Refer to the exhibit. Refer to the exhibit R1 cannot establish a neighbor relationship with R2 Which action resolves the issue'?

Configure the mtu Ignore command on the Interfaces of R1 and R2

Configure the ip ospf network point-to-point command on the interfaces of R1 and R2

Configure the ip ospf network broadcast command on the interfaces of R1 and R2

Configure the neighbor 2.2.2.2 command on R1 under the OSPF process

Refer to the exhibit. Which action adds the 10 1 7.6-32 route to the BGP table?

Add the network 10.1.7.6 mask 255.255.255.255 command

Add a static roue for the 10 1 7 &32 network

Add the network 10.1.7.6 mask 255.255.255.255 backdoor command

Add summaty-address10.1.7.6.255.255.2550

Add the network 10.1.7.6 mask 255.255.255.255 command

Refer to the exhibit. Refer to the exhibit. An administrator wanted to make R1 always elected as DR. R2 as BDR. and R3 as DROTHER but could not achieve the desired results. Which two configurations resolve the issue? (Choose two.)

On the R1 FO/0 interface, configure OSPF priority to 255.

On the R3 FO'O interface, configure OSPF priority to 201.

On the R1 FO/0 interface, configure OSPF priority to 255.

On the R2 FO/0 interface, configure OSPF priority to 201.

On the R1 F0/0 interface, configure OSPF priority to 202.

On the R3 FO'O interface, configure OSPF priority to 201.

On the R2 FO/0 interface, configure OSPF priority to 200.

Refer to the exhibit. Refer to the exhibit. A network engineer configured routers R1 and R2 with MP-BGP. The engineer noticed that the routers cannot exchange any IPv6 routes, however, the IPv4 neighbor relationship is working fine. Which configuration must the engineer apply to router R2 to exchange IPv6 routes?

Ipv6 unicast-routing Ipv6 cef I interface Loopback100 ipv6 address 2001: DB8:128::2/128 ! interface GigabitEthernet1/0 ipv6 address 2001:DB8:1::2/64 i router bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 ! address-family ipv6 network 2001:DB8:128::2/128 neighbor 2001:DB8:1::1 activate

Ipv6cef I Interface Loopback100 Ipv6 address 2001: DB8:128::2/128 Interface GigabitEthernet1/0 Ipv6 address 2001:DB8:1::2/64 I router bgp 65002 no bgp default ipv4-unlcast neighbor 2001: DB8:1::1 emote-as 65001 I address-family ipv6 network 2001:DB8:128::2/128 neighbor 2001:DB8:1::1 activate

Ipv6 unicast-routing ipv6 cef Interface Loopback100 ipv6 address 2001: DB8:12C:2 129 I interface GigabitEthernet1/0 ipv6 address 2001: DB8:1::2 64 description AS65001 ID B466:A83D:3D7::1 ! router bgp 65002 no bgp default Ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 ! address-family Ipv4 neighbor 2001:DB8:1::1 activate

Ipv6 unicast-routing ipvG cef I Interface Loopback100 Ipv6 address 2001:DB8:128::2/128 I interface GigabitEthernet1/0 ipv6 address 2001:DB8:1::2/64 ! router bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 ! address-family ipv6 network 2001:DB8:128::2I128

Ipv6 unicast-routing Ipv6 cef I interface Loopback100 ipv6 address 2001: DB8:128::2/128 ! interface GigabitEthernet1/0 ipv6 address 2001:DB8:1::2/64 i router bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 ! address-family ipv6 network 2001:DB8:128::2/128 neighbor 2001:DB8:1::1 activate

What is the role of LDP in MPLS networks?

It enables label binding information to exchange with peer LSRs

It enables label binding that exchanges route descriptors

It creates MPLS packet forwarding along with the IGP routes.

It disables label binding information to exchange with peer LSRs.

It enables label binding information to exchange with peer LSRs

Refer to the exhibit. An engineer recently implemented uRPF by configuring the ip verify unicast source reachable-via rx command on interface gi0/3 The engineer noticed right after implementing F that an inbound packet on the giO-3 interface with a source address of 172 16 3 251 was dropped. Which action resolves the issue?

Configure uRPF loose mode to forward the packet.

Permit the 172.16.3.251 in the inbound ACL on interface gi0/3.

Permit the 172.16.3.251 in the inbound ACL on interface gi0/3 to allow 172.16.3.251.

Configure uRPF strict mode to forward the packet

Refer to the exhibit. Refer to the exhibit The R2 OSPF route 10 2 2 0/24 shows in the R1 EIGRP routing table without route redistribution performed between OSPF and EIGRP routing protocols Which configuration is required on router R2 to resolve the issue?

Replace the network 10.0.0.0 command with FastEthernet0/0 network in EIGRP 100.

passive-interface FastEthernet 0/0 command in OSPF1.

Add the no auto-summary command in EIGRP 100.

Replace the network 10.0.0.0 command with FastEthernet0/0 network in EIGRP 100.

Add the passive-interface FastEthernet 1/0 command in EIGRP 100

Refer to the exhibit. Refer to the exhibit Which action fixes the OSPF routes redistribution into EIGRP?

