Refer to the exhibit. An engineer configures the BGP adjacency between R1 and R2, however, it fails to establish Which action resolves the issue?

Change the remote-as number on R1 to 6500.

Change the network statement on R1 to 172.16 10.0

Change the remote-as number for 192 168.100.11.

Enable synchronization on R1 and R2

Change the remote-as number on R1 to 6500.

Refer to the exhibit. The network administrator must be able to perform configuration changes when all the RADIUS servers are unreachable. Which configuration allows all commands to be authorized if the user has successfully authenticated?

aaa authorization exec default group radius if-authenticated

aaa authorization exec default group radius none

aaa authentication login default group radius local none

aaa authorization exec default group radius if-authenticated

aaa authorization exec default group radius

What is a characteristic of Cisco StackWise technology?

lt combines exactly two devices

It supports devices that are geographically separated

lt combines exactly two devices

It is supported on the Cisco 4500 series.

Why would an engineer use YANG?

to transport data between a controller and a network device

to translate JSON into an equivalent XML syntax

What is the function of a control-plane node In a Cisco SD-Access solution?

to run a mapping system that manages endpoint to network device relationships

to implement policies and communicate with networks outside the fabric

to connect external Layer 3 networks to the SD-Access fabric

to connect APs and wireless endpoints to the SD-Access fabric

Refer to the exhibit. What are two reasons for IP SLA tracking failure? (Choose two )

A route back to the R1 LAN network is missing in R2.

The destination must be 172 30 30 2 for icmp-echo

A route back to the R1 LAN network is missing in R2.

The source-interface is configured incorrectly.

The default route has the wrong next hop IP address

A customer wants to use a single SSID to authenticate loT devices using different passwords. Which Layer 2 security type must be configured in conjunction with Cisco ISE to achieve this requirement?

Cisco Centralized Key Management

Refer to the exhibit. An engineer must prevent the R6 loopback from getting into Area 2 and Area 3 from Area 0 Which action must the engineer take?

Apply a filter list outbound on R3 and R7

Apply a fitter list inbound on R2 and R9

Apply a filter list outbound on R3 and R7

Apply a filter list outbound on R7 only.

Apply a filter list inbound on R3 and R7

Refer to the exhibit. Which two facts does the device output confirm? (Choose two.)

The standby device is configured with the default HSRP priority.

The device is using the default HSRP hello timer

The device sends unicast messages to its peers

The device's HSRP group uses the virtual IP address 10.0.3.242

The standby device is configured with the default HSRP priority.

The device is using the default HSRP hello timer

The device is configured with the default HSRP priority

How is a data modeling language used?

To enable data lo be easily structured, grouped, validated, and replicated

To represent finite and well-defined network elements that cannot be changed

To model the flows of unstructured data within the infrastructure

To provide human readability to scripting languages

Refer to the exhibit. Which command must be applied to Router 1 to bring the GRE tunnel to an up/up state?

Router1(config-if)&tunnel source Loopback0

Routed (config if funnel mode gre multipoint

Router1(config-if)&tunnel source Loopback0

Router1(config-if)#tunnel source GigabitEthernet0/1

Router1 (config)#interface tunnel0

Which method is used by an AP to join HA controllers and is configured in NVRAM?

Primary/Secondary/Tertiary/Backup

Refer to the exhibit. A network engineer is enabling logging to a local buffer, to the terminal and to a syslog server for all debugging level logs filtered by facility code 7. Which command is needed to complete this configuration snippet?

logging discriminator Disc1 severity includes 7 facility includes fac7

logging discriminator Disc1 severity includes 7

logging buffered discriminator Disc1 debugging

logging discriminator Disc1 severity includes 7 facility includes fac7

How can an engineer prevent basic replay attacks from people who try to brute force a system via REST API?

Add a timestamp to the request In the API header.

Add OAuth to the request in the API header.

When is the Design workflow used In Cisco DNA Center?

in a greenfield deployment, with no existing infrastructure

in a greenfield or brownfield deployment, to wipe out existing data

in a brownfield deployment, to modify configuration of existing devices in the network

in a brownfield deployment, to provision and onboard new network devices

Refer to the exhibit. An engineer attempts to establish BGP peering between router CORP and two ISP routers. What is the root cause for the failure between CORP and ISP#2?

There is a password mismatch between router CORP and router ISP#2.

Router ISP#2 is configured to use SHA-1 authentication.

There is a password mismatch between router CORP and router ISP#2.

Router CORP is configured with an extended access control list.

