Refer to the exhibit. Refer to the exhibit. A customer reports that networks in the 10.0.1.0/24 space do not appear in the RIP database. What action resolves the issue?

Remove summarization of 10.0.0.078.

Permit 10.0.1.0/24 address in the ACL.

Remove ACL on R1 blocking 10.0.1.0/24 network.

Configure 10.0.1.0/24 network under RIP.

Refer to the exhibit. Refer to the exhibit. R1 must advertise all loopback interfaces IP addresses to neighbors, but EIGRP neighbors receive a summary route. Which action resolves the issue?

Remove the 10.100.1.0/24 static route.

Redistribute connected routes into EIGRP Enable

Disable auto summarization on R1.

Remove the 10.100.1.0/24 static route.

Refer to the exhibit. Refer to the exhibit. An engineer cannot determine the time of the problem on R1 due to a mismatch between the router local clock and legs. Which command synchronizes the time between new log entries and the local clock on R1?

service timestamps log datetime locatetime msec

service timestamps debug datetime msec show.timezone

service timestamps log datetime locatetime msec

service timestamps datebug datetime localtime msec

service timestamps log datetime msec show-timezone

Refer to the exhibit. Refer to the exhibit. An engineer is investigating an OSPF issue reported by the Cisco DNA Assurance Center. Which action resolves the issue?

One of the interfaces is using the wrong MTU Match interface MTU on both links

One of the neighbor links is down Bring the interface up by running shut and no shut

One of the interfaces is using the wrong MTU Match interface MTU on both links

An ACL entry blocking multicast on the interfaces Allow multicast through the interface ACL

One of the interfaces is using the wrong authentication Match interface authentication on both links

What action is performed for untagged outgoing labels in an MPLS router?

Convert the untagged packet to a labeled packet and forward it to the next router

Convert the incoming MPLS packet to an untagged packet and then do a FIB lookup

Convert the incoming MPLS packet to an untagged packet and then do a RIB lookup.

Convert the untagged packet to a labeled packet and forward it to the next router

Convert the incoming MPLS packet to an IP packet and forward it to the next router.

Refer to the exhibit. Refer to the exhibit. An engineer configured two ASBRs, 10.4.17.6 and 10.4.15.5, in an OSPF network to redistribute identical routes from BGR However, only prefixes from 10.4.17.6 are installed into the routing table on R1. Which action must the engineer take to achieve load sharing for the BGPoriginated prefixes?

The ASBRs are advertising the redistributed prefixes as Type 1 and must be modified to Type 2

The ASBRs are advertising the redistributed prefixes with the iBGP metric and must be modified to Type 1 on ASBR 10.4.17.6.

The ASBRs are advertising the redistributed prefixes with a different admin distance and must be changed to 110 on ASBR 10.4.15.5.

The admin distance of the prefixes must be adjusted to 20 on ASBR 10.4.15.5 to advertise prefixes to R1 identically from both ASBRs.

The ASBRs are advertising the redistributed prefixes as Type 1 and must be modified to Type 2

Refer to the exhibit. Refer to the exhibit. Which configuration resolves the IP SLA issue from R1 to the server?

R6(config)#ip sla responder udp-echo ipaddress 10.60.60.6 po 5000

R6(config)#ip sla 650 R6(config-ip-sla)ff udp-jitter 10.60.60.6

R6(config)#ip sla schedule 10 life forever start-time now

Refer to the exhibit. Refer to the exhibit. The IT manager received reports from users about slow application through network x. which action resolves the issue?

Use the variance 2 command to enable load balancing.

Increase the bandwidth from the service provider.

Move the servers into the users subnet.

Refer to the exhibit. Refer to the exhibit. An engineer noticed that the router log messages do not have any information about when the event occurred. Which action should the engineer take when enabling service time stamps to improve the logging functionality at a granular level?

Configure the tog uptime option

Configure the debug uptime option

Configure the tog uptime option

Refer to the exhibit. An engineer noticed that the router log messages do not have any information about when the event occurred. Which action should the engineer take when enabling service time stamps to improve the logging functionality at a granular level?

Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv4 address and remove process 10 from the global configuration

Replace OSPF process 10 on the interfaces with OSPF process 1 and configure an additional router IO with IPv6 address

Replace OSPF process 10 on the interfaces with OSPF process 1. and remove process 10 from the global configuration

Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv6 address and remove process 10 from the global configuration

Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv4 address and remove process 10 from the global configuration

How is a preshared key "Testíí for all the remote VPN rooters configured In a DMVPN using GRE over IPsec set up?

crypto isakmp key Test address 0.0.0.0 0.0.0.0

authentication pre-share Test address 0.0.0.0 0.0.0.0

set pre-share Test address 0.0.0.0 0.0.0.0

crypto Ipsec key Test address 0.0.0.0 0.0.0.0

crypto isakmp key Test address 0.0.0.0 0.0.0.0

Refer to the exhibit. An engineer configures two ASBRs 10 4 17.6 and 10 4 15 5 in an OSPF network to redistribute routes from EIGRP However, both ASBRs show the EIGRP routes as equal costs even though the next-hop router 10 4 17 6 is closer to R1How should the network traffic to the EIGRP prefixes be sent via 10 4.17.6?

