ExamGecko
Login
Home / Cisco / 300-615 / List of questions
Ask Question

Cisco 300-615 Practice Test - Questions Answers, Page 3

Add to Whishlist

List of questions

Question 21

Report Export Collapse


An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails.

The engineer can ping Cisco UCS Central from UCS Manager. Which two actions must the engineer attempt to resolve the problem? (Choose two.)

Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.

Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.

Apply the UCS Central license to UCS Central.

Apply the UCS Central license to UCS Central.

Place Cisco UCS Manager on the same subnet as Cisco UCS Central.

Place Cisco UCS Manager on the same subnet as Cisco UCS Central.

Allow port 443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Suggested answer: A, D
asked 07/10/2024
Johny Nguyen
38 questions

Question 22

Report Export Collapse

You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1

CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.

The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.

Rebooting the APICs and the leaf and spine switches after wiping them is not required.

Rebooting the APICs and the leaf and spine switches after wiping them is not required.

You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.

You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.

The same Fabric Name value should be used before after wiping all devices.

The same Fabric Name value should be used before after wiping all devices.

Suggested answer: C
asked 07/10/2024
Christian Andrew TANAP
53 questions

Question 23

Report Export Collapse

An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a “resolve slot” warning. Which server maintenance action resolves the issue?

Perform diagnostic interrupt on the server.

Perform diagnostic interrupt on the server.

Re-acknowlegement the server.

Re-acknowlegement the server.

Reset the server.

Reset the server.

Decomission the server.

Decomission the server.

Suggested answer: B
asked 07/10/2024
Tyler Raymond
46 questions

Question 24

Report Export Collapse

Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?

Modify the VLAN assignment to vNICs.

Modify the VLAN assignment to vNICs.

Change the PIN groups on the vHBAs.

Change the PIN groups on the vHBAs.

Modify the FCoE VLAN.

Modify the FCoE VLAN.

Set the FCoE VLAN as the native VLAN on server uplinks.

Set the FCoE VLAN as the native VLAN on server uplinks.

Suggested answer: C
asked 07/10/2024
Cynan Jones
43 questions

Question 25

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 25 113206 10072024010022000000

An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?

The interface is working correctly and fully operational, but it is not in use.

The interface is working correctly and fully operational, but it is not in use.

The interface policy is misconfigured.

The interface policy is misconfigured.

“out-of-service” is the default interface status in ACI.

“out-of-service” is the default interface status in ACI.

“out-of-service” indicates that no service graph is in use for this interface.

“out-of-service” indicates that no service graph is in use for this interface.

Suggested answer: B
asked 07/10/2024
Fermin Paneque Cabrera
44 questions

Question 26

Report Export Collapse

A user reports that they cannot reach from a UCS server to an FC Storage array. Which command is used to test communication between an FCF and a target?

fcroute

fcroute

traceroute

traceroute

fcping

fcping

ping

ping

Suggested answer: C
asked 07/10/2024
Dereque Datson
47 questions

Question 27

Report Export Collapse

An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

M-Series module

M-Series module

ESSENTIALS license

ESSENTIALS license

STORAGE-ENT license

STORAGE-ENT license

FCoE license

FCoE license

F-Series module

F-Series module

Suggested answer: D, E
asked 07/10/2024
Diogo Vitor
44 questions

Question 28

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 28 113209 10072024010022000000

An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

Configure the role name to match the group name on Microsoft Active Directory.

Configure the role name to match the group name on Microsoft Active Directory.

Include specific users into MDS role configuration.

Include specific users into MDS role configuration.

Configure SSH logins on Cisco MDS switch.

Configure SSH logins on Cisco MDS switch.

Integrate Cisco MDS with Microsoft Active Directory.

Integrate Cisco MDS with Microsoft Active Directory.

Suggested answer: A
asked 07/10/2024
Bill May
52 questions

Question 29

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 29 113210 10072024010022000000

An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?

Add the FCoE VLAN to the allowed VLAN list.

Add the FCoE VLAN to the allowed VLAN list.

Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.

Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.

Configure the interface as a trunk port.

Configure the interface as a trunk port.

Configure the interface to use the native VLAN of the trunk port.

Configure the interface to use the native VLAN of the trunk port.

Suggested answer: C
asked 07/10/2024
nebaba monda
53 questions

Question 30

Report Export Collapse

Refer to the exhibit.

Cisco 300-615 image Question 30 113211 10072024010022000000

A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch.

The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?

Replace the SFP port module in fc2/10.

Replace the SFP port module in fc2/10.

Configure the admin port type E on the upstream switch that connects the port.

Configure the admin port type E on the upstream switch that connects the port.

Enable NPIV on the upstream switch that connects the port.

Enable NPIV on the upstream switch that connects the port.

Configure the BB_credit buffers on the upstream switch that connects the port.

Configure the BB_credit buffers on the upstream switch that connects the port.

Suggested answer: C
asked 07/10/2024
Faqeer Ali
44 questions
Total 166 questions
Go to page: of 17
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

DRAG DROP Drag each item listed on the left to its proper category on the right Not all items will fit the categories.
An engineer is implementing a new BGP peering in their new data center. The engineer set up the BGP session that peers with the remote end. As soon as the BGP peers attempt to exchange routing prefixes, one of the BGP peers drops the connection. After reviewing the configuration, the engineer reviews the logging messages. The engineer discovers that the router is missing keepalives from the remote end and terminates the session. Which action resolves the issue?
Refer to the exhibit. Refer to the exhibit. A functioning trunk port Ethernet1/48 exists between two identical Cisco Nexus 5000 Series Switches. The interfaces on the switches support the MACsec feature and are configured identically. To enable manual MACsec, an engineer adds the configuration shown in the exhibit to both sides of the trunk. The trunk port stops functioning. Which action should be taken to resolve the issue?
A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?
Refer to the exhibit. A client configures an upgrade of its Cisco Nexus switches that are connected to the Cisco ACI controller, such that the switches are upgraded one at a time. After the upgrade is run, it is discovered that both Cisco Nexus switches were upgraded simultaneously. Which two actions ensure that the switches upgrade one at a time? (Choose two.)
A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue? A. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels 2) Verify that at least two physical cables between the IOM and fabric interconnect function properly. 3) Check for runtime link down status 4) Reseat the affected IOM.
Refer to the exhibit. The FCoE traffic fails to traverse the vfc2 interface. The VSAN 102 is configured for vfc2. Which action resolves the issue?
Refer to the exhibit. Refer to the exhibit. The monitoring team reports an inability to access the devices after a new centralized management integration. Which action resolves the issue?
When the engineer runs the command, this error is received: opsengineer@wkst1:/home/auto/bash_scripts$ curl –s –b cookie_file_39422186.txt –X GET –k 192.15.132.101/api/node/class/Tenant.json {“totalCount”:”1”,”imdata”:[{“error”:{“attributes”:{“code”:”400”,”text”:”Request failed, (output omitted)”}}}]} Which action resolves the issue?
Refer to the exhibit. An administrator directly connects a Fibre Channel storage array to ports 1 through 4 on a Cisco UCS 6454 Fabric Interconnect. The administrator configures a service profile to boot directly from the new Fibre Channel storage array, but the service profile fails to boot. When the administrator checks the output of the show flogi database command on the fabric interconnect, it shows the output presented in the exhibit. Which action resolves the issue?