Home / Cisco / 350-401

Cisco 350-401 Practice Test - Questions Answers, Page 32

Question list

List of questions

Question 311

(0)

Which two parameters are examples of a QoS traffic descriptor? (Choose two)

Question 312

(0)

What are two common sources of interference for Wi-Fi networks? (Choose two.)

Question 313

(0)

Refer to the exhibit. After configuring HSRP an engineer enters the show standby command. Which two facts are derived from the output? (Choose two.)

Question 314

(0)

If a client's radio device receives a signal strength of -67 dBm and the noise floor is -85 dBm, what is the SNR value?

Question 315

(0)

Refer to the exhibit. An engineer configures OSPF and wants to verify the configuration Which configuration is applied to this device?

Question 316

(0)

A network monitoring system uses SNMP polling to record the statistics of router interfaces The SNMP queries work as expected until an engineer installs a new interface and reloads the router After

Question 317

(0)

In a Cisco SD-Access solution, which protocol is used by an extended node to connect to a single edge node?

Question 318

(0)

An engineer must enable a login authentication method that allows a user to log in by using local authentication if all other defined authentication methods fail Which configuration should be applie

Question 319

(0)

Refer to the exhibit. Which Python code snippet prints the descriptions of disabled interfaces only?

Question 320

(0)

When firewall capabilities are considered, which feature is found only in Cisco next-generation firewalls?

Related questions

What are two differences between the RIB and the FIB? (Choose two.)

Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?

An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?

An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?

Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?

An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)

Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?

Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?

Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?

A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, Client roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?

Question 311

Which two parameters are examples of a QoS traffic descriptor? (Choose two)

MPLS EXP bits

bandwidth

DSCP

ToS

packet size

Show Answer Comment (0)

Question 312

What are two common sources of interference for Wi-Fi networks? (Choose two.)

rogue AP

conventional oven

fire alarm

LED lights

radar

Show Answer Comment (0)

Question 313

Refer to the exhibit.

After configuring HSRP an engineer enters the show standby command. Which two facts are derived from the output? (Choose two.)

The router with IP 10.10 1.3 is active because it has a higher IP address

If Fa0/0 is shut down, the HSRP priority on R2 becomes 80

R2 Fa1/0 regains the primary role when the link comes back up

R2 becomes the active router after the hold time expires.

R2 is using the default HSRP hello and hold timers.

Show Answer Comment (0)

Question 314

If a client's radio device receives a signal strength of -67 dBm and the noise floor is -85 dBm, what is the SNR value?

15 dB

16 dB

18 dB

20 dB

Show Answer Comment (0)

Question 315

Refer to the exhibit.

An engineer configures OSPF and wants to verify the configuration Which configuration is applied to this device?

Show Answer Comment (0)

A network monitoring system uses SNMP polling to record the statistics of router interfaces The SNMP queries work as expected until an engineer installs a new interface and reloads the router After this action, all SNMP queries for the router fail What is the cause of this issue?

The SNMP community is configured incorrectly

The SNMP interface index changed after reboot.

The SNMP server traps are disabled for the interface index

The SNMP server traps are disabled for the link state.

Show Answer Comment (0)

Question 317

In a Cisco SD-Access solution, which protocol is used by an extended node to connect to a single edge node?

VXLAN

IS-IS

802 1Q

CTS

Show Answer Comment (0)

Question 318

An engineer must enable a login authentication method that allows a user to log in by using local authentication if all other defined authentication methods fail Which configuration should be applied?

aaa authentication login CONSOLE group radius local-case enable aaa

authentication login CONSOLE group radius local enable none

aaa authentication login CONSOLE group radius local enable

aaa authentication login CONSOLE group tacacs+ local enable

Show Answer Comment (0)