AN engineer is implementing a route map to support redistribution within BGP. The route map must configured to permit all unmatched routes. Which action must the engineer perform to complete this task?

Include a permit statement as the last entry

Include a permit statement as the first entry

Include at least one explicit deny statement

Include a permit statement as the last entry

Refer to the exhibit. A network operator is attempting to configure an IS-IS adjacency between two routers, but the adjacency cannot be established. To troubleshoot the problem, the operator collects this debugging output. Which interfaces are misconfigured on these routers?

The R2 interface is configured as point-to-point, and the peer router interface is configured as multipoint.

The peer router interface is configured as Level 1 only, and the R2 interface is configured as Level 2 only

The R2 interface is configured as Level 1 only, and the Peer router interface is configured as Level 2 only

The R2 interface is configured as point-to-point, and the peer router interface is configured as multipoint.

The peer router interface is configured as point-as-point, and the R2 interface is configured as multipoint.

AN engineer is implementing MPLS OAM to monitor traffic within the MPLS domain. Which action must the engineer perform to prevent from being forwarded beyond the service provider domain when the LSP is down?

Disable IP redirects on all ingress interfaces

Disable IP redirects only on outbound interfaces

Implement the destination address for the LSP echo request packet in the 127.x.y.z/8 network

Disable IP redirects on all ingress interfaces

Configure a private IP address as the destination address of the headend router of Cisco MPLS TE.

An engineer is implementing a Cisco MPLS TE tunnel to improve the streaming experience for the clients of a video-on-demand server. Which action must the engineer perform to configure extended discovery to support the MPLS LDP session between the headend and tailend routers?

Configure a Cisco MPLS TE tunnel on both ends of the session

Configure the interface bandwidth to handle TCP and UDP traffic between the LDP peers

Configure a Cisco MPLS TE tunnel on both ends of the session

Configure an access list on the interface to permit TCP and UDP traffic

Configure a targeted neighbor session.

What occurs when a high bandwidth multicast stream is sent over an MVPN using Cisco hardware?

A data MDT is created to allow for the best transmission through the core for (S, G) multicast route entries.

The traffic uses the default MDT to transmit the data only if it isa (S,G) multicast route entry

A data MDT is created to if it is a (*, G) multicast route entries

A data and default MDT are created to flood the multicast stream out of all PIM-SM neighbors.

A data MDT is created to allow for the best transmission through the core for (S, G) multicast route entries.

Which network devices secure API platform?

next-generation intrusion detection systems

Layer 3 transit network devices

Refer to the exhibit. What is required to configure a second export destination for IP address 192.168.10.1?

Configure a version 5 flow-export to the same destination.

Refer to the exhibit. A company requires that all wireless users authenticate using dynamic key generation. Which configuration must be applied?

AP(config-if-ssid)# authentication open eap eap_methods

AP(config-if-ssid)# authentication open wep wep_methods

AP(config-if-ssid)# authentication dynamic wep wep_methods

AP(config-if-ssid)# authentication dynamic open wep_dynamic

AP(config-if-ssid)# authentication open eap eap_methods

Which OSPF networks types are compatible and allow communication through the two peering devices?

point-to-multipoint to nonbroadcast

point-to-multipoint to broadcast

Refer to the exhibit. An engineer must configure a SPAN session. What is the effect of the configuration?

Traffic received on VLANs 10, 11, and 12 is copied and sent to Interface g0/1.

Traffic sent on VLANs 10, 11, and 12 is copied and sent to interface g0/1.

Traffic sent on VLANs 10 and 12 only is copied and sent to interface g0/1.

Traffic received on VLANs 10, 11, and 12 is copied and sent to Interface g0/1.

Traffic received on VLANs 10 and 12 only is copied and sent to interface g0/1.

An engineer is configuring a GRE tunnel interface in the default mode. The engineer has assigned an IPv4 address on the tunnel and sourced the tunnel from an Ethernet interface. Which option also is required on the tunnel interface before it is operational?

(config-if)#tunnel destination <ip address>

(config-if)#keepalive <seconds retries>

(config-if)#ip tcp adjust-mss <value>

What Is a Type 2 hypervisor?

installed as an application on an already installed operating system

runs directly on a physical server and includes its own operating system

supports over-allocation of physical resources

also referred to as a "bare metal hypervisor" because it sits directly on the physical server

Refer to the exhibit. Cisco DNA Center has obtained the username of the client and the multiple devices that the client is using on the network. How is Cisco DNA Center getting these context details?

The administrator had to assign the username to the IP address manually in the user database tool on Cisco DNA Center.

Those details are provided to Cisco DNA Center by the Identity Services Engine

Cisco DNA Center pulled those details directly from the edge node where the user connected.

User entered those details in the Assurance app available on iOS and Android devices

Refer to the exhibit. After running the code in the exhibit. Which step reduces the amount of data that NETCONF server returns to the NETCONF client, to only the interface's configuration?

Use the JSON library to parse the data returned by the NETCONF server for the interface's configuration

Create an XML filter as a string and pass it to get_config() method as an argument

Use the txml library to parse the data returned by the NETCONF server for the interface's configuration

Create a JSON filter as a string and pass it to the get_config() method as an argument

Use the JSON library to parse the data returned by the NETCONF server for the interface's configuration

What is the role of the RP in PIM sparse mode?

The RP is the multicast that is the root of the PIM-SM shared multicast distribution tree.

The RP responds to the PIM join messages with the source of requested multicast group

The RP maintains default aging timeouts for all multicast streams requested by the receivers.

The RP acts as a control-plane node and does not receive or forward multicast packets.

The RP is the multicast that is the root of the PIM-SM shared multicast distribution tree.

Which two actions, when applied in the LAN network segment, will facilitate Layer 3 CAPWAP discovery for lightweight AP? (Choose two.)

Enable port security on the switch port

Configure WLC IP address on LAN switch.

Configure an ip helper-address on the router interface

Enable port security on the switch port

Why is an AP joining a different WLC than the one specified through option 43?

The API is joining a primed WLC

The WLC is running a different software version.

The API is joining a primed WLC

The AP multicast traffic unable to reach the WLC through Layer 3.

The APs broadcast traffic is unable to reach the WLC through Layer 2.

What is a characteristic of Cisco DNA Northbound APIs?

They simplify the management of network infrastructure devices.

They enable automation of network infrastructure based on intent.

They utilize multivendor support APIs.

Refer to the exhibit. All switches are configured with the default port priority value. Which two commands ensure that traffic from PC1 is forwarded over Gi1/3 trunk port between DWS1 and DSW2? (Choose two)

DSW2(config-if)#spanning-tree port-priority 16

DSW1(config-if)#spanning-tree port-priority 0

DSW2(config-if)#spanning-tree port-priority 128

Which function does a fabric edge node perform in an SD-Access deployment?

Connects endpoints to the fabric and forwards their traffic

Connects the SD-Access fabric to another fabric or external Layer 3 networks

Connects endpoints to the fabric and forwards their traffic

Provides reachability border nodes in the fabric underlay

Encapsulates end-user data traffic into LISP.

What is the structure of a JSON web token?

three parts separated by dots: header payload, and signature

three parts separated by dots: version header and signature

Cisco 350-401 Practice Test 6 - Free Online Exam Prep & Questions

An engineer is configuring a new SSID to present users with a splash page for authentication. Which WLAN Layer 3 setting must be configured to provide this functionally?

Become a Premium Member for full access

Unlock Premium Member

Cisco 350-401 Practice Test 6

Question

Cisco 350-401 Practice Tests

Practice Tests