

The IGP metric of a tunnel is configured to prefer a certain path

Static routes is the only option for directing traffic into a tunnel.

ECMP between tunnels allows RSVP to function correctly.

Forwarding adjacency features allows a tunnel to be Installed in the IGP table as a link.

The IGP metric of a tunnel is configured to prefer a certain path

A tunnel weight is configured in SPF database the same way as a native link.

A remote operation center is deploying a set of l-BGP and E-BGP connections for multiple IOS-XR platforms using the same template. The l-BGP sessions exchange prefixes with no apparent issues, but the E-BGP sessions do not exchange routes. What causes this issue?

The E-BGP neighbors are not allowed to exchange information doe to the customer platforms default policy.

A PASS ALL policy has no! been implemented for the l-BGP neighbors.

The next-hop-self command is not implemented on both E-BGP neighbors.

The E-BGP neighbors are not allowed to exchange information doe to the customer platforms default policy.

The l-BGP neighbors are mistyped and HELLO packets cannot be exchanged successfully between routers.

Refer to the exhibit. A network engineer Is implementing OSPF multiare a. Which command on interface G0/1 resolves adjacency Issues in the new area?

Ip ospf network polnt-to-multlpoint

What is a constraint of Cisco MPLS TE tunnel configurations?

Tunnels cannot be configured over IP unnumbered links.

Tunnels cannot span multiple OSPF areas.

With ISIS as an IGP. only older-style metrics are used.

Tunnels cannot be configured over IP unnumbered links.

QoS-aware tunneling is not supported.

Cisco 350-501 Practice Test 5 - Free Online Exam Questions 161-200

A network engineer is configuring Flexible NetFlow and enters these commands

Cisco 350-501 image Question 161 116443 10102024233011000000

What are two results of implementing this feature instead of traditional NetFlow? (Choose two.)

Become a Premium Member for full access

Unlock Premium Member

Cisco 350-501 Practice Test 5

Question

Cisco 350-501 Practice Tests

Practice Tests