The redistributed prefixes should be advertised as Type 1

The administrative distance should be raised to 120 from the ASBR 10.4.15 5.

The redistributed prefixes should be advertised as Type 1

The ASBR 10 4 17 6 should assign a tag to match and assign a lower metnc on R1

The administrative distance should be raised to 120 from the ASBR 104.17.6

The admitstrative distance should be raised to 120 from the ASBR 104 15.5.

The redistributed prefixes should be advertised as Type 1.

The ASBR 10 4 17 6 should assign a tag to match and assign a tower metnc on R1

The administrative distance should be raised to 120 from the ASBR 104 17 6

An engineer configured routing between multiple OSPF domains and introduced a routing loop that caused network instability. Which action resolves the problem?

Set a tag using the redistribute command toward a domain and deny inbound m the other domain by a matching tag

Set a tag using the redistribute command toward a different domain and deny the matching tag when exiting from that domain

Set a tag using the network command in a domain and use the route-map command to deny the matching lag when exiting toward a different domain

Set a tag using the network command in a domain and use the route-map command to deny the matching tag when entering into a different domain

Refer to the exhibit. Refer to the exhibit. A network engineer is troubleshooting a failed link between R2 and R3 No traffic loss is reported from router R5 to HQ Which command fixes the separated backbone?

R3(config-router)#no area 21 stub

R2(config-router)#no area 21 stub

R2(config_router)#area 21 virtual-link 192.168.125.5

R3(config-router)#area 21 virtual-link 192.168.125.5

R3(config-router)#no area 21 stub

Refer to the exhibit. Refer to the exhibit. An administrator must harden a router, but the administrator failed to test the SSH access successfully to the router. Which action resolves the issue?

SSH syntax must be ssh -I user ip to log in to the remote device

Configure SSH on the remote device to log m using SSH

SSH syntax must be ssh -I user ip to log in to the remote device

Configure enable secret to log in to the device

SSH must be allowed with the transport output ssh command

Refer to the exhibit. A network administrator is troubleshooting OSPF adjacency issue by going through the console logs in the router, but due to an overwhelming log message stream it is impossible to capture the problem Which two commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved? (Choose two)

debug condition session-id ADJCHG

Refer to the exhibit. Refer to the exhibit A network engineer received a call from the vendor for a failed attempt to remotely log in to their managed rooter loopback interface from 192 168.40 15 Which action must the network engineer take to resolve the issue?

The EIGRP configuration must be updated to include a network statement for loopback 100

The IP access list VENDOR must be applied to interface loopback 100

The time-range configuration must be changed to use absolute instead of periodic

The EIGRP configuration must be updated to include a network statement for loopback 100

The source IP summarization must be updated to include the vendor source IP address

Refer to the exhibit. Refer to the exhibit. An administrator can log in to the device using Telnet but the attempts to log in to the same device using SSH with the same credentials fail Which action resolves this issue?

Configure SSH service on the router

Configure transport input all on the VTY lines to allow SSH

Configure to use the Telnet user database for SSH as well

Configure the VTY lines with login local

Refer to the exhibit. An administrator is configuring a GRE tunnel to establish an EIGRP neighbor to a remote router. The other tunnel endpoint is already configured. After applying the configuration as shown, the tunnel started flapping. Which action resolves the issue?

Stop sending a route matching the tunnel destination across the tunnel.

Modify the network command to use the Tunne10 Interface netmask.

Advertise the Loopback0 interface from R2 across the tunnel.

Readdress the IP network on the Tunne10 on both routers using the /31 netmask.

A network administrator is troubleshooting a failed AAA login issue on a Cisco Catalyst c3560 switch.When the network administrator tries to log in with SSH using TACACS+ username and password credentials, the switch is no longer authenticating and is failing back to the local account. Which action resolves this issue?

Configure ip tacacs source-interface GigabitEthernet 1/1

Configure ip tacacs source-ip 192.168.100.55

Configure ip tacacs-server source-ip 192.168.100.55

Configure ip tacacs-server source-interface GigabitEthernet 1/1

Refer to the exhibit. Refer to the exhibit. After reloading the router an administrator discovered that the interface utilization graphs displayed inconsistencies with their previous history in the NMS. Which action prevents this issue from occurring after another router reload in the future?

Configure SNMP interface index persistence on the router

Rediscover all the router interfaces through SNMP after the router is reloaded

Save the router configuration to startup-config before reloading the router

Configure SNMP to use static OlDs referring to individual router interfaces

Configure SNMP interface index persistence on the router

Refer to the exhibit. R1 cannot receive the R2 Interfaces with individual prefixes. What must be reconfigured to advertise R2 Interfaces to R1?

