Refer to the exhibit. Refer to the exhibit. A network engineer receives a report that Spoke 1 users can perform bank transactions with the server located at the Center site, but Spoke 2 users cannot. Which action resolves the issue?

Configure IPv6 on the routers B and C interfaces

Configure the Spoke 2 users IP on the router B OSPF domain

Configure encapsulation dot1q 78 on the router C interface.

Configure IPv6 on the routers B and C interfaces

Configure OSPFv2 on the routers B and C interfaces

A network administrator cannot connect to a device via SSH. The line vty configuration is as follows: Which action resolves this issue?

Configure the transport input SSH

Refer to the exhibits.London must reach Rome using a faster path via EIGRP if all the links are up but it failed to take this path Which action resolves the issue?

Use the network statement on Rome to inject the 172 16 X 0/24 networks into EIGRP

Increase the bandwidth of the link between London and Barcelona

Use the network statement on London to inject the 172 16 X 0/24 networks into EIGRP.

Change the administrative distance of RIP to 150

Use the network statement on Rome to inject the 172 16 X 0/24 networks into EIGRP

What is a function of BFD?

failure detection dependent on routing protocols and media types

peer recovery after a Layer 3 protocol adjacency failure

peer recovery after a Layer 2 adjacency failure

failure detection independent of routing protocols and media types

failure detection dependent on routing protocols and media types

Refer to the exhibit. Refer to the exhibit. AS 111 mut not be used as a transit AS, but ISP-1 is getting ISP-2 routes from AS 111. Which configuration stops Customer AS from being used as a transit path on ISP-1?

ip as-path access-list 1 permit ^$

ip as-path access-list 1 permit_111_

ip as-path access-list 1 permit."

ip as-path access-list 1 permit ^111$

Refer to the exhibit. Refer to the exhibit. An engineer configured user login based on authentication database on the router, but no one can log into the router. Which configuration resolves the issue?

aaa authentication login default local

aaa authentication login default enable

aaa authorization network default local

aaa authentication login default local

aaa authorization exec default local

An engineer received a ticket about a router that has reloaded. The monitoring system graphs show different traffic patterns between logical and physical interfaces when the router is rebooted. Which action resolves the issue?

Configure the snmp ifindex persist command globally.

Clear the logical interfaces with snmp ifindex clear command

Configure the snmp ifindex persist command on the physical interfaces.

Trigger a new snmpwalk from the monitoring system to synchronize interface OlDs

Refer to the exhibit. Refer to the exhibit. Which action limits the access to R2 from 192.168.12.1?

Swap sequence 20 with sequence 10 in access-list 100

Swap sequence 10 with sequence 20 in access-list 100.

Modify sequence 20 to permit tcp host 192.168.12.1 eq 22 any to access-list 100

Swap sequence 20 with sequence 10 in access-list 100

Modify sequence 10 to deny tcp any eq 22 any to access-list 100.

Refer to the exhibit. Refer to the exhibit. After recovering from a power failure. Ethernet0/1 stayed down while Ethernet0/0 returned to the up/up state The default route through ISP1 was not reinstated m the routing table until Ethernet0/1 also came up Which action resolves the issue?

Reference the track object 1 in both static default routes

Remove the references to the interface names from both static default routes

Configure the default route through ISP1 with a higher administrative distance than 2.

Add a static route to the 8 8.8 8/32 destination through the next hop 203.0.113.1

Refer to the exhibit. Refer to me exhibit. The hub and spoke are connected via two DMVPN tunnel interfaces The NHRP is configured and the tunnels are detected on the hub and the spoke Which configuration command adds an IPsec profile on both tunnel interfaces to encrypt traffic?

tunnel protection ipsec profile DMVPN shared

tunnel protection ipsec profile DMVPN multipoint

tunnel protection ipsec profile DMVPN tunnel1

tunnel protection ipsec profile DMVPN shared

tunnel protection ipsec profile DMVPN unique

Refer to the exhibit. Refer to the exhibit. The administrator is troubleshooting a BGP peering between PE1 and PE3 that is unable to establish Which action resolves the issue?

Ensure that the PE3 loopback address is used as a source for BGP peering to PE1

P2 must have a route to PE3 to establish a BGP session to PE1

Disable sending ICMP unreachables on P2 to allow PE1 to establish a session with PE3

Ensure that the PE3 loopback address is used as a source for BGP peering to PE1

Remove the traffic filtering rules on P2 blocking the BGP communication between PE1 and PE3

Refer to the exhibit. Refer to the exhibit. An engineer configured SNMP CommÓmes on UserSW2 switch, but the SNMP server cannot upload modified configurations to the switch. Which configuration resolves this issue?

snmp-server community Ciscowruser RW 11

snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22

snmp-server community CiscOUs3r RW 11

snmp-server group NETVIEW v2c priv read NETVIEW access 11

Refer to the exhibit. Refer to the exhibit. An engineer configured SNMP traps to record spoofed packets drop of more than 48000 a minute on the ethernet0/0 interlace. During an IP spoofing attack, the engineer noticed that no notifications have been received by the SNMP server. Which configuration resolves the issue on R1?

ip verify unicast notification threshold 800

ip verity unicast notification threshold 48000

ip verify unicast notification threshold 8000

ip verify unicast notification threshold 800

ip verify unicast notification threshold 80

What are two characteristics of a VRF instance? (Choose two)

Each VRF has a different set of routing and CEF tables.

An interface must be associated to one VRF

It is defined by the VPN membership of a customer site attached to a P device.

Each VRF has a different set of routing and CEF tables.

