An engineer is trying to copy an IOS file from one router to another router by using TFTP. Which two actions are needed to allow the file to copy? (Choose two.)

Copy the file to the destination router with the copy tftp: flash: command

Enable the TFTP server on the source router with the tftp-server flash: <filename> command

Copy the file to the destination router with the copy tftp: flash: command

Enable the TFTP server on the source router with the tftp-server flash: <filename> command

TFTP is not supported in recent IOS versions, so an alternative method must be used

Configure a user on the source router with the username tftp password tftp command

Configure the TFTP authentication on the source router with the tftp-server authentication local command

Refer to the exhibit. Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day. Which action fixes the issue within the current resources?

Configure the DHCP lease time to a smaller value

Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool

Configure the DHCP lease time to a smaller value

Configure the DHCP lease time to a bigger value

Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool

Refer to the exhibit. An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?

The keyword localtime is not defined on the timestamp service command.

An authentication error with the NTP server results in an incorrect timestamp.

The keyword localtime is not defined on the timestamp service command.

The NTP server is in a different time zone.

The system clock is set incorrectly to summer-time hours.

A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?

service timestamps log datetime localtime show-timezone

clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00

service timestamps log datetime localtime show-timezone

When provisioning a device in Cisco DNA Center, the engineer sees the error message "Cannot select the device. Not compatible with template".What is the reason for the error?

The tag that was used to filter the templates does not match the device tag.

The template has an incorrect configuration.

The software version of the template is different from the software version of the device.

The changes to the template were not committed.

The tag that was used to filter the templates does not match the device tag.

While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?

The software image for the device is in install mode.

The device must be resynced to Cisco DNA Center.

The software image for the device is in install mode.

The device has lost connectivity to Cisco DNA Center.

The software image for the device is in bundle mode

An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?

sudo maglev install config update

Refer to the exhibit. An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?

Enter the logging console debugging configuration command.

Enter the transport input ssh configuration command.

Enter the terminal monitor exec command.

Enter the logging console debugging configuration command.

Enter the aaa new-model configuration command.

Refer to the exhibit. Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)

Modify access list 1 and allow operations subnet in the access list.

Configure SNMP rw permission in addition to community ciscotest 1.

Configure SNMP rw permission in addition to community ciscotest.

Modify access list 1 and allow operations subnet in the access list.

Modify access list 1 and allow SNMP in the access list.

Configure SNMP rw permission in addition to version 1.

Configure SNMP rw permission in addition to community ciscotest 1.

Refer to the exhibit. Why is the remote NetFlow server failing to receive the NetFlow data?

The flow exporter is configured but is not used.

The flow monitor is applied in the wrong direction.

The flow monitor is applied to the wrong interface.

The destination of the flow exporter is not reachable.

Refer to the exhibit. A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

The route map is applied in the wrong direction.

The local preference value in another neighbor statement is higher than 250.

The local preference value should be set to the same value as the weight in the route map.

The route map is applied in the wrong direction.

The weight value in another neighbor statement is higher than 200.

Refer to the exhibit. an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

A. Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Configure EIGRP to receive 192.168.32.0 route with lower admin distance.

A. Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

A. Configure EIGRP to receive 192.168.32.0 route with lower metric.

A. Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Refer to the exhibit. An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command fixes the issue?

R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1

R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1

R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2

R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1

Refer to the exhibit. A junior engineer updated a branch router configuration. Immediately after the change, the engineer receives calls from the help desk that branch personnel cannot reach any network destinations.Which configuration restores service and continues to block 10.1.1.100/32?

ip prefix-list 102 seq 15 permit 0.0.0.0/32 le 32

ip prefix-list 102 seq 5 permit 0.0.0.0/32 le 32

An engineer configured a leak-map command to summarize EIGRP routes and advertise specifically loopback 0 with an IP of 10.1.1.1.255.255.255.252 along with the summary route. After finishing configuration, the customer complained not receiving summary route with specific loopback address.Which two configurations will fix it? (Choose two.)

Configure access-list 1 permit 10.1.1.0.0.0.0.3.

Configure route-map Leak-Route permit 10 and match access-list 1.

Configure access-list 1 permit 10.1.1.0.0.0.0.3.

Configure access-list 1 permit 10.1.1.1.0.0.0.252.

Configure access-list 1 and match under route-map Leak-Route.

Configure route-map Leak-Route permit 10 and match access-list 1.

Configure route-map Leak-Route permit 20.

Refer to the exhibit. An engineer is monitoring reachability of the configured default routes to ISP1 and ISP2. The default route from ISP1 is preferred if available. How is this issue resolved?

Start IP SLA by defining frequency and scheduling it

Use the icmp-echo command to track both default routes

Use the same AD for both default routes

Start IP SLA by matching numbers for track and ip sla commands

Start IP SLA by defining frequency and scheduling it

Refer to the exhibit. Redistribution is enabled between the routing protocols, and nowPC2 PC3, and PC4 cannot reach PC1. What are the two solutions to fix the problem? (Choose two.)

