ExamGecko
Home / Cisco / 300-615 / List of questions
Ask Question

Cisco 300-615 Practice Test - Questions Answers, Page 8

Add to Whishlist

List of questions

Question 71

Report Export Collapse

A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

Set the same WWNN pools for vHBA adaptor

Suggested answer: C
asked 07/10/2024
Trung Phan
52 questions

Question 72

Report Export Collapse

The external routes fail to propagate to leaf switches in Cisco ACI fabric Which two actions resolve the issue? (Choose two.)

Enable the VTEP pool in the fabric

Enable the VTEP pool in the fabric

Assign an MP-BGP AS number to the fabric.

Assign an MP-BGP AS number to the fabric.

Specify the spine nodes as route reflectors

Specify the spine nodes as route reflectors

Associate the correct contract to the L30ut.

Associate the correct contract to the L30ut.

Configure an MP-BGP area.

Configure an MP-BGP area.

Suggested answer: B, C
asked 07/10/2024
Laurence Peterson
35 questions

Question 73

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 73 113254 10072024010022000000

The vPC between switch1 and switch2 does not work. Which two actions resolve the problem?

(Choose two.)

Configure the IP address on the interface.

Configure the IP address on the interface.

Activate VLANs on the vPC.

Activate VLANs on the vPC.

Configure one of the switches as primary for the vPC.

Configure one of the switches as primary for the vPC.

Correct the configuration of the vPC peer link and the vPC peer keepalive.

Correct the configuration of the vPC peer link and the vPC peer keepalive.

Match the vPC domain ID between the two devices.

Match the vPC domain ID between the two devices.

Suggested answer: D, E
Explanation:

Both β€œvPC peer link” and β€œPeer keepalive link” are down. So, D is correct.

SW1 is using vPC domain ID 500, which SW2 is using 20. They must match. So, E is correct.

asked 07/10/2024
Natcha Koopipat
47 questions

Question 74

Report Export Collapse

Refer to the exhibits.

Cisco 300-615 image Question 74 113255 10072024010022000000

An engineer troubleshoots switch N5K1, which fails to receive traffic from the file server Which set of actions resolves this problem?

Bind native VLAN 10 with Ethemet1/10 and allow VSAN 101 in trunk configuration.

Bind native VLAN 10 with Ethemet1/10 and allow VSAN 101 in trunk configuration.

Assign native VLAN 10 with vfc111 and allow VLAN 1101 in trunk configuration.

Assign native VLAN 10 with vfc111 and allow VLAN 1101 in trunk configuration.

Bind native VLAN 10 with Ethemet10/1/1 and allow VLAN 10 in trunk configuration

Bind native VLAN 10 with Ethemet10/1/1 and allow VLAN 10 in trunk configuration

Assign native VLAN 10 with fc2.'l - 2 and allow VLAN 10 in trunk configuration.

Assign native VLAN 10 with fc2.'l - 2 and allow VLAN 10 in trunk configuration.

Suggested answer: C
asked 07/10/2024
Freddy Rojas
42 questions

Question 75

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 75 113256 10072024010022000000

A network engineer traces the packet flow from the Veth991 of a blade server toward the core switch. The switch reports performance issues. What is the role of the interface Eth1/7?

IOM network interface

IOM network interface

fabric interconnect uplink interface

fabric interconnect uplink interface

IOM host interface

IOM host interface

server interface

server interface

Suggested answer: B
Explanation:

E1/7 is border interface, which is used as uplink. All other veth interfaces are SIF, which stands for Server Interface.

asked 07/10/2024
Rio Ordonez
43 questions

Question 76

Report Export Collapse

A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

A. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels 2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.

3) Check for runtime link down status

4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.

2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.

3) Check for runtime link down status

4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.

2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.

3) Check for runtime link down status

4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.

2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.

3) Check for runtime link down status.

4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.

2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.

3) Check for runtime link down status.

4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.

2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.

3) Check for runtime link down status.

4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.

2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.

3) Check for runtime link down status.

4) Reseat the affected IOM.

Suggested answer: B
Explanation:

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/UCSTroubleshooting_chapter_01001.html

Cisco 300-615 image Question 76 explanation 113257 10072024010022000000

asked 07/10/2024
Ali Reza Farahnak
55 questions

Question 77

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 77 113258 10072024010022000000

Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address onSWITCH-VTEP-2 and then dropped. Which action resolves the issue?

Configure a distributed anycast gateway on both peers

Configure a distributed anycast gateway on both peers

Configure ip arp synchronize under the VPC domain on both peers

Configure ip arp synchronize under the VPC domain on both peers

Configure peer-gateway under the VPC domain on both peers

Configure peer-gateway under the VPC domain on both peers

Configure a different secondary IP address for one of the vPC peers

Configure a different secondary IP address for one of the vPC peers

Suggested answer: C
Explanation:

Reference:

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/command/reference/vpc/n5k-vpc-cr/n5k-vpc_cmds_i.html#:~:text=a%20port%20profile.-,ip%20arp%20synchronize,no%20form%20of%20this%20command.

asked 07/10/2024
EDDIE LIN
49 questions

Question 78

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 78 113259 10072024010022000000

Refer to the exhibit. An engineer troubleshoots an OSPF neighborship problem between Router R2 and Router R10. Which action resolves the problem?

Change area ID on Router R10

Change area ID on Router R10

Resolve unicast reply from Router R2

Resolve unicast reply from Router R2

Resolve authentication type on Router R10

Resolve authentication type on Router R10

Change router ID on Router R10

Change router ID on Router R10

Suggested answer: B
asked 07/10/2024
Anu V
37 questions

Question 79

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 79 113260 10072024010022000000

Refer to the exhibit. VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?

Reset the error packet counter

Reset the error packet counter

Configure the hello timer to match the neighbor

Configure the hello timer to match the neighbor

Configure the FSPF dead interval with a value higher than 80 seconds

Configure the FSPF dead interval with a value higher than 80 seconds

Reset the inactivity timer on switch-2

Reset the inactivity timer on switch-2

Suggested answer: B
Explanation:

Reference:

https://www.cisco.com/en/US/docs/switches/datacenter/nexus5500/sw/troubleshooting/guide/n5500_ts_sans.html

asked 07/10/2024
Leon Chukwuma
35 questions

Question 80

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 80 113261 10072024010022000000

Refer to the exhibit. A network engineer configures an authentication domain through an LDAP provider on the Cisco UCS Manager for users from different companies to log into their respective organizations created in the UCS Manager.

The engineer tests the configuration and notices that any user has login access to any organization in the UCS Manager. Which action should be taken to resolve the issue?

Configure the Filter field with sAMAccountName=$company

Configure the Filter field with sAMAccountName=$company

Configure the Attribute field with the company

Configure the Attribute field with the company

Configure the Attribute field with sAMAccountName=$company

Configure the Attribute field with sAMAccountName=$company

Configure the Filter field with the company

Configure the Filter field with the company

Suggested answer: A
asked 07/10/2024
Prakash Varghese
41 questions
Total 166 questions
Go to page: of 17
Search

Related questions