Home / HP / HPE0-S60

HP HPE0-S60 Practice Test - Questions Answers, Page 6

Question list

List of questions

Question 51

(0)

Your customer has the following HPE Synergy setup: - 15 HPE Synergy 12000 frames with 50Gb connectivity to each server port - 2 HPE Composer 2 modules - 15 HPE D3940 Storage Modules, one per fram

Question 52

(0)

HOTSPOT An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade. Click the parameter that the customer should configure within an up

Question 53

(0)

HOTSPOT Click the area within the iLO management interface that will allow you to access workload Advisor.

Question 54

(0)

DRAG DROP You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView. Put the steps to achieve this goal into the coned order in the answer area on the right.

Question 55

(0)

HOTSPOT Click the option that will allow you to change the ESXI image used In an OS Deployment Plan.

Question 56

(0)

DRAG DROP Your customer plans to use HPE OneView for VMware vCenter Server to deploy ESXi systems. They created a server profile template that they want to use in HPE OneView. Put the steps requir

Question 57

(0)

HOTSPOT After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log. Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow yo

Question 58

(0)

DRAG DROP Match each HPE Synergy logical component with the definition.

Question 59

(0)

HOTSPOT Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.

Question 60

(0)

HOTSPOT Your customer is implementing an HPE Synergy solution based on three frames. Click each of the ports that can be used to connect satellite modules.

Related questions

Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets Which HPE compute system meets the customer requirements?

Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric. The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They also plan a vSAN deployment leveraging HPE D3940 Storage Modules and SSD drives The customer requested the following components: - HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules - Two HPE Virtual Connect SE 100Gb F32 Modules for Synergy - An appropriate number of vSAN Standard licenses for each compute node - One HPE O3940 Storage Module with 40 SSDs - All required cables and options Which statement about this request is true?

Which statement about a new HPE SimpliVity deployment is true?

Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?

You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system. What is required from the VMware side to enable LAG?

You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter. Which storage object should you check using SSMC to verify whether vVol datastore is configured property?

Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?

Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory. Which HPE compute system meets this customer's requirements?

Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex 280 They plan to manage new components using HPE OneView What must be done to achieve this goal?

Question 51

Your customer has the following HPE Synergy setup:

- 15 HPE Synergy 12000 frames with 50Gb connectivity to each server port

- 2 HPE Composer 2 modules

- 15 HPE D3940 Storage Modules, one per frame

- 2 HPE 12Gb SAS switches per frame

Which statement about this setup is true?

The customer must create at least five logical enclosures for this setup.

To manage 15 frames, additional HPE Composers are required.

The customer can install up to 12 HPE Synergy 480 compute nodes per frame.

If properly cabled, any compute node can access any HPE D3490 storage module

Show Answer Comment (0)

Question 52

HOTSPOT

An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.

Click the parameter that the customer should configure within an uplink set to meet this requirement

Show Answer Comment (0)

Question 53

HOTSPOT

Click the area within the iLO management interface that will allow you to access workload Advisor.

Show Answer Comment (0)

Question 54

DRAG DROP

You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.

Put the steps to achieve this goal into the coned order in the answer area on the right.

Show Answer Comment (0)

Question 55

HOTSPOT

Click the option that will allow you to change the ESXI image used In an OS Deployment Plan.

Show Answer Comment (0)

Question 56

DRAG DROP

Your customer plans to use HPE OneView for VMware vCenter Server to deploy ESXi systems. They created a server profile template that they want to use in HPE OneView.

Put the steps required to configure HPE OneView for VMware vCenter Server on the left into their correct order on the right.

Show Answer Comment (0)

Question 57

HOTSPOT

After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.

Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.

Show Answer Comment (0)

Question 58

DRAG DROP

Match each HPE Synergy logical component with the definition.

Show Answer Comment (0)

Question 59

HOTSPOT

Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.

Show Answer Comment (0)

Question 60

HOTSPOT

Your customer is implementing an HPE Synergy solution based on three frames.

Click each of the ports that can be used to connect satellite modules.

Show Answer Comment (0)

Total 78 questions

4 5 6 7 8

Go to page: of 8