Filter RIP routes back into RIP when redistributing into RIP in R2

Filter all routes except RIP routes when redistributing into EIGRP in R2.

Filter RIP routes back into RIP when redistributing into RIP in R2

Filter OSPF routes into RIP FROM EIGRP when redistributing into RIP in R2.

Filter all routes except RIP routes when redistributing into EIGRP in R2.

Filter RIP AND OSPF routes back into OSPF from EIGRP when redistributing into OSPF in R2

Filter all routes except EIGRP routes when redistributing into OSPF in R3.

Refer to the exhibit. A company is evaluating multiple network management system tools. Trending graphs generated by SNMP data are returned by the NMS and appear to have multiple gaps. While troubleshooting the issue, an engineer noticed the relevant output. What solves the gaps in the graphs?

Separate the NMS class map in multiple class maps based on the specific protocols with appropriate CoPP actions

Remove the exceed-rate command in the class map.

Remove the class map NMS from being part of control plane policing.

Configure the CIR rate to a lower value that accommodates all the NMS tools

Separate the NMS class map in multiple class maps based on the specific protocols with appropriate CoPP actions

What is a role of route distinguishers in an MPLS network?

Route distinguishers make a unique VPNv4 address across the MPLS network

Route distinguishers define which prefixes are imported and exported on the edge router

Route distinguishers allow multiple instances of a routing table to coexist within the edge router.

Route distinguishers are used for label bindings.

Route distinguishers make a unique VPNv4 address across the MPLS network

What is a function of IPv6 ND inspection?

It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables

It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables

It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables

It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.

It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.

Exhibit: BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?(Choose two)

Configure BGP in the COPP-CRITICAL-7600 ACL

Configure a higher value for CIR under the default class to allow more packets during peak traffic

Configure BGP in the COPP-CRITICAL-7600 ACL

Configure a higher value for CIR under the default class to allow more packets during peak traffic

Configure a higher value for CIR under the class COPP-CRITICAL-7600

Configure a three-color policer instead of two-color policer under class COPP-CRITICAL- 7600

Configure IP CEF to CoPP policy and BGP to work

What is an advantage of using BFD?

It has sub-second failure detection for layer 1 and layer 2 problems.

It detects local link failure at layer 1 and updates routing table.

It detects local link failure at layer 2 and updates routing protocols.

It has sub-second failure detection for layer 1 and layer 3 problems.

It has sub-second failure detection for layer 1 and layer 2 problems.

Refer the exhibit. Which action resolves intermittent connectivity observed with the SNMP trap packets?

Increase the CIR of the mgmt class map

Decrease the committed burst Size of the mgmt class map

Increase the CIR of the mgmt class map

Add a new class map to match TCP traffic

Add one new entry in the ACL 120 to permit the UDP port 161

An engineer configured a company's multiple area OSPF head office router and Site A cisco routers with VRF lite. Each site router is connected to a PE router of an MPLS backbone. After finishing both site router configurations, none of the LSA 3,4 5, and 7 are installed at Site A router. Which configuration resolves this issue?

configure capability vrf-lite on both PE routers connected to Head Office and Site A routers under routtr ospf 1 vrf abc

configure capability vrf-lite on Site A and its connected PE router under router ospf 1 vrf abc

configure capability vrf-lite on Head Office and its connected PE router under router ospf 1 vrf abc

configure capability vrf-lite on both PE routers connected to Head Office and Site A routers under routtr ospf 1 vrf abc

configure capability vrf-lite on Head Office and Site A routers under router ospf 1 vrf abc

Refer to the exhibit. The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host 192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted. Which action resolves the issue without opening full access to this router?

Move the SSH entry to the beginning of the ACL

Temporarily move the permit ip any any line to the beginning of the ACL to see if the flow works

Temporarily remove the ACL from the interface to see if the flow works

Run the show access-list FILTER command to view if the SSH entry has any hit statistic associated with it

What is the role of a route distinguisher via a VRF-Lite setup implementation?

It extends the IP address to identify which VFP instance it belongs to.

It manages the import and export of routes between two or more VRF instances

It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities

It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol capabilities

Cisco 300-410 Practice Test 2 - Free Online Exam Prep & Questions

Question 1 / 40

Which statement about IPv6 RA Guard is true?

It does not offer protection in environments where IPv6 traffic is tunneled.

It cannot be configured on a switch port interface in the ingress direction.

Packets that are dropped by IPv6 RA Guard cannot be spanned.

It is not supported in hardware when TCAM is programmed.

Comment (0)

Cisco 300-410 Practice Test 2

Question

Cisco 300-410 Practice Tests

Practice Tests