Cisco 350-501 Practice Test - Questions Answers, Page 21
Question list
List of questions
Related questions
A network engineer Is implementing a QoS policy for outbound management traffic classification and marking on a CPE device with these requirements:
• Management protocols must be marked with DSCP AF class 2 w4h low drop probability.
• Monitoring protocols must be marked with DSCP AF class 1 with low drop probability.
• All remaining traffic must be marked with a DSCP value of 0.
Which configuration must the engineer implement to satisfy the requirements?
Refer To the exhibit.
Which BGP attribute should be manipulated to have CE1 use PE1 as the primary path to the Internet?
The weight attribute should be manipulated on PE1 on outbound routes advertised to CE1.
The MED should be manipulated on CE1 on inbound routes from PE1.
The local preference attribute should be manipulated on PE2 on inbound routes advertised to CE1.
The origin of all routes should be modified on each router on inbound and outbound routes advertised to CE1.
Refer to the exhibit.
The network engineer who manages ASN 65010 is provisioning a customer VRF named CUSTOMERABC on PE-2. The PE-CE routing protocol is OSPF Internet reachability is available via the OSPF 0 0 0.0/0 route advertised by CE-1 to PE-1 In the customer VRF Which configuration must the network engineer Implement on PE-2 so that CE-2 has connectivity to the Internet?
Refer to the exhibit.
A network operator working for a telecommunication company with an employee 3994:37:650 is implementing a cisco Unified MPLS solution. What is the effect of this implementation?
EIGRP is deployed between the PEs and ABRs with RFC 3107.
OSPF is deployed between the PEs and ABRs with RFC 3107.
IS-IS is deployed between the PEs and ABRs with RFC 3107.
BGP is deployed between the PEs and ABRs with RFC 3107.
A network engineer must implement SNMPv2 with these parameters
Enable SNMP community string C1sc0 with read-only permissions.
Enable interface index persistence.
Restrict the SNMP community to only the monitoring server with IP address 198.18 19 100/32.
Provide view-only access to ospflfEntry and ospfNbrEntry.
Which configuration must the engineer apply?
Option A
Option B
Option C
Option D
An engineer must extend Layer 2 Between two campus sites connected through an MPLS backbone that encapsulates Layer 2 and Layer 3 data Which action must the engineer perform on the routers to accomplish this task?
Configure a EtherChannel for E-LAN.
Configure a pseudowire for E-LINE.
Configure Cisco MPLS TE for use with E-TREE.
Configure QoS for MPLS and E-ACCESS
The engineering team at a large ISP has been alerted a customer network is experiencing high traffic congestion. After a discussion between the ISP and technical personnel at the customer site, the team agrees that traffic to the customer network that exceeds a specific threshold will be dropped.
Which task must the engineer perform on the network to implement traffic policing changes?
Configure RSVP to reserve bandwidth on all interfaces when a path is congested.
Enable Cisco Discovery Protocol on the interface sending the packets.
Enable Cisco Express Forwarding on the interfaces sending and receiving the packets.
Set IP precedence values to take effect when traffic exceeds a given threshold.
An engineer is implementing IGMP with SSM on a multicampus network that supports video streaming. Which task must the engineer perform as part of the process?
Configure the network to use IGMPv3.
Configure the network to use bidirectional PIM.
Configure an RP that uses static assignments only.
Configure the network to use the PIM bsr-candidate
Refer to the exhibit.
An engineer has started to configure a router for OSPF, as shown Which configuration must an engineer apply on the network so that area 15 traffic from R5 to R1 will prefer the route through R4?
Place the link between R3 and R5 in a stub area to force traffic to use the route through R4.
Increase the cost on the link between R2 and R4, to influence the path over R3 and R4.
Implement a multiarea adjacency on the link between R2 and R4, with the cost manipulated to make the path through R4 preferred.
Implement a sham link on the between R3 and R2 to extend area 0 area 15.
Refer to the exhibit.
An engineer has started to configure a router for secure remote access as shown. All users who require network access need to be authenticated by the SSH Protocol.Which two actions must the engineer implement to complete the SSH configuration? (Choose two.)
Configure an IP domain name.
Configure service password encryption.
Configure crypto keys
Configure ACL 100 to permit access to port 22.
Configure a password under the vty lines.
Question