Set tags before matching into EIGRP

Set a default metric in the route map

Refer to the exhibit. Refer to the exhibit An engineer investigates an IPv6 EIGRP neighbor adjacency issue that sees the neighbors flapping and issued a ping from R1 to its directly connected neighbor. The link between the switches is stable at Layer 2. and other connected devices are also functioning. Which action resolves the issue?

Multicast packets are not reliably transmitted over the link, and the switch must be replaced.

The switch between the two neighbors is not IPv6 compatible and must be replaced with an IPv6 compatible device.

Data is not reliably transmitted between the dynamically assigned link-local addresses of the routers and must be manually assigned.

Multicast packets are not reliably transmitted over the link, and the switch must be replaced.

The switch between the two neighbors is not configured for IPv6 multicast and must be configured for IPv6 multicast.

Refer to the exhibit. Refer to the exhibit. The primary link between R1 and R2 went down but R3 is still advertising the 192.166.200.0/24 network to R1 and the 192.166.100.0/24 network to R2, which creates a loop. Which action resolves the issue?

Configure the eigrp stub command under the ElGRP process on R3

Configure the summary address 192.168.0.0 255.255.0.0 100 command on R3

Configure the eigrp stub leak-map command under the EIGRP process on R1

Configure the eigrp stub command under the ElGRP process on R2

Refer to the exhibit. Refer to the exhibit. Router ABR-Rtr is not propagating the internet routes in OSPF area 10. which causes internet reachability problems in the are a. Which action resolves the issue?

ABR-Rtr must advertise the 0.0.0.0/0 default route in area 10.

ABR-Rtr must configure the default-information originate always command.

ABR-Rtr must configure the area 10 stub no-summary command.

ABR-Rtr network type must be broadcast network.

ABR-Rtr must advertise the 0.0.0.0/0 default route in area 10.

Refer to the exhibit. Refer to the exhibit. R1 is directly connected to R2 over network 10.100.14.0/24. An engineer configures R1 to advertise a static route that is connected to a local loopback for network 10.100.13.0/24. The network is not in the routing table of R2. Which action resolves the issue?

The redistribution command is incorrect on R1 The keyword subnets should be included with the redistribution command

The redistribution command is incorrect on R1 The default metric metric 200 should be inducted with the redistribution command.

The Loopback interface on R1 is administratively down The interface should be enabled with the no shutdown command

R2 must use a different OSPF process number and should be changed lo ospf 1 to match R1

The redistribution command is incorrect on R1 The keyword subnets should be included with the redistribution command

While BGP internet routes are redistributed to a lower class of router via RIP. packets are being dropped and routes are failing to be distributed in RIP. Which action resolves the issue?

Use the input-queue command to prevent the loss of packets.

Use OSPF instead of RIP to accept all BGP routes.

Use the input-queue command to prevent the loss of packets.

Use WFQ in the output queue of the high-performance router.

Use RIP V2 to be able to use classless networks from BGP

A switch has been configured to provide DHCP relay on VLAN 100 to a server with an IP address of 10.1.1.1. The DHCP server is sending syslog reports of multiple TFTP requests that also originate from the switch. As a result, the server CPU exceeded a configured threshold. Which action does the network administrator recommend to bring the server CPU threshold down?

Configure the switch with no ip forward-protocol udp 69 on VLAN100.

Configure the switch with an access list on VLAN100 to deny TFTP.

Configure the switch with a VACL on VLAN100 to deny TFTP.

Configure the switch with ip forward-protocol udp 67 globally.

Configure the switch with no ip forward-protocol udp 69 on VLAN100.

Refer to the exhibit.SIMULATION

See the answer solution in Explanation

SIMULATIONA network is configured with IP connectivity, and the routing protocol between devices started having problems right after the maintenance window to implement network changes. Troubleshoot and resolve to a fully functional network to ensure that: R4 R5

See the answer solution in Explanation

SIMULATIONA DMVPN network is preconfigured with tunnel 0 IP address 192.168.1.254 on the HUB, IP connectivity, crypto policies, profiles, and EIGRP AS 100. The NHRP password is ccnp123, and the network ID and tunnel key is EIGRP ASN Do not introduce a static route. Configure DMVPN connectivity between routers BR1 and BR2 to the HUB router using physical interface as the tunnel source to achieve these goals:

See the answer solution in Explanation

Refer to the exhibit. Refer to the exhibit. Branch 2 hosts cannot receive dynamic IP addresses. Which action resolves the issue?

Configure the ip helper command on the interface GigabitEthernet 0/2 of the R2 router

Configure the Ip helper command on the Layer 2 switch SW2 interfaces

Configure the Ip helper command on the interface GigabitEthernet 0/2 of the DHCP router.

Configure the Ip helper command on the interface GigabitEthernet 0/0 of the DHCP router.

Cisco 300-410 Practice Test 15 - Free Online Exam Questions 561-592

Which Layer 3 VPN attribute allows different customers to connect to the same MPLS network wrth overlapping IP ranges?

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-410 Practice Test 15

Question

Cisco 300-410 Practice Tests

Practice Tests