ExamGecko
Login
Home / Juniper / JN0-363 / List of questions
Ask Question

Juniper JN0-363 Practice Test - Questions Answers, Page 4

Add to Whishlist

List of questions

Question 31

Report Export Collapse

Exhibit

Juniper JN0-363 image Question 31 50692 09182024211219000000

You are asked to assign interface xe-1/0/5 to a virtual switch.

What must be accomplished to complete the configuration?

Interface xe-1/0/5 must be added to routing-instance sw-1 vlan_2.
Interface xe-1/0/5 must be added to routing-instance sw-1 vlan_2.
Interface xe-1/0'5 must be a trunk port.
Interface xe-1/0'5 must be a trunk port.
Interface xe-1/0/5 must be added to routing-instance sw-1.
Interface xe-1/0/5 must be added to routing-instance sw-1.
An IRB interface must be configured to routing-instance sw-1 vlan_2.
An IRB interface must be configured to routing-instance sw-1 vlan_2.
Suggested answer: C
asked 18/09/2024
Kurt Van Rymenant
52 questions

Question 32

Report Export Collapse

Exhibit

Juniper JN0-363 image Question 32 50693 09182024211219000000

Referring to the exhibit, which statement is true about VRRP?

VRRP communication between the two devices is not functioning correctly.
VRRP communication between the two devices is not functioning correctly.
Both routers are in the same state because they have the same VRRP priority.
Both routers are in the same state because they have the same VRRP priority.
RRP Is functioning normally in active/active mode.
RRP Is functioning normally in active/active mode.
The routers should use different virtual IP addresses for VRRP to function correctly.
The routers should use different virtual IP addresses for VRRP to function correctly.
Suggested answer: D
asked 18/09/2024
Sivakumar Duraimanickam
41 questions

Question 33

Report Export Collapse

Exhibit.

Juniper JN0-363 image Question 33 50694 09182024211219000000

Referring to the exhibit, you have configured an aggregate route that represents the 172.21.0.0/24, 172.21.1.0/24, and 172.21.2.0/24 networks. However, when you view the routing table, your new route hidden.

Which action would you perform to determine the problem?

Verify that you have active contributing routes on the device.
Verify that you have active contributing routes on the device.
Verify that you have configured a policy on the device to accept aggregate routes.
Verify that you have configured a policy on the device to accept aggregate routes.
Verify that you have defined a metric value for the aggregate route.
Verify that you have defined a metric value for the aggregate route.
Verify that you have set the preference to a lower default value.
Verify that you have set the preference to a lower default value.
Suggested answer: D
asked 18/09/2024
Thutcha sudjitjjoon
42 questions

Question 34

Report Export Collapse

What are two bridging concepts that are used to maintain an Ethernet switching table? (Choose two.)

learning
learning
exporting
exporting
aging
aging
timing
timing
Suggested answer: A
asked 18/09/2024
Niall Dempsey
40 questions

Question 35

Report Export Collapse

Exhibit

Juniper JN0-363 image Question 35 50696 09182024211219000000

You are asked to configure the OSPF environment to prevent the DRother routers from participating in DR/BDR election.

Referring to the exhibit, which command will accomplish this task?

set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 255
set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 255
set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority 0
set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority 0
set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma
set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma
set protocols ospf area 0.0.0.0 interface ge---0/0/1 interface-type p2p
set protocols ospf area 0.0.0.0 interface ge---0/0/1 interface-type p2p
Suggested answer: A
asked 18/09/2024
Francisco Jesús Cano Hinarejos
59 questions

Question 36

Report Export Collapse

Exhibit

Juniper JN0-363 image Question 36 50697 09182024211219000000

Which two statements ate correct about the actions taken as the packet traverses the service provider MPLS network from Site 1 to Site 2 as shown in the exhibit? (Choose two.)

