ExamGecko
Search Search Login
Home Home / Cisco / 350-601

Cisco 350-601 Practice Test - Questions Answers, Page 8

Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit. An engineer configures FCoE in a newly installed data center. Which configuration must be applied to activate VSAN 100 on VFC100?
Refer to the exhibit. A source is sending a multicast traffic stream to the receiver. How is the multicast traffic expected to flow through the network when it reaches a vPC peer?
Refer to the exhibit. Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal? A) B) C) D)
DRAG DROP Refer to the exhibit. During a recent outage, a network engineer discovered that host A started to experience intermittent connectivity, when Leaf102 was down. Drag and drop the code snippets from the bottom onto the boxes in the code to resolve the problem. Not all code snippets are used.
Refer to the exhibit. An engineer must access a Cisco UCS C-Series server KVM from a remote location. The engineer must use the out-of-band interface to access the KYM. Which configuration set meets these requirements?
Refer to the exhibit. Refer to the exhibit. What is the result of executing this python code?
What are two types of FC/FCoE oversubscription ratios? (Choose two.)
An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect. Which backup type must be selected to meet these requirements?
An engineer must perform a backup and restore in Cisco UCS to rebuild the system in a disaster recovery scenario. The backup file must be encrypted to prevent the passwords from being stored as clear text. Which backup configuration meets these requirements?
A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containenzed applications. The operations team requires a solution to orchestrate and optimize the cost of the new solution. Which product must be used to meet these requirements?

Question 71

Report
Export
Collapse

DRAG DROP

Refer to the exhibit. Drag and drop each traffic flow type from the left onto the corresponding number on the right. Not all traffic flow types are used.


Question 71
Correct answer: Question 71

Question 72

Report
Export
Collapse

DRAG DROP

A network engineer is asked to describe the cloud infrastructure models from the perspective of their operation and access to resources. Drag and drop the descriptions from the left onto the appropriate characteristics on the right.


Question 72
Correct answer: Question 72

Question 73

Report
Export
Collapse

An environment consists of a Cisco MDS 9000 Series Switch that uses port channels. An engineer must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows are allowed to use a different link Which load balancing method should be used to accomplish this goal?

A.

src-id/dst-id

A.

src-id/dst-id

Answers
B.

src-dst-oui

B.

src-dst-oui

Answers
C.

src-dst-port

C.

src-dst-port

Answers
D.

src-id/dst-id/oxid

D.

src-id/dst-id/oxid

Answers
Suggested answer: C

Explanation:

The src-dst-port load balancing method ensures that frames in the same flow (identified by the source and destination ports) follow the same links in a port channel. This method is effective in environments with Cisco MDS 9000 Series Switches because it maintains the order of frame delivery within a flow, which is crucial for storage traffic. Subsequent flows can use different links, allowing for efficient utilization of the port channel bandwidth.Reference: Implementing and Operating Cisco Data Center Core Technologies (DCCOR) course materials.

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/6_2/configuration/guides/fabric/nx-os/nx_os_fabric/vsan.html?bookSearch=true

https://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_1_x/1_3/san-os/configuration/guide/PortChnl.pdf

Question 74

Report
Export
Collapse

A customer needs a tool to take advantage of the CI/CD model to streamline its operation and optimize cost. The customer wants to integrate the solution with the cisco products it currently it currently uses, Including Cisco ACI networking and Cisco UCS servers. The solution should also provide on-premises Kubernetes and AppDynamics performance monitoring. Because of the security requirements, the solution not install a local client on products under management. which orchestration solution meets these requirements?

A.

Cisco APIC

A.

Cisco APIC

Answers
B.

CISCO UCS director

B.

CISCO UCS director

Answers
C.

Cisco DCNM

C.

Cisco DCNM

Answers
D.

Cisco CloudCenter

D.

