ExamGecko
Home / Huawei / H12-811_V1.0 / List of questions
Ask Question

Huawei H12-811_V1.0 Practice Test - Questions Answers, Page 5

List of questions

Question 41

Report Export Collapse

As shown in the figure, a static NAT command is deployed on router R1. When the PC accesses the Internet, the destination address in the data packet will not change. ()(True or False)

Huawei H12-811_V1.0 image Question 41 33616 09182024192851000000

True
True
False
False
Suggested answer: A
asked 18/09/2024
Michael Amann
42 questions

Question 42

Report Export Collapse

The ACL configuration information of a certain router is shown in the figure. Which of the following statements is correct? () (Single-choice question)

Huawei H12-811_V1.0 image Question 42 33617 09182024192851000000

The packet whose source IP address is 192.168.1.254 is matched by the permit rule
The packet whose source IP address is 192.168.1.254 is matched by the permit rule
Packets with source IP addresses of 192.168.1.1 and 192.168.1.254 are matched by the permit rule
Packets with source IP addresses of 192.168.1.1 and 192.168.1.254 are matched by the permit rule
The packet with the source IP address of 192.168.1.1 is matched by the pemit rule
The packet with the source IP address of 192.168.1.1 is matched by the pemit rule
The packet with the source IP address 192.168.1.1 is matched by the deny rule
The packet with the source IP address 192.168.1.1 is matched by the deny rule
Suggested answer: C
asked 18/09/2024
Reece Scarley
46 questions

Question 43

Report Export Collapse

The administrator made the configuration on the router as shown in the figure. At the same time, the administrator wants to assign a shorter lease period to the DHCP address. Which of the following commands should be used? () (Single-choice question) ip pool pooll netyork10.10.10.0ask255.255.255.0 gateway-list 10.10.10.1

Lease 0
Lease 0
Dhcp select relay
Dhcp select relay
Lease day 0 hour 10
Lease day 0 hour 10
Lease 24
Lease 24
Suggested answer: C
asked 18/09/2024
Bogdan Karolic
49 questions

Question 44

Report Export Collapse

The network is shown in the figure. Which router is the BDR in this network? () (Single-choice question)

Huawei H12-811_V1.0 image Question 44 33619 09182024192851000000

Router B
Router B
No BDR
No BDR
Router C
Router C
Router A
Router A
Suggested answer: B
asked 18/09/2024
Kamran Kamran
49 questions

Question 45

Report Export Collapse

As shown in the figure below, in the MAC address table of the network. SWA and SWB, which of the MAC addresses, VLANs, and ports are correct? () (Single-choice question)

Huawei H12-811_V1.0 image Question 45 33620 09182024192851000000

SWB:MAC Address VLANPortMAC-AMAC-BMAC-C100200100GEC/0/3GEC/0/3GEC/0/1
SWB:MAC Address VLANPortMAC-AMAC-BMAC-C100200100GEC/0/3GEC/0/3GEC/0/1
SWA:MAC AddressVLANPortMAC-AMAC-BMAC-C10GEC/O/1GEC/0/2GEC/0/320100
SWA:MAC AddressVLANPortMAC-AMAC-BMAC-C10GEC/O/1GEC/0/2GEC/0/320100
SWB:MAC Address VLANPortMAC-AMAC-BMAC-C10GEC/0/3GEC/0/3GEC/0/120100
SWB:MAC Address VLANPortMAC-AMAC-BMAC-C10GEC/0/3GEC/0/3GEC/0/120100
SWA:MACAddress VLANPortMAC-AMAC-BMAC-C10GEC/0/320GEC/0/3GEC/0/3100
SWA:MACAddress VLANPortMAC-AMAC-BMAC-C10GEC/0/320GEC/0/3GEC/0/3100
Suggested answer: C
asked 18/09/2024
B Erol
63 questions

Question 46

Report Export Collapse

The switch G0/0/1 port configuration information is shown in the figure. Which VLAN data frame does the switch forward without VLANTAG? ? () (Single-choice question)

Huawei H12-811_V1.0 image Question 46 33621 09182024192851000000

10
10
30
30
20
20
40
40
Suggested answer: A
asked 18/09/2024
Victor Gouveia Pennella
47 questions

Question 47

Report Export Collapse

As shown in the figure, the G0/0/0 and G0/0/1 interfaces of RTA are connected to two different network segments. RTA is the gateway of these two networks. Before host A sends data to host C, will it send an ARP Request to obtain O's MAC address? () (Single-choice question)

Huawei H12-811_V1.0 image Question 47 33622 09182024192851000000

SW
SW
Host C
Host C
G0/0/1 interface of RTA
G0/0/1 interface of RTA
G0/0/0 interface of RTA
G0/0/0 interface of RTA
Suggested answer: D
asked 18/09/2024
Jermaine Wells
43 questions

Question 48

Report Export Collapse

The two switches shown in the figure below have both enabled the STP protocol. Which port will eventually be in the Blocking state? ()

Huawei H12-811_V1.0 image Question 48 33623 09182024192851000000

SWA's G0/0/3 port
SWA's G0/0/3 port
SWA's G0/0/2 port
SWA's G0/0/2 port
G0/0/2 port of SWB
G0/0/2 port of SWB
G0/0/3 port of SWB
G0/0/3 port of SWB
Suggested answer: D
asked 18/09/2024
Tatiana Castillo
36 questions

Question 49

Report Export Collapse

In the network as shown in the figure below, host A logs in to router A through Telnet. Then obtains the configuration file of router B through FTP on the remote interface. At this time, how many TCP connections does router A have? () (Single-choice question)

Huawei H12-811_V1.0 image Question 49 33624 09182024192851000000

4
4
1
1
3
3
2
2
Suggested answer: C
asked 18/09/2024
Nathalie Yip
41 questions

Question 50

Report Export Collapse

As shown in the picture. About OSPF topology and configuration. Which of the following statements is correct? () (Single-choice question)

Huawei H12-811_V1.0 image Question 50 33625 09182024192851000000

R1 and R2 can establish a stable OSPF neighbor relationship
R1 and R2 can establish a stable OSPF neighbor relationship
R1 is more likely to become DR than R2, because its interface DR priority value is smaller
R1 is more likely to become DR than R2, because its interface DR priority value is smaller
As long as the interface network type of R1 is restored to the default broadcast type, R1 and R2 can establish a stable neighbor relationship
As long as the interface network type of R1 is restored to the default broadcast type, R1 and R2 can establish a stable neighbor relationship
As long as the interface network type of R1 is restored to the default broadcast type, and the hello time is adjusted to 10s, R1 and R2 can establish a stable neighbor relationship
As long as the interface network type of R1 is restored to the default broadcast type, and the hello time is adjusted to 10s, R1 and R2 can establish a stable neighbor relationship
Suggested answer: D
asked 18/09/2024
EduBP srl EduBP
46 questions
Total 984 questions
Go to page: of 99
Search

Related questions