AII VRFS share customers routing and CEF tables.

An interface must be associated to one VRF

A customer site can be associated to different VRFs.

The network administrator configured CoPP so that all routing protocol traffic toward the router CPU is limited to 1 mbps. All traffic that exceeds this limit must be dropped. The router is running BGP and OSPF Management traffic for Telnet and SSH must be limited to 500kbps.access-list 100 permit tcp any any eq 179access-list 100 permit tcp any any range 22 23access-list 100 permit ospf any any!class-map CM-ROUTINGmatch access-group 100class-map CM-MGMTmatch access-group 100!policy-map PM-COPPclass CM-ROUTINGpolice 1000000 conform-action transmitclass CM-MGMTpolice 500000 conform-action transmit!control-planeservice-policy output PM-COPPNo traffic is filtering through CoPP, which is resulting in high CPU utilization,which configuration resolves the issue ?

no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101!control-planeno service-policy output PM-COPPservice-policy input PM-COPP

no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101

control-planeno service-policy output PM-COPPservice-policy input PM-COPP

No access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit tcp any any range eq 22access-list 100 permit tcp any any range eq 23access-list 100 permit ospf any any

no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101!control-planeno service-policy output PM-COPPservice-policy input PM-COPP

An engineer is creating a policy that overrides normal routing behavior.if the route to a destination of 10.100.100.0/24 is withdrawn from the routing Table, the policy must direct traffic to a next hop of 10.1 1.1. if the route is present in the routing table, then normal forwarding must occur. Which configuration meets the requirements?

access-list 100 permit ip any 10.100.100.0 0.0.0.255!route map POLICY permit 10match ip address 100Set ip next-hop recursive 10.1.1.1!route-map POLICY permit 20

access-list 100 permit ip any any!route-map POLICY permit 10match ip address 100set ip next-hop recursive 10.1.1.1

access-list 100 permit ip any 10.100.100.0 0.0.0.255!Route-map POLICY permit 10match ip address 100set ip default next-hop 10.1.1.1

ICY permit 10match ip address 100set ip next-hop 10.1.1.1!route map POLICY permit 20

access-list 100 permit ip any 10.100.100.0 0.0.0.255!route map POLICY permit 10match ip address 100Set ip next-hop recursive 10.1.1.1!route-map POLICY permit 20

Refer to the exhibit. After a new regional office is set up,not all guests can access the internet via guest WiFi. Clients are getting the correct IP address from guest Wi-Fi VLAN 364. which action resolves the issue ?

Allow DNS traffic through the inbound ACL

Allow 10.66.46.0/23 in the outbound ACL

Allow DNS traffic through the outbound ACL

Allow DNS traffic through the inbound ACL

Allow 10.66.46.0/23 in the inbound ACL

An engineer configures PBR on R5 and wants to create a policy that matches traffic destined toward 10.10.10.0/24 and forward 10.1.1.1. The traffic must also have its IP precedence set to 5.All other traffic should be forward toward 10.1.1.2 and have its IP precedence set to 0.Which configuration meets the requirements?

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address100 set ip next-hop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ip precedence 0

access-list 1 permit 10.10.10.0 0.0.0.255access-list 2 permit anyroute-map CCNP permit 10match ip address 1set ip next-hop 10.1.1.1set ip precedence 5!route-map CCNP permit 20match ip address 2set ip next-hop 10.1.1.2set ip precedence 0route-map CCNP permit 30

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address 100 set ip next-hop 10.1.1.1 set ip precedence 0 ! route-map CCNP permit 20set ip next-hop 10.1.1.2set ip precedence 5!route-map CCNP permit 30

access-list 1 permit 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address 1 set ipnexthop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ipprecedence 0

access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10 match ip address100 set ip next-hop 10.1.1.1 set ip precedence 5 ! route-map CCNP permit 20 set ip next-hop 10.1.1.2 set ip precedence 0

Refer to the exhibit. A network administrator is trying to switch to the privileged EXEC level on R1 but failed. Which configuration resolves the issue?

tacass server enable-password Cisco@123

tacacs-server enable-password Cisco@123

What is a function of the IPv6 DHCP Guard feature for DHCP messages?

It blocks only DHCP request messages.

Only access lists are supported for matching traffic.

All client messages are always switched regardless of the device role.

It blocks only DHCP request messages.

If the device is configured as a DHCP server, no message is switched.

Refer to the exhibit. R1 has a route map configured, which results in a loss of partial IPv6 prefixes for the BGP neighbor, resulting in service degradation. How can the full service be restored?

The route map requires a permit 20 statement without set conditions, and this will allow additional prefixes to be advertised.

The neighbor requires a soft reconfiguration, and this will clear the policy without resetting the BGP TCP connection.

The prefix lit requires all prefixes that R1 is advertising to be added to it, and this will allow additional prefixes to be advertised.

The route map requires a deny 20 statement without set conditions, and this will allow additional prefixes to be advertised.

The route map requires a permit 20 statement without set conditions, and this will allow additional prefixes to be advertised.

Cisco 300-410 Practice Test 10 - Free Online Exam Prep & Questions

Refer to the exhibit.

Cisco 300-410 image Question 361 111307 10072024005414000000

An administrator configures a router to stop using a particular default route if the DNS server 8.8.8.8 is not reachable through that route. However, this configuration did not work as desired and the default route still works even if the DNS server 8.8.8 8 is unreachable. Which two configuration changes resolve the issue? (Choose two.)

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-410 Practice Test 10

Question

Cisco 300-410 Practice Tests

Practice Tests