ExamGecko
Login
Home / Cisco / 350-401 / List of questions
Ask Question

Cisco 350-401 Practice Test - Questions Answers, Page 79

Add to Whishlist

List of questions

Question 781

Report Export Collapse

A network administrator wants to install new VoIP switches in a small network closet but is concerned about the current heat level of the room. Which of the following should the administrator take into consideration before installing the new equipment?

Become a Premium Member for full access
  Unlock Premium Member

Question 782

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 782 116081 10102024232944000000

Which action must be taken to configure a WLAN for WPA2-AES with PSK and allow only 802.l1r-capable clients to connect?

Become a Premium Member for full access
  Unlock Premium Member

Question 783

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 783 116082 10102024232944000000

Which result Is achieved by the CoPP configuration?

Become a Premium Member for full access
  Unlock Premium Member

Question 784

Report Export Collapse

Which function does a virtual switch provide?

Become a Premium Member for full access
  Unlock Premium Member

Question 785

Report Export Collapse

When a branch location loses connectivity, which Cisco FlexConnect state rejects new users but allows existing users to function normally?

Become a Premium Member for full access
  Unlock Premium Member

Question 786

Report Export Collapse

Which JSON script is properly formatted?

A)

Cisco 350-401 image Question 786 116085 10102024232944000000

B)

Cisco 350-401 image Question 786 116085 10102024232944000000

C)

Cisco 350-401 image Question 786 116085 10102024232944000000

D)

Cisco 350-401 image Question 786 116085 10102024232944000000

Become a Premium Member for full access
  Unlock Premium Member

Question 787

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 787 116086 10102024232944000000

An engineer must create a manually triggered EEM applet to enable the R2 router interface and assign an IP address to it. What is required to complete this configuration?

Become a Premium Member for full access
  Unlock Premium Member

Question 788

Report Export Collapse

How does a Type 1 hypervisor function?

Become a Premium Member for full access
  Unlock Premium Member

Question 789

Report Export Collapse

In a wireless network environment, what is calculated using the numencal values of the transmitter power level, cable loss, and antenna gain?

Become a Premium Member for full access
  Unlock Premium Member

Question 790

Report Export Collapse

Which Cisco DNA Center application is responsible for group-based access control permissions?

Become a Premium Member for full access
  Unlock Premium Member
Total 983 questions
Go to page: of 99
Open VPLUS File
Convert VPLUS to PDF

Related questions

An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)
A customer has recently implemented a new wireless infrastructure using WLC-5520 at a site directly next to a large commercial airport. Users report that they intermittently lose WI-FI connectivity, and troubleshooting reveals it is due to frequent channel changes. Which two actions fix this issue? (Choose two)
An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?
Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?
Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
What are two differences between the RIB and the FIB? (Choose two.)
Refer to the exhibit. What is the result of this Python code?
An engineer must use IP SLA to measure the network performance and record statistics hop-by-hop. Which configuration must be used?
A network engineer must configure the VTY lines on a router to achieve these results: Remote access should be permitted for all feasible protocols. Only a password should be required for device authentication. All idle EXEC sessions must be terminated in 60 minutes. Which configuration should be applied?
Which devices does Cisco DNA Center configure when deploying an IP-based access control policy?