ExamGecko
Login
Home / HP / HPE6-A73 / List of questions
Ask Question

HP HPE6-A73 Practice Test - Questions Answers, Page 13

Add to Whishlist

List of questions

Question 121

Report Export Collapse

Examine the network exhibit:

HP HPE6-A73 image Question 121 14690 09162024180712000000

Examine Rome r4's partial OSPF configuration: router OSPF 1

Area 0

exit interface vlan 100

ip ospf area 0

exit interface vlan 40

ip ospf area 0

exit interface 1/1/1

vlan access 100

mtu9000

Ip ospt hello-Interval 1

Ip ospt dead-Interval 4

ip ospf authentication simple-text

ip ospf authentication-key key123

When executing the 'show ip ospf neighbors' command, Router 4 is in a FULL state with Router 3 and Router 2, but a 2-WAY state with Route3. What is causing the 2-WAY state with Router 1?

Become a Premium Member for full access
  Unlock Premium Member

Question 122

Report Export Collapse

Which does VOQ implement that is different from most typical campus switches?

Become a Premium Member for full access
  Unlock Premium Member

Question 123

Report Export Collapse

An administrator will be deploying HPE Aruba Networking Switch Multi-Edit Software to manage an Aruba solution. What does Switch Multi-Edit Software support?

Become a Premium Member for full access
  Unlock Premium Member

Question 124

Report Export Collapse

How does an administrator install a script and create an agent and actions for the Network Analysis Engine running on AOS-CX switches?

Become a Premium Member for full access
  Unlock Premium Member

Question 125

Report Export Collapse

Examine the configuration of Core-1 and Core-2. AOS-CX switches configured as a VSX stack:

Core1: Interlace lag 256

no shutdown

no routing

vlan trunk allowed all

lacp mode active Interface 1/1/46

no shutdown

lag 256 Interface 1/1/47

no shutdown

lag 256

VSX

Inter-switch-link lag 256

vsx-sync vsx-global

exit

Cofe2: interlace lag 250

no shutdown

no routing

vlan trunk allowed all

lacp mode active

Interlace 1/1/46

no shutdown

lag 256 Interface 1/1/47

no shutdown

lag 256 vsx

inter-switch-link lag 256

exit

When using the 'show vsx status' command, the two switches fall to connect and successfully synchronize. What should the administrator do to fix this issue?

Become a Premium Member for full access
  Unlock Premium Member

Question 126

Report Export Collapse

An access layer AOS-CX has no OoS configuration on it. The switch receives an 802.1Q tagged VoIP frame on a port. The frame has an 802.1p value of 6. The IP header has a DSCP value of EF46 How will the switch forward this frame?

Become a Premium Member for full access
  Unlock Premium Member

Question 127

Report Export Collapse

An administrate is managing a VSX pair of AOS-CX switches. The administrator configures the following on the secondary switch:

secondary (config)# vlan 100

secondary (conflg. vlan-100) # description BBB

Currently VLAN 100 does not exist on the primary switch. The administrator then accesses the primary switch and configures the following:

Primary(config) vlan 100 primary(config-v1an-100) # description AAA

What Is correct regarding the results of this configuration?

Become a Premium Member for full access
  Unlock Premium Member
Total 127 questions
Go to page: of 13
Open VPLUS File
Convert VPLUS to PDF

Related questions

Examine the commands entered on an AOS-CX switch: What is true regarding this configuration for traffic received on interface 100?
A network engineer is examining NAE graphs from the Dashboard but notices that the time shown in the graph does not represent the current time. The engineer verifies that the AOS-CX switch is configured for NTP and is successfully synchronized. What should be done to fix this issue?
Examine the following ACL rule policies: Permit traffic from 10.2.2.1 through 10.2.2.30 to anywhere Permit traffic from 10.2.2.40 through 10.2.2.55 to anywhere Deny all others Based on this policy, place the following ACL rule statements in the correct order to accomplish the above filtering policy.
When an AOS-CX switch uses a temporary copy of the Configuration State database, what kind of analysis does NetEdit perform to ensure that the configuration is correct?
An administrator has an AOS-CX switch configured with: router ospf 1 area 0 area 1 stub no-summary It is the only ABR for area 1. The switch has the appropriate adjacencies to routing switches in areas 0 and 1. The current routes in each area are: Area 0: 5 routes (LSA Type 1 and 2) Area 1: 10 routes (LSA Type 1 and 2) External routes: 2 (LSA Type 5) Based on the above configuration, how many OSPF routes will routing switches see in Area 1?
A company has recently upgraded their campus switching infrastructure with AOS-CX switches. They have implemented 802.1X authentication on access ports where laptop and IOT devices typically connect. An administrator has noticed that for POE devices, the AOS-CX switch ports are delivering the maximum wattage to the port instead of what the device actually needs. Concerned about this waste of electricity, what should the administrator implement to solve this problem?
A network administrator is attempting to troubleshoot a connectivity issue between a group of users and a particular server. The administrator needs to examine the packets over a period of time from their desktop; however, the administrator is not directly connected to the AOS-CX switch involved with the traffic flow. What is correct regarding the ERSPAN session that needs to be established on an AOS-CX switch? (Choose two.)
An access layer AOS-CX has no OoS configuration on it. The switch receives an 802.1Q tagged VoIP frame on a port. The frame has an 802.1p value of 6. The IP header has a DSCP value of EF46 How will the switch forward this frame?
An administrator wants to implement dynamic segmentation policies. The network consists of AOSCX and Aruba gateways. Which type of forwarding should the administrator implement for users that already connect via wireless, but will also be connecting on Ethernet switch ports?
An administrator wants to track what configuration changes were made on a switch. What should the administrator implement to see the configuration changes on an AOS-CX switch?