Refer to the exhibit. What step resolves the authentication issue?

target 192 168 100 82 in the URI

What is required for a virtual machine to run?

a hypervisor and physical server hardware

a Type 1 hypervisor and a host operating system

a hypervisor and physical server hardware

What is required for intercontroller Layer 3 roaming?

WLCs have the same IP addresses configured on their interfaces.

Mobility groups are established between wireless controllers.

The management VLAN is present as a dynamic VLAN on the second WLC.

WLCs use separate DHCP servers.

WLCs have the same IP addresses configured on their interfaces.

An engineer configures GigabitEthernet 0/1 for VRRP group 115. The router must assume the primary role when it has the highest priority in the group. Which command set is required to complete this task?interface GigabitEthernet0/1 ip address 10.10.10.2 255.255.255.0 vrrp 115 ip 10.10.10.1 vrrp 115 authentication 407441579

Router(config-if)# vrrp 115 priority 100

Router(config if)# vrrp 115 track 1 decrement 100 Router(config-if)# vrrp 115 preempt

Router(config-if)# vrrp 115 priority 100

Router(config-if)# vrrp 115 track 1 decrement 10 Router(config-if)# vrrp 115 preempt

Router(config-if)# standby 115 priority 100 Router(config-if)# standby 115 preempt

What is a benefit of Type 1 hypervisors?

Network engineers are able to create virtual networks o interconnect virtual machines in Layer 2 topologies

Administrators are able to load portable virtual machine packages in OVA or QCOW2 formats.

Network engineers are able to create virtual networks o interconnect virtual machines in Layer 2 topologies

Operators are able to leverage orchestrators to manage workloads that run on multiple Type 1 hypervisors

Storage engineers are able to leverage VMDK files to provide storage to virtual machine.

What is the wireless received signal strength indicator?

The value of how strong a tireless signal is receded, measured in dBm

The value given to the strength of the wireless signal received compared to the noise level

The value of how strong the wireless signal Is leaving the antenna using transmit power, cable loss, and antenna gain

The value of how much wireless signal is lost over a defined amount of distance

The value of how strong a tireless signal is receded, measured in dBm

Refer to the exhibit. After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2.09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/0, putting Gi0/0 in err-disable state09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/1, putting Gi0/1 in err-disable stateBased on the output from SW1 and the log message received on Switch SW2, what action should the engineer take to resolve this issue?

Configure the same protocol on the EtherChannel on switch SW1 and SW2.

Connect the configuration error on interface Gi0/1 on switch SW1.

Define the correct port members on the EtherChannel on switch SW1.

Correct the configuration error on interface Gi0/0 switch SW1.

Refer to the exhibit. An engineer is troubleshooting an application running on Apple phones. The application Is receiving incorrect QoS markings. The systems administrator confirmed that ail configuration profiles are correct on the Apple devices. Which change on the WLC optimizes QoS for these devices?

Change the QoS level to Platinum

How does Cisco Trustsec enable more flexible access controls for dynamic networking environments and data centers?

classifies traffic based an the contextual identity of the endpoint rather than its IP address

classifies traffic based on advanced application recognition

What is the responsibility of a secondary WLC?

It registers the LAPs if the primary controller fails.

It shares the traffic load of the LAPs with the primary controller.

It avoids congestion on the primary controller by sharing the registration load on the LAPs.

It registers the LAPs if the primary controller fails.

It enables Layer 2 and Layer 3 roaming between Itself and the primary controller.

Refer to the exhibit. On which interfaces should VRRP commands be applied to provide first hop redundancy to PC-01 and PC-02?

G0/1on Edge-01 and G0/1 on Edge-02

G0/0 on Edge-01 and G0/0 on Edge-02

G0/1on Edge-01 and G0/1 on Edge-02

Refer to the exhibit. Which result does the python code achieve?

The code converts time to the "year/month/day" time format.

The code encrypts a base64 decrypted password.

The code converts time to the "year/month/day" time format.

The code converts time to the yyyymmdd representation.

The code converts time to the Epoch LINUX time format.

Refer to the exhibit. A network architect has partially configured static NAT. which commands should be asked to complete the configuration?

R1(config)#interface GigabitEthernet0/0 R1(config)#ip nat outsideR1(config)#interface GigabitEthernet0/1 R1(config)#ip nat inside

R1(config)#interface GigabitEthernet0/0 R1(config)#ip pat outsideR1(config)#interface GigabitEthernet0/1 R1(config)#ip pat inside

R1(config)#interface GigabitEthernet0/0 R1(config)#ip nat outsideR1(config)#interface GigabitEthernet0/1 R1(config)#ip nat inside

R1(config)#interface GigabitEthernet0/0 R1(config)#ip nat insideR1(config)#interface GigabitEthernet0/1 R1(config)#ip nat outside

R1(config)#interface GigabitEthernet0/0 R1(config)#ip pat insideR1(config)#interface GigabitEthernet0/1 R1(config)#ip pat outside

How does the EIGRP metric differ from the OSPF metric?

The EIGRP metric Is calculated based on bandwidth and delay. The OSPF metric is calculated on bandwidth only.

The EIGRP metric is calculated based on bandwidth only. The OSPF metric is calculated on delay only.

The EIGRP metric is calculated based on delay only. The OSPF metric is calculated on bandwidth and delay.

The EIGRP metric Is calculated based on bandwidth and delay. The OSPF metric is calculated on bandwidth only.

