Home / Cisco / 350-401

Cisco 350-401 Practice Test - Questions Answers, Page 76

Question list

List of questions

Question 751

(0)

What is a command-line tool for consuming REST APIs?

Question 752

(0)

An engineer receives a report that an application exhibits poor performance. On the switch where the server is connected, this syslog message is visible: SW_MATM4-MACFLAP_N0HF: Host 0054.3831.8253

Question 753

(0)

DRAG DROP Drag and drop the snippets onto the blanks within the code to construct a script that brings up the failover Ethernet port if the primary port goes down and also shuts down the failover p

Question 754

(0)

Refer to the exhibit. Refer to the exhibit. An engineer must save the configuration of router R2 using the NETCONF protocol. Which script must be used?

Question 755

(0)

What is a characteristic of para-virtualization?

Question 756

(0)

When a wired client connects to an edge switch in a Cisco SD-Access fabric, which component decides whether the client has access to the network?

Question 757

(0)

Which TLV value must be added to Option 43 when DHCP is used to ensure that APs join the WLC?

Question 758

(0)

DRAG DROP Drag and drop the description of the VSS technology from the left to the right. NOT all options are used.

Question 759

(0)

What is a benefit of YANG modules?

Question 760

(0)

What is a benefit of YANG modules?

Related questions

Which option works with a DHCP server to return at least one WLAN management interface IP address during the discovery phase and is dependent upon the VCI of the AP?

What are two differences between the RIB and the FIB? (Choose two.)

An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?

An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?

Which port is required to allow APs to join a WLC when directed broadcasts are used on a Cisco iOS switch?

Refer to the Exhibit. Refer to the exhibit. Which action must be performed to allow RESTCONF access to the device?

An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)

Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?

Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?

A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points on the 5520 and 9800 WLC. After a failure on the primary 5520 WLC, all WLAN services remain functional; however, Client roam between the 5520 and 9800 controllers without dropping their connection. Which feature must be configured to remedy the issue?

Question 751

What is a command-line tool for consuming REST APIs?

Postman

CURL

Firefox

Python requests

Show Answer Comment (0)

Question 752

An engineer receives a report that an application exhibits poor performance. On the switch where the server is connected, this syslog message is visible:

SW_MATM4-MACFLAP_N0HF: Host 0054.3831.8253 in vlan 14 is flapping between port GUAM and port Gi1/0/2.

What is causing the problem?

wrong SFP+ and cable connected between the server and the switch

undesirable load-balancing configuration on the switch

failed NIC on the server

invalid port channel configuration on the switch

Show Answer Comment (0)

Drag and drop the snippets onto the blanks within the code to construct a script that brings up the failover Ethernet port if the primary port goes down and also shuts down the failover port when the primary returns to service. Not all options are used.