Cisco 350-501 Practice Test - Questions Answers, Page 28
Question list
List of questions
Related questions
DRAG DROP
Drag and drop the OSPF and IS-IS Cisco MPLS TE extensions from the left to their functional descriptions on the right.
DRAG DROP
Drag and drop the methods of Cisco MPLS TE tunnel traffic assignment from the left onto their characteristics on the right.
DRAG DROP
Drag and drop the functions from the left onto the correct Path Computation Element Protocol roles on the right.
DRAG DROP
Drag and drop the multicast concepts from the left onto the correct descriptions on the right.
DRAG DROP
A network engineer is adding an additional 10Gbps link to an existing 2x10Gdps LACP-based LAG to augment its capacity. Network standards require a bundle interface to be taken out of service if one of its member links goes down, and the new link must be added with minimal impact to the production network. Drag and drop the tasks that the engineer must perform from the left into the sequence on the right. Not all options are used.
DRAG DROP
Drag and drop the message types from the left onto the target field of the message originator on the right.
DRAG DROP
Drag and drop the BGP Best Path Algorithm rules from the left into the corresponding order of importance on the right.
Refer to the exhibit.
An administrator working for large ISP must connect its two POP sites to provide internet connectivity to its customers. Which configuration must the administrator perform to establish an iBGP session between routers PE1 on POP site 1 and PE2 on POP site 2?
PE2#configure terminal
PE2(config)#router bgp 65111
PE2(config-router)#no neighbor172.18.10.1 shutdown
PE2(config-router)#end
PE1#configure terminal
PE1(config)#router bgp 65111
PE1(config-router)#no neighbor 172.19.10.10 shutdown
PE1(config-router)#end
PE1#configure terminal
PE1(config)#router bgp 65111
PE1(config-router)#address-family ipv4 unicast
PE1(config-router-af)#neighbor 172.19.10.10 activate
PE1(config-router-af)#end
PE2#configure terminal
PE2(config)#router bgp 65111
PE2(config-router)#address-family ipv4 unicast
PE2(config-router-af)#neighbor 172.18.10.1 activate
PE2(config-router-af)#end
Refer to the exhibit.
Refer to the exhibit. An Ethernet access provider is configuring routers PE-1 and PE-2 to provide EAccess EVPL service between UNI and ENNI. ENNI service multiplexing is based on 802.1ad tag 150, and service-multiplexed UNI is based on 802.1q tag 10. Which EFP configurations must the provider implement on PE-1 and PE-2 to establish end-to-end connectivity between CE-1 and CE-2?
On PE-1:
interface GigabitEthernet2
service instance 100 ethernet
encapsulation dot1ad 150
rewrite ingress tag pop 1 symmetric
On PE-2:
interface GigabitEthernet2
service instance 2 ethernet
encapsulation dot1q 10
On PE-1:
interface GigabitEthernet2
service instance 100 ethernet
encapsulation dot1q 150
rewrite ingress tag pop 1 symmetric
On PE-2:
interface GigabitEthernet2
service instance 2 ethernet
encapsulation dot1q 10
On PE-1:
interface GigabitEthernet2
service instance 100 ethernet
encapsulation dot1ad 150 dot1q 10
rewrite ingress tag pop 2 symmetric
On PE-2:
interface GigabitEthernet2
service instance 2 ethernet
encapsulation dot1q 10
On PE-1:
interface GigabitEthernet2
service instance 100 ethernet
encapsulation dot1ad 150
rewrite ingress tag pop 1 symmetric
On PE-2:
interface GigabitEthernet2
service instance 2 ethernet
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
What are two features of stateful NAT64? (Choose two.)
It uses address overloading.
It provides 1:N translations, so it supports an unlimited number of endpoints.
It requires IPv4-translatable IPv6 address assignments.
It requires the IPv6 hosts to use either DHCPv6-based address assignments or manual address assignments.
It provides 1:1 translation, so it supports a limited number of endpoints.
Question