MD5 authorization is configured incorrectly on router ISP#2.

In which two ways does TCAM differ from CAM? (Choose two.)

CAM Is used by routers for IP address lookups, and TCAM is used to make Layer 2 forwarding decisions.

The MAC address table Is contained in TCAM, and ACL and QoS information is stored in CAM.

CAM is used to make Layer 2 forwarding decisions, and TCAM is used for Layer 3 address lookups.

The MAC address table is contained in CAM, and ACL and QoS Information Is stored in TCAM.

CAM Is used by routers for IP address lookups, and TCAM is used to make Layer 2 forwarding decisions.

CAM is used for software switching mechanisms, and TCAM Is used for hardware switching mechanisms.

The MAC address table Is contained in TCAM, and ACL and QoS information is stored in CAM.

What are two benefits of implementing a Cisco SD-WAN architecture? (Choose two)

It allows configuration of application-aware policies with real time enforcement.

It simplifies endpoint provisioning through standalone router management

It provides resilient and effective traffic flow using MPLS.

It improves endpoint protection by integrating embedded and cloud security features.

It allows configuration of application-aware policies with real time enforcement.

It simplifies endpoint provisioning through standalone router management

It enforces a single. scalable. hub-and-spoke topology.

How does CEF switching differ from process switching on Cisco devices?

CEF switching uses adjacency tables built by the CDP protocol, and process switching uses the routing table

CEF switching saves memory by sorting adjacency tables in dedicate memory on the line cards, and process switching stores all tables in the main memory

CEF switching uses adjacency tables built by the CDP protocol, and process switching uses the routing table

CEF switching uses dedicated hardware processors, and process switching uses the main processor

CEF switching uses proprietary protocol based on IS-IS for MAC address lookup, and process switching uses in MAC address table

A customer wants to provide wireless access to contractors using a guest portal on Cisco ISE. The portal Is also used by employees A solution is implemented, but contractors receive a certificate error when they attempt to access the portalEmployees can access the portal without any errors.Which change must be implemented to allow the contractors and employees to access the portal?

Install an internal CA signed certificate on the Cisco ISE

Install a trusted third-party certificate on the Cisco ISE.

Install an Internal CA signed certificate on the contractor devices

Install an internal CA signed certificate on the Cisco ISE

install a trusted third-party certificate on the contractor devices.

How must network management traffic be treated when defining QoS policies?

as delay-sensitive traffic in a low latency queue

using minimal bandwidth guarantee

using the same marking as IP routing

What is one difference between EIGRP and OSPF?

EIGRP uses the DUAL distance vector algorithm, and OSPF uses the Dijkstra link-state algorithm

OSPF is a Cisco proprietary protocol, and EIGRP is an IETF open standard protocol.

OSPF uses the DUAL distance vector algorithm, and EIGRP uses the Dijkstra link-state algorithm

EIGRP uses the variance command lot unequal cost load balancing, and OSPF supports unequal cost balancing by default.

EIGRP uses the DUAL distance vector algorithm, and OSPF uses the Dijkstra link-state algorithm

Why would a log file contain a * next to the date?

The network device was unable to reach The NTP server when the log messages were recorded

The network device was receiving NTP time when the log messages were recorded.

The network device was unable to reach The NTP server when the log messages were recorded

The network device is not configured to use NTP.

The network device is nor configured to use NTP time stamps for logging

Which action is performed by Link Management Protocol in a Cisco StackWise Virtual domain?

It rejects any unidirectional link traffic forwarding

It determines if the hardware is compatible to form the StackWise Virtual domain

discovers the StackWise domain and brings up SVL interfaces.

It determines which switch becomes active or standby

A customer transitions a wired environment to a Cisco SD-Access solution. The customer does not want to integrate the wireless network with the fabric. Which wireless deployment approach enables the two systems to coexist and meets the customer requirement?

Deploy the wireless network over the top of the fabric

Deploy the APs in autonomous mode

Deploy the wireless network over the top of the fabric

Deploy a separate network for the wireless environment

Implement a Cisco DNA Center to manage the two networks

Cisco 350-401 Practice Test 9 - Free Online Exam Prep & Questions

Question 1 / 40

What does a northbound API accomplish?

programmatic control of abstracted network resources through a centralized controller

access to controlled network resources from a centralized node

communication between SDN controllers and physical switches

controlled access to switches from automated security applications

Comment (0)

Cisco 350-401 Practice Test 9

Question

Cisco 350-401 Practice Tests

Practice Tests