The EIGRP metric Is calculated based on hop count and bandwidth. The OSPF metric is calculated on bandwidth and delay.

What is the difference between a RIB and a FIB?

The FIB is populated based on RIB content

The RIB is used to make IP source prefix-based switching decisions

The FIB is where all IP routing information is stored

The RIB maintains a mirror image of the FIB

The FIB is populated based on RIB content

An engineer must create an EEM applet that sends a syslog message in the event a change happens in the network due to trouble with an OSPF process. Which action should the engineer use?

action 1 syslog pattern "OSPF ROUTING ERROR"

action 1 syslog msg "OSPF ROUTING ERROR"

action 1 syslog send "OSPF ROUTING ERROR"

action 1 syslog pattern "OSPF ROUTING ERROR"

action 1syslog write "OSPF ROUTING ERROR"

What do Cisco DNA southbound APIs provide?

Interface between the controller and the network devices

NETCONF API interface for orchestration communication

RESful API interface for orchestrator communication

Interface between the controller and the consumer

What does the LAP send when multiple WLCs respond to the CISCO_CAPWAPCONTROLLER. localdomain hostname during the CAPWAP discovery and join process?

Unicast discovery request to the first WLS that resolves the domain name

unicast discovery request to each WLC

Unicast discovery request to the first WLS that resolves the domain name

What is a VPN in a Cisco SD-WAN deployment?

virtualized environment that provides traffic isolation and segmentation in the SD-WAN fabric

common exchange point between two different services

attribute to identify a set of services offered in specific places in the SD-WAN fabric

virtualized environment that provides traffic isolation and segmentation in the SD-WAN fabric

virtual channel used to carry control plane information

Which outcome is achieved with this Python code?

connects to a Cisco device using SSH and exports the BGP table for the prefix

connects to a Cisco device using SSH and exports the routing table information

displays the output of the show command in a formatted way

connects to a Cisco device using SSH and exports the BGP table for the prefix

connects to a Cisco device using Telnet and exports the routing table information

What is provided by the Stealthwatch component of the Cisco Cyber Threat Defense solution?

real-time awareness of users, devices and traffic on the network

real-time threat management to stop DDoS attacks to the core and access networks

real-time awareness of users, devices and traffic on the network

dynamic threat control for web traffic

Refer to the exhibit. An engineer must establish eBGP peering between router R3 and router R4. Both routers should use their loopback interfaces as the BGP router ID. Which configuration set accomplishes this task?

R3(config)#router bgp 200R3(config-router)#neighbor 10.24.24.4 remote-as 100R3(config-router)#bgp router-id 10.3.3.3R4(config)#router bgp 100R4(config-router)#neighbor 10.24.24.3 remote-as 200R4(config-router)#bgp router-id 10.4.4.4

R3(config)#router bgp 200R3(config-router)#neighbor 10.4.4.4 remote-as 100R3(config-router)# neighbor 10.4.4.4 update-source Loopback0R4(config)#router bgp 100R4(config-router)#neighbor 10.3.3.3 remote-as 200R4(config-router)#network 10.3.3.3 update-source Loopback0

R3(config)#router bgp 200R3(config-router)#neighbor 10.24.24.4 remote-as 100R3(config-router)#neighbor 10.24.24.4 update-source Loopback0R4(config)#router bgp 100R4(config-router)#neighbor 10.24.24.3 remote-as 200R4(config-router)#neighbor 10.24.24.3 update-source Loopback0

R3(config)#router bgp 200R3(config-router)#neighbor 10.4.4.4 remote-as 100R3(config-router)#bgp router-id 10.3.3.3R4(config)#router bgp 100R4(config-router)#neighbor 10.3.3.3 remote-as 200R4(config-router)#bgp router-id 10.4.4.4

R3(config)#router bgp 200R3(config-router)#neighbor 10.24.24.4 remote-as 100R3(config-router)#bgp router-id 10.3.3.3R4(config)#router bgp 100R4(config-router)#neighbor 10.24.24.3 remote-as 200R4(config-router)#bgp router-id 10.4.4.4

Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?

security group tag number assigned to each port on a network

security group tag ACL assigned to each port on a switch

security group tag number assigned to each port on a network

security group tag number assigned to each user on a switch

security group tag ACL assigned to each router on a network

In a three-tier hierarchical campus network design, which action is a design best-practice for the core layer?

provide redundant Layer 3 point-to-point links between the core devices for more predictable and faster convergence

provide QoS prioritization services such as marking, queueing, and classification for critical network traffic

provide redundant Layer 3 point-to-point links between the core devices for more predictable and faster convergence

provide advanced network security features such as 802. IX, DHCP snooping, VACLs, and port security

provide redundant aggregation for access layer devices and first-hop redundancy protocols such as VRRP

Refer to the Exhibit. An engineer is installing a new pair of routers in a redundant configuration. When checking on the standby status of each router the engineer notices that the routers are not functioning as expected.Which action will resolve the configuration error?

configure matching hold and delay timers

configure matching priority values

configure unique virtual IP addresses

Cisco 350-401 Practice Test 7 - Free Online Exam Prep & Questions

An engineer must protect their company against ransom ware attacks. Which solution allows the engineer to block the execution stage and prevent file encryption?

Become a Premium Member for full access

Unlock Premium Member

Cisco 350-401 Practice Test 7

Question

Cisco 350-401 Practice Tests

Practice Tests