An engineer must Configure a new Cisco UCS B-Series infrastructure with a Cisco 5108 chassis. The configuration must meet these requirements:* The setup must use aggregation between Cisco UCS Fabric Interconnects and I/O modules.* The implementation requires four 10 GbE connections per I/O module.* The Cisco UCS Fabric Interconnects must support uplinks of different speeds for future expansion.Which two steps must be taken to meet these requirements? (Choose two.)

Set IOM link pinning in Global Policies.

Configure unified ports for the chassis.

Reacknowledge the chassis after the initial discovery.

Set IOM link pinning in Global Policies.

Configure unified ports for the chassis.

Set Link Group Preference to Port Channel.

Disable Auto Configure Server Port.

What is a feature of an electronic programmable logic device upgrade on a Cisco MDS 9000 Series Switch?

Only the modules that are being upgraded are disrupted.

An EPLD upgrade is disruptive on all modules.

The standby supervisor module can perform the upgrade.

An EPLD upgrade is nondisruptive on all modules.

An engineer implements an Application Performance Monitoring (APM) solution. The solution runs in a vSphere infrastructure where the vSwitch support for promiscuous mode is disabled for security reasons. As a result, the final implementation must receive a copy of bidirectional traffic to a load balancer that is connected to a Cisco Nexus 93108 Series Switch. The APM solution supports GRE encapsulated traffic. Which configuration must be applied to the switch to meet this requirement?

configure terminal monitor session 1 type erspan-source erspan-id 1 destination ip 10.1.1.1 source interface ethernet 1/9 both vrf default no shut

interface vlan1 switchport monitor destination ip 10.1.1.1 exit monitor session 1 rx monitor session 1 tx source interface ethernet1/9

monitor session 1 both source interface ethernet 1/9 destination interface ethernet 1/12 erspan-id 1 vrf mgmt0 filter vlan 3 no shut

configure terminal monitor session 1 type erspan-source erspan-id 1 destination ip 10.1.1.1 source interface ethernet 1/9 both vrf default no shut

interface ethernet 1/9 erspan-id 1 monitor session 1 type erspan-source interface mgmt0 monitor session 1 type erspan-destination destination ip 10.1.1.1 no shut

Refer to the exhibit. What happens to the VRRP configuration when the router SW9621-2 becomes operational?

The SW9621-2 router becomes a new active master.

The SW9621-1 router becomes a new active master after 3 seconds.

The SW9621-1 router remains an active master.

The SW9621-2 router becomes an active master after 3 seconds.

What is the impact of a nondisruptive upgrade on fabric and modular switches?

During the upgrade, new devices cannot log in to the fabric.

The upgrade disrupts the control plane for more than 120 seconds.

During the upgrade, new devices cannot log in to the fabric.

If a zone server merge is in progress, the upgrade continues without interruption.

When the installation is complete, the system BIOS must be updated.

Refer to the exhibit. Refer to the exhibit. An engineer uses Python in Cisco NX-OS guest shell to retrieve the configuration of the EIGRP ASN on interface eth1/1.The engineer has written this script:>>> import json>>> from cli import*Which command set must be used to retrieve the value of the 'asn' key?

>>> output = json.loads(clid('show ip eigrp neighbors')) >>> output['asn']

>>> output = json.loads(clid('show ip eigrp neighbors')) >>> output['TABLE_asn']['ROW_asn']['asn']

>>> output = json.dumps(clid('show ip eigrp neighbors')) >>> output['TABLE_asn']['ROW_asn']['asn']

>>> output = json.dumps(clid('show ip eigrp neighbors')) >>> output['asn']

>>> output = json.loads(clid('show ip eigrp neighbors')) >>> output['asn']

Cisco 350-601 Practice Test 13 - Free Online Exam Prep & Questions

An engineer must replace a defective fabric interconnect with the same model. The system must be restored, including the database of locally created users. The equivalent Cisco UCS Manager software version must be used. Which backup type must be used to meet these requirements?

Become a Premium Member for full access

Unlock Premium Member

Cisco 350-601 Practice Test 13

Question

Cisco 350-601 Practice Tests

Practice Tests