Cisco CloudCenter

Answers
Suggested answer: D

Explanation:

Cisco CloudCenter is the appropriate orchestration solution for the customer's requirements. It supports the CI/CD model, which is essential for streamlining operations and optimizing costs. Cisco CloudCenter can integrate with Cisco ACI networking and Cisco UCS servers, providing a unified management platform. It also offers on-premises Kubernetes support and AppDynamics performance monitoring without the need to install local clients on managed products, aligning with the customer's security requirements.Reference: Cisco CloudCenter documentation and Cisco Data Center Core Technologies study guide.

Question 75

Report
Export
Collapse

Which configuration generates a syslog message when CPU utilization is higher than 60%?

A.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op gt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

A.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op gt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

Answers
B.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op lt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

B.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op lt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

Answers
C.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type next entry-op gt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

C.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type next entry-op gt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

Answers
D.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type next entry-op lt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

D.

event manager applet HIGH-CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type next entry-op lt 60 poll-interval 5 action 1.0 syslog priority notifications msg 'cpu high'

Answers
Suggested answer: A

Explanation:

The correct configuration to generate a syslog message when CPU utilization is higher than 60% is option

A) This configuration uses the Event Manager Applet feature of Cisco IOS to monitor the CPU utilization via SNMP. When the CPU utilization exceeds 60%, the specified action is triggered, which in this case is to send a syslog message with a priority of notifications and the message ''cpu high''. Theevent snmp oidcommand specifies the OID to be monitored, and theentry-op gt 60part of the command sets the condition for triggering the action when the value is greater than 60. Thepoll-interval 5specifies that the SNMP OID will be polled every 5 seconds.

https://www.cisco.com/c/en/us/support/docs/ip/internet-protocol-ip/200931-EEM-Subsystem-in-Order-to-

Monitor-CPU-Tr.pdf

https://blog.ipspace.net/2008/06/generate-snmp-trap-on-high-cpu-load.html

Question 76

Report
Export
Collapse

Host 1 is in VLAN 100 located is DataCenter 1 and Host2 is in VLAN200 located in DataCenter2. Which OTV VLAN mapping configuration allows Layer 2 connectivity between these two hosts?

A.

Option A

A.

Option A

Answers
B.

Option B

B.

Option B

Answers
C.

Option C

C.

Option C

Answers
D.

Option D

D.

Option D

Answers
Suggested answer: C

Explanation:

To allow Layer 2 connectivity between Host 1 in VLAN 100 located in DataCenter 1 and Host 2 in VLAN 200 located in DataCenter 2, the correct OTV VLAN mapping configuration is option C. This configuration involves mapping VLAN 100 to VLAN 200 across the OTV overlay so that hosts in these separate VLANs can communicate as if they were in the same Layer 2 domain. The VLAN mapping is achieved by configuring the OTV edge devices in both data centers to associate the VLANs with each other.

https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/200998-Nexus-7000-OTV-VLAN-Mapping-on-Overlay.html?dtid=osscdc000283

https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/200998-Nexus-7000-OTV-VLAN-Mapping-on-Overlay.html

Question 77

Report
Export
Collapse

A host EPG Client wants to talk to a webserver in EGP Web. A contract with default settings is defined between EPG Client and EPG Web, which allows TCP communication initiated by the client toward the webserver with TCP destination port 80. Which statement is true?

A.

If EPG Web is made a preferred group member, a contract between EPG Client and EPG Web is no longer required for the host in EPG Client to reach the webserver in EPG Web.

A.

If EPG Web is made a preferred group member, a contract between EPG Client and EPG Web is no longer required for the host in EPG Client to reach the webserver in EPG Web.

Answers
B.

If vzAny is configured to consume and provide a 'deny all' contract, traffic between EPG Client and EPG Web is no longer allowed.

B.

If vzAny is configured to consume and provide a 'deny all' contract, traffic between EPG Client and EPG Web is no longer allowed.

Answers
C.

