Cisco 350-501 Practice Test - Questions Answers, Page 25
Question list
List of questions
Related questions
An engineer must apply an 802.1ad-compliant configuration to a new switchport with these requirements; The switchport must tag all trame when it enters the port The switchport Is expected to provide the same level of service to traffic from any customer VLAN Which configuration must the engineer use?
Option A
Option B
Option C
Option D
Refer to the exhibit A network engineer is in the process of implementing IS-IS Area 1 and Area 2 on this network to segregate traffic between different segments of the network The hosts in the two new areas must maintain the ability to communicate with one another In both directions. Which additional change must be applied?
Reconfigure either R3 or R4 as a Level 1/Level 2 router.
Reconfigure routers R1, R2 R5. and R6 as Level 1/Level 2 routers.
Reconfigure routers R2 and R5 as Level 1/Level 2 routers.
Reconfigure routers R4, R5 and R6 as Level 1 routers
A network engineer must configure a router for Flexible NetFlow IPFIX export. The IP address of the destination server is 172.17.12.1 The source address must be set to the Loopback0 IPv4 address and exported packets must be set to DSCP CS3. The TTL must be 64 and the transport protocol must be set to UDP with destination port 4739. Which configuration must the engineer apply to the router?
Option A
Option B
Option C
Option D
Which action does the ingress VTEP perform on traffic between EVPN VXLAN overlays?
routing and tunneling when doing symmetric IRB
routing when doing asymmetric IRB
routing and bridging when doing asymmetric IRB
bridging when doing symmetric IRB
Refer to the exhibit. An organization s network recently experienced several significant outages due to device failures. The network administrator just moved the network devices to a new central data center, and packets are switched using labels. The administrator Is now implementing NSF on the network to reduce potential risk factors in the event of another outage. Which task must the administrator perform on each router as part of the process?
Remove route filtering to speed repopulation of the link-state database
Copy the router s existing state information and share the file with its peers to enable BGP soft resets
Implement MPLS to forward packets while the RIB updates after a faliover.
Implement Graceful Restart to mitigate the delay in MPLS LDP synchronization when the IGP starts up.
A network administrator is planning a new network with a segment-routing architecture using a distributed control plane. How is routing information distributed on such a network?
Each segment is signalled by an SR controller, but each segment makes Its own steering decisions based on SR policy.
Each segment is signalled by MPLS, and each segment makes steering decisions based on the routing policy pushed by BGP.
Each segment is signalled by an SR controller that makes the steering decisions for each node.
Each segment is signalled by a compatible routing protocol and each segment makes its own steering decisions based on SR policy.
When Cisco lOS XE REST API uses HTTP request methods what is the purpose of a PUT request?
retrieves the specified resource or representation
submits data to be processed to the specified resource
updates the specified resource with new information
creates a new resource
Refer to me exhibit. An engineer started lo configure a router for OSPF. Which configuration must me engineer perform on me router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?
Option A
Option B
Option C
Option D
Refer to the exhibit.
A network engineer must meet these requirements to provide a connects, solution:
The customer connected to Area 2 needs to access the application in Area 1 on the 10.10.10.0/24 subnet The Customer must not have access to the 20.10 30.0/24 subnet.
The service provider must make sure that the Area 2 routing database limits the number of IP addresses in the routing table
Which two configurations must be implemented to meet the requirements? (Choose two)
Set a tag value of 200 to match the summary address 10.0.0/16 on R2.
Set a tag value of 200 to match the summary address 10.0.0.0/16 on R3.
Apply the route map for tag 200 and leak Level 2 routes into Level 1 Area 2 on R3
Apply the route map for tag 200 and teak Level 2 routes into Level 1 Area 2 on R4.
Set a tag value of 200 to match the summary address 10.0.0./16 on R1.
Refer to the exhibit. EIGRP a running across the core lo exchange Internal routes, and each router maintains 6GP adjacency with the other routers on the network. An operator has configured static routes on the edge routers R1 and R2 for IP address 10.0.1.1. which is used as a black hole route as shown. Which configuration should the operator Implement to me management rouler to create a route map that will redistribute lagged static routes into BGP and create a static route to blackhole traffic with tag 777 that Is destined to server at 192.168.10.100?
Option A
Option B
Option C
Option D
Question