R2 will perform a lookup using the mpls.0 table.
R2 will perform a lookup using the mpls.0 table.
R1 will perform a lookup using the lnet.3 table.
R1 will perform a lookup using the lnet.3 table.
R1 will perform a lookup using the mpls.0 table.
R1 will perform a lookup using the mpls.0 table.
R2 will perform a lookup using the inet.3 table.
R2 will perform a lookup using the inet.3 table.
Suggested answer: A
asked 18/09/2024
Ed Robbins
36 questions

Question 37

Report Export Collapse

Exhibit

S Exhibit

LSI1 A AS 65501

ISPB AS 65502

Advertised Prefixes: 172.20.0.0/24 172.20.20.0/24 172.20.21.0/24

\ N

Advertised Prefixes: 172.20.0.0/24

172.20.1.0/24

Juniper JN0-363 image Question 37 50698 09182024211219000000

Referring to the exhibit, which two statements are correct? (Choose two.)

Devices in AS 65512 will prefer ISP A for traffic destined to the 172.20.21.0/24 network.
Devices in AS 65512 will prefer ISP A for traffic destined to the 172.20.21.0/24 network.
Devices In AS 65512 will prefer ISP A for traffic destined to the 172.20.0.0/24 network.
Devices In AS 65512 will prefer ISP A for traffic destined to the 172.20.0.0/24 network.
Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.21.0/24 network.
Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.21.0/24 network.
Devices In AS 65512 will prefer ISP B for traffic destined to the 172.20.0.0/24 network.
Devices In AS 65512 will prefer ISP B for traffic destined to the 172.20.0.0/24 network.
Suggested answer: C
asked 18/09/2024
Ayo dickson
54 questions

Question 38

Report Export Collapse

Exhibit

Juniper JN0-363 image Question 38 50699 09182024211219000000

You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.

Which action will accomplish this behavior?

Configure the ultimace-hop-popping statement under the R1_TO_R5 label switched path on R1.
Configure the ultimace-hop-popping statement under the R1_TO_R5 label switched path on R1.
Configure the explicit-null statement under the protocol mpls hierarchy on R1.
Configure the explicit-null statement under the protocol mpls hierarchy on R1.
Delete the no-espf statement under the R1_TO_R5 label switched path on R1.
Delete the no-espf statement under the R1_TO_R5 label switched path on R1.
Configure the install statement under the R1_TO_R5 label switched path on R1.
Configure the install statement under the R1_TO_R5 label switched path on R1.
Suggested answer: D
Explanation:

https://www.juniper.net/documentation/us/en/software/junos/mpls/topics/ref/statement/install-edit-protocols-mpls.html

asked 18/09/2024
Veridjan Hoxha
44 questions

Question 39

Report Export Collapse

What are three types of MPLS routers? (Choose three.)

transit routers
transit routers
peering routers
peering routers
egress routers
egress routers
aggregation routers
aggregation routers
ingress routers
ingress routers
Suggested answer: A, C, E
Explanation:

https://www.juniper.net/documentation/us/en/software/junos/mpls/topics/topic-map/lsp-routers.html

asked 18/09/2024
Timo Fahlenbck
39 questions

Question 40

Report Export Collapse

Exhibit

Juniper JN0-363 image Question 40 50701 09182024211219000000

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.

Which two tasks will accomplish your objective? (Choose two.)

Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.
Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.
Under the [edit routing-options] hierarchy, configure a 32-bit router ID.
Under the [edit routing-options] hierarchy, configure a 32-bit router ID.
issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.
issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.
Under the [edit routing-options] hierarchy, configure a 128-bit router ID.
Under the [edit routing-options] hierarchy, configure a 128-bit router ID.
Suggested answer: B, C
asked 18/09/2024
Kevin Intriago
39 questions
Total 82 questions
Go to page: of 9
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which two LSA types are permuted in OSPF totally stubby areas? (Choose two.)
You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)
Exhibit Referring to the exhibit, which two additional steps should you lake to fully configure NSR? (Choose two.)
The segment touting SRGB start label Is 10,000 and the SRGB index range is 500. In this scenario, which two statements are correct? (Choose two.)
Which two statements are correct about the way that BGP propagates routes by default? (Choose two.)
Exhibit You are asked to assign interface xe-1/0/5 to a virtual switch. What must be accomplished to complete the configuration?
Which two statements are correct when using LDP? (Choose two.)
Which BGP attribute Is used to detect touting loops?
Exhibit You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command. Referring to the exhibit, what is the problem?
Exhibit Referring to the exhibit, how do you verify the status of the tunnel from R1?