Home / Juniper / JN0-363

Juniper JN0-363 Practice Test - Questions Answers

Question list

List of questions

Question 1

(0)

You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)

Question 2

(0)

Which configuration selling prohibits a static route from being redistributed by a dynamic routing protocol?

Question 3

(0)

Exhibit Which two statements are correct about the information shown in the exhibit? (Choose two.)

Question 4

(0)

Exhibit You are advertising a summary route that represents your local network (172.20.0.0716) to both ISP A and ISPB. You want to influence all traffic sent to you from ISP C to go through R2.

Question 5

(0)

Which two statements ate correct about the community BGP attribute on a Junos device? (Choose two.)

Question 6

(0)

Exhibit Referring to the exhibit, how do you verify the status of the tunnel from R1?

Question 7

(0)

You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

Question 8

(0)

The segment touting SRGB start label Is 10,000 and the SRGB index range is 500. In this scenario, which two statements are correct? (Choose two.)

Question 9

(0)

Exhibit You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit. What is the problem in this

Question 10

(0)

Exhibit The routers shown in the exhibit ate configured for segment routing. In this scenario, what is the adjacency SIO that Router B advertises to Router A?

Question 1

You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)

Use physical interfaces.

Use an IRB interface.

Use logical tunnel interfaces.

Use loopback interfaces.

Show Answer Comment (0)

Question 2

Which configuration selling prohibits a static route from being redistributed by a dynamic routing protocol?

route-filter

no-readvertise

qualified-next-hop

passive

Show Answer Comment (0)

Question 3

Exhibit

Which two statements are correct about the information shown in the exhibit? (Choose two.)

The root bridge is reachable using the ge-0/0/14 interface.

This switch is the root bridge for this spanning tree topology.

This switch has a bridge priority of 8k.

The root bridge's priority Is 4k.

Show Answer Comment (0)

Question 4

Exhibit

You are advertising a summary route that represents your local network (172.20.0.0716) to both ISP A and ISPB. You want to influence all traffic sent to you from ISP C to go through R2.

How would you accomplish this task?

On R1, prepend your AS number three times on the 172.20.0.0/16 route when advertising It to ISP 1.

On R1, change the local preference value to 250.

On R2. prepend your AS number three times on the 172.20.0.0/16 route when advertising it to ISP 2.

On R2, change the local preference value to 50.

Show Answer Comment (0)

Question 5

Which two statements ate correct about the community BGP attribute on a Junos device? (Choose two.)

The community attribute is a mandatory BGP attribute.

If the community attribute is present, it is ignored and deleted in the BGP updates.

If the community attribute is present, it should be passed unchanged in the BGP updates.

The community attribute is an optional BGP attribute.

Show Answer Comment (0)

Question 6

Exhibit

Referring to the exhibit, how do you verify the status of the tunnel from R1?

Issue the ping 172.20.111.10 source 172.20.110.1 command.

Issue the ping 172.20.111.10 source 198.51.100.1 command.

Issue the ping 172.20.iii.io source 203.0.113.2 command.

Issue the ping 172.20. Ill. 10 command.

Show Answer Comment (0)

Question 7

You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

You must use the no-cspf parameter in the label-switched-path configuration.

Traffic engineering extensions ate enabled by default In OSPF.

Traffic engineering extensions are not enabled by default in OSPF.

You must use the policing parameter in the label-switched-path configuration.

Show Answer Comment (0)

Question 8

The segment touting SRGB start label Is 10,000 and the SRGB index range is 500.

In this scenario, which two statements are correct? (Choose two.)

The first usable label is 10,001.

The last usable label is 10.501.

The last usable label is 10,499.

The first usable label Is 10,000.

Show Answer Comment (0)

Question 9

Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.

What is the problem in this scenario?

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

Show Answer Comment (0)