Refer to the exhibit. TCP traffic should be reaching host 10.10.10.10/24 via R2. Which action resolves the issue?

Allow TCP in the access list with no changes to the route map

TCP traffic will reach the destination via R2 without any changes

Add a permit 20 statement in the route map to allow TCP traffic

Allow TCP in the access list with no changes to the route map

Set IP next-hop to 10.10.12.2 under the route-map permit 10 to allow TCP traffic.

Refer to the exhibit. After configuring OSPF in R1, some external destinations in the network became unreachable. Which action resolves the issue?

Change the R1 router ID from 10.255.255.1 to a unique value and clear the process.

Clear the OSPF process on R1 to flush stale LSAs sent by other routers.

Change the R1 router ID from 10.255.255.1 to a unique value and clear the process.

Increase the SPF delay interval on R1 to synchronize routes.

Disconnect the router with the OSPF router ID 0.0.0.0 from the network.

What is the function of BFD?

It provides uniform failure detection regardless of media type.

It creates high CPU utilization on hardware deployments.

It negotiates to the highest version if the neighbor version differs.

It provides uniform failure detection on the same media type.

Refer to the Exhibit. R1 and R2 use IGP protocol to route traffic between AS 100 and AS 200 despite being configured to use BGP. Which action resolves the issue and ensures the use of BGP?

Remove distance commands under BGP AS 100 and AS 200.

Configure distance to 100 under the EIGRP process of R1 and R2.

Remove distance commands under BGP AS 100 and AS 200.

Remove distance commands under BGP AS 100.

Configure distance to 100 under the OSPF process of R1 and R2

Refer to the exhibit. Refer to the exhibit. An engineer configured BGP and wants to select the path from 10.77.255.57 as the best path instead of current best path. Which action resolves the issue?

Configure AS_PATH prepend for the current best path

Configure AS_PATH prepend for the desired best path

Configure higher MED to select as the best path.

Configure lower LOCAL_PREF to select as the best path.

Configure AS_PATH prepend for the current best path

What is LDP label binding?

two routers with label distribution session

Refer to the exhibit. Refer to the exhibit. When an FTP client attempts to use passive FTP to connect to the FTP server, the file transfers fail Which action resolves the issue?

Configure to permit TCP ports higher than 1023.

Modify FTP-SERVER access list to remove established at the end.

Modify traffic filter FTP-SERVER in to the outbound direction.

Configure to permit TCP ports higher than 1023.

An administrator attempts to download the pack NBAR2 file using TFTP from the CPE router to another device over the Gi0/0 interface. The CPE is configured as below: The transfer fails. Which action resolves the issue?

Make the permit udp any eq tftp any entry the last entry in the WAN ACL.

Change the WAN ACL to permit the UDP port 69 to allow TFTP

Make the permit udp any eq tftp any entry the last entry in the WAN ACL.

Change the WAN ACL to permit the entire UDP destination port range

Shorten the file name to the 8+3 naming convention.

What is an MPLS LDP targeted session?

label distribution session between non-directly connected neighbors

session between neighbors that are connected no more than one hop away

LDP session established between LSRs by exchanging TCP hello packets

label distribution session between non-directly connected neighbors

LDP session established by exchanging multicast hello packets

Cisco 300-410 Practice Test 9 - Free Online Exam Prep & Questions

DRAG DROP

Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

Cisco 300-410 image Question 1 5015066 10072024125413000

Correct answer:

Cisco 300-410 image answer Question 1 5015066 10072024125413000

Comment (0)

asked 07/10/2024

Tolga Kesici

52 questions

Cisco 300-410 Practice Test 9

Question

Cisco 300-410 Practice Tests

Practice Tests