The host in EPG Client is allowed to connect to TCP destination port 80 on the webserver in EPG Web. The webserver will not be allowed to initiate a separate TCP connection to a host port with TCP source port 80.

C.

The host in EPG Client is allowed to connect to TCP destination port 80 on the webserver in EPG Web. The webserver will not be allowed to initiate a separate TCP connection to a host port with TCP source port 80.

Answers
D.

The host in EPG Client is allowed to connect to TCP destination port 80 on the webserver in EPG Web. The webserver is allowed to initiate a separate TCP connection to a host port with TCP source port 80.

D.

The host in EPG Client is allowed to connect to TCP destination port 80 on the webserver in EPG Web. The webserver is allowed to initiate a separate TCP connection to a host port with TCP source port 80.

Answers
Suggested answer: C

Explanation:

The contract between EPG Client and EPG Web allows TCP communication initiated by the client toward the webserver with TCP destination port 80. This means that the host in EPG Client can establish a connection to the webserver in EPG Web on TCP port 80. However, the contract does not allow the webserver to initiate a connection back to the host on the same port, which is typically used for HTTP traffic.

Question 78

Report
Export
Collapse

A network engineer plans to upgrade the firmware of a Cisco UCS B-Series chassis by using the Auto Install feature. Which component is upgraded during the infrastructure firmware upgrade stage?

A.

Cisco IMC

A.

Cisco IMC

Answers
B.

Adapter

B.

Adapter

Answers
C.

I/O module

C.

I/O module

Answers
D.

BIOS

D.

BIOS

Answers
Suggested answer: C

Explanation:

: During the infrastructure firmware upgrade stage using the Auto Install feature, the I/O module is upgraded. The infrastructure firmware upgrade includes updates to the fabric interconnects and I/O modules, which are essential components of the UCS B-Series chassis network connectivity.

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Firmware-Mgmt/4-0/b_UCSM_GUI_Firmware_Management_Guide_4-0/b_UCSM_GUI_Firmware_Management_Guide_4-0_chapter_0100.html

https://www.youtube.com/watch?v=g-4OgYigvRI

Question 79

Report
Export
Collapse

What is required for using puppet in a Cisco NX-OS environment?

A.

Open Agent Container

A.

Open Agent Container

Answers
B.

XML management interface

B.

XML management interface

Answers
C.

NX-API

C.

NX-API

Answers
D.

OpenNP

D.

OpenNP

Answers
Suggested answer: A

Explanation:

Puppet, an open-source configuration management tool, requires the Open Agent Container (OAC) to run on Cisco NX-OS. The OAC provides a contained environment where third-party agents like Puppet can run without affecting the host NX-OS system.

Question 80

Report
Export
Collapse

An engineer is enabling port security on a Cisco MDS 9000 Series Switch. Which feature of enabling port security on a Cisco MDS 9000 Series Switch must be considered?

A.

It always learns about switches that are logging in.

A.

It always learns about switches that are logging in.

Answers
B.

It can be distributed by using Cisco Fabric services.

B.

It can be distributed by using Cisco Fabric services.

Answers
C.

It authorizes only the configured sWWN to participate in the fabric.

C.

It authorizes only the configured sWWN to participate in the fabric.

Answers
D.

It binds the fabric at the switch level.

D.

It binds the fabric at the switch level.

Answers
Suggested answer: C

Explanation:

Port security on Cisco MDS 9000 Series Switches is designed to prevent unauthorized devices from accessing the fabric. When port security is enabled, only the configured sWWN (switch World Wide Name) is authorized to participate in the fabric. This ensures that unauthorized switches or devices cannot log in or access the network, enhancing security within the data center.Reference: Implementing and Operating Cisco Data Center Core Technologies (DCCOR v1.2)

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/6_2/configuration/guides/security/nx-os/sec_cli_6-x/psec.html#92130

Total 491 questions
Go to page: of 50
ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms