Cisco 300-615 Practice Test - Questions Answers, Page 12
Question list
List of questions
Related questions
Refer to the exhibit.
The scheduler was configured to save the running-config automatically daily. However, the scheduler is returning the error presented. Which action resolves the issue?
Reconfigure the scheduler using the admin user
Use the kstack attribute for copying the configuration file
Remove vrf management from the command
Change the file transfer protocol to TFTP in scheduler job
Refer to the exhibit.
RBAC is configured on the MDS switch for a new SAN administrator engineer to work on the FSPF configuration. However, after the configuration is applied the engineer who was assigned the FSPF_Admin role cannot perform any configuration changes. Which action resolves the issue?
Write rule 2 before rule 1
Remove rule 1 from the role
Configure the switch license for RBAC
Reload the switch
Refer to the exhibit.
An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?
Commit the active database with the port-security database copy vsan 1 command
Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command
Disable CFS distribution with the no port-security distribute vsan 1 command
Commit the changes with the port-security commit copy vsan 1 command
Refer to the exhibit.
A network administrator must delete a feature group from a Cisco Nexus 5000 Series Switch. Which action resolves the issue?
Detach the association with the no rule command within the role configuration mode
Detach the association with the no role command within the feature-group configuration mode
Detach the association with the no rule command within the feature-group configuration
Detach the association with the no role command within the role configuration mode
Refer to the exhibit.
An engineer discovers that if the vPC peer link goes down, half of the devices in VLAN 20 experience connectivity issues with the external networks Which action resolves the issue?
Configure a dedicated Layer 3 link between vPC peers
Allow non-vPC VLANs on a second trunk between the two vPC peers
Add the non-vPC SVIs in the dual-active exclude VLAN list
Exclude the non-vPC VLANs from vPC peer link
Refer to the exhibit.
An engineer is troubleshooting the connectivity between Server-1 and Server-2. Which action resolves the connectivity issue?
Enable BGP advertise pip feature on both leaf switches
Configure the same source IP address on NVE and virtual peer link on leaf switches
Classify CFS messages for strict priority queue on spine switches
Change all ports on spine switches as port-type fabric
Refer to the exhibit.
A client reports that the routing protocol neighborship fails to start between two Cisco Nexus switches, N9K-1 and N9K-2. Which action resolves the issue?
Add OSPF routing configuration to interface e1/1 on both Cisco Nexus switches
Configure a unicast access list to allow the negotiation between N9K-1 and N9K-2
Configure a multicast access list to allow the negotiation between N9K-1 and N9K-2
Add MTU configuration to interface e1/1 on both Cisco Nexus switches
What does this adapter output indicate? adapter 1/6/1 (fls): 2# lunlist 9 vnic: 9 lifid: 6
- FLOGI State : flogi est (fc_id Oxac0e04)
- PLOGI Sessions
- WWNN 50:0a:09:83:8d:53:43:44 WWPN 50:0a:09:83:8d:53:43:44 fc_id 0x000000
- LUN's configured (SCSI Type, Version, Vendor, Serial No.)
- LUN ID: Ox0000000000000000 access failure
-REPORT LUNs Query Response
- Nameserver Query Response
-WWPN: 54:b1:6a:94:64:3e:73:44
The configured initiator LUN ID does not match the configured target LUN ID
The target device configuration does not allow the initiator to access the LUN
The port types between the target and initiator are incorrectly configured
The target of the configured zone does not match the target of the configured boot order
Refer to the exhibit.
The job fails to run. Which action resolves the issue?
Configure an NTP server
Add a start time to the script
Renew the feature license
Enable the feature required
Refer to the exhibit.
The FCoE traffic fails to traverse the vfc2 interface. The VSAN 102 is configured for vfc2. Which action resolves the issue?
Enable LLDP on the interface vfc2
Activate DCBX on the N9K switch
Activate DCBX on the interface e101/1/2
Enable LLDP on the neighbor switch
Question