ElGRP process on R2 with the command stub summary connected

EIGRP process on R2 by removing the stub command Keyword summary

interface FastEthernet0/1 on R2 with an EIGRP summary for all three loopback prefixes

EIGRP process on R2 with the command stub summary receive-only

ElGRP process on R2 with the command stub summary connected

What is a characteristic of IPv6 RA Guard?

It filters rogue RA broadcasts from connected hosts

RA messages are allowed from the host port to the switch

It is unable to protect tunneled traffic

It filters rogue RA broadcasts from connected hosts

It is supported on the egress direction of the switch

Refer to the exhibit. An engineer applies a prefix-list filter that filters most of the network 10 prefixes instead of allowing them. Which action resolves the issue?

Modify the Ip prefix-list ElGRP seq 20 permit 0.0.0.0/0 le 32 command.

Modify the ip prefix-list ElGRP seq 10 permit 10.0.0.0/8 le 9 command.

Modify the command Modify the Ip prefix-list ElGRP seq 10 permit 10.0.0.0/8 le 32 command.

Modify the Ip prefix-list ElGRP seq 20 permit 0.0.0.0/0 le 32 command.

Modify the ip prefix-list ElGRP seq 20 permit 10.0.0.0/8 ge 9 command

Refer to the exhibit. Which action makes 10.1.3.2 the feasible successor to reach 10. 200. 1 0/24 for location S42T447E33F95?

Increase path bandwidth lower than 1011 2 and lower than 1012 2 between RtrA and the destination

Increase path bandwidth higher than 10.1 2 2 and lower than 101.1.2 between RtrA and the destination.

Increase path bandwidth higher than 1011 2 and lower than 1012 2 between RtrA and the destination

Increase path bandwidth higher than 10.1 2 2 and higher than 10.1.1.2 between RtrA and the destination

Refer to the exhibit. Refer to lhe exhibit An engineer must filter EIGRP updates that are received to block all 10 10 10.0/24 prefixes The engineer tests the distribute list and finds one associated prefix. Which action resolves the issue?

There is a permit in the ACL that allows this prefix into EI6RP. The ACL should be modified to deny 10.10.10.0 0.0.0.255.

There is a permit in the route map that allows this prefix A deny 20 statement is required with a match condition to match a new ACL that denies all prefixes

There is a permit in the ACL that allows this prefix into EI6RP. The ACL should be modified to deny 10.10.10.0 0.0.0.255.

There is a permit in the route map that allows this prefix A deny 20 statement is required with no match condition to block the prefix.

There is a permit in the ACL that allows this prefix into EIGRP. The ACL should be modified to deny 10.10.10.0 255.255.255.0.

Refer to the exhibit. Refer to the exhibit. An engineer applied filter on R1 The interface flapped between R1 and R2 and cleaning the BGP session did not restore the BGP session and failed Which action must the engineer take to restore the BGP session fromR2 to R1?

ICMPv6 must be permitted by the IPv6 traffic filter

Apply the IPv6 traffic filter in the outbound direction on the interface

ICMPv6 must be permitted by the IPv6 traffic filter

Enable the BGP session, which went down when the session was cleared.

Swap the source and destination IP addresses in the IPv6 traffic filter

What is the purpose of an OSPF sham-link?

to correct OSPF backdoor routing when OSPF is used as the PE-PE connection protocol m an MPLS VPN network

to allow intra-area routing when OSPF is used as the PE-CE connection protocol in an MPLS VPN network

to correct OSPF backdoor routing when OSPF is used as the PE-CE connection protocol *i an MPLS VPN network

to correct OSPF backdoor routing when OSPF is used as the PE-PE connection protocol m an MPLS VPN network

to allow inter-area routing when OSPF is used as the PE-CE connection protocol in a MPLS VPN network

Refer to the exhibit. Refer to the exhibit. An administrator must upload the packages conf Me to an FTP server. However, the FTP server rejected anonymous service and required users to authenticate What are the two ways to resolve the issue? (Choose two.)

Use is ftp username and ip ftp password configuration commands to specify valid FTP server credentials.

Enter the FTP server credentials directly In the FTP URL using the ftp://username:passwordQ192.0.2.40/ syntax .

Use is ftp username and ip ftp password configuration commands to specify valid FTP server credentials.

Use the copy flash:packages.conf scp: command instead and enter the FTP server credentials when prompted.

Enter the FTP server credentials directly In the FTP URL using the ftp://username:passwordQ192.0.2.40/ syntax .

Create a user on the rooter matching the username and password on the FTP server and log in before attempting the copy

Use the copy flash-packages conf ftp: command instead and enter the FTP server credent-ais when prompted.

Cisco 300-410 Practice Test 12 - Free Online Exam Prep & Questions

Refer to the exhibit.

Cisco 300-410 image Question 441 111387 10072024005414000000

Refer to the exhibit. A network engineer cannot remote access R3 using Telnet from switch S1. Which action resolves the issue?

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-410 Practice Test 12

Question

Cisco 300-410 Practice Tests

Practice Tests