ExamGecko
Login
Home / Cisco / 350-401 / List of questions
Ask Question

Cisco 350-401 Practice Test - Questions Answers, Page 60

Add to Whishlist

List of questions

Question 591

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 591 115890 10102024232943000000

Refer to the exhibit. R1 and R2 are directly connected, but the BGP session does not establish. Which action must be taken to build an eBGP session?

Become a Premium Member for full access
  Unlock Premium Member

Question 592

Report Export Collapse

If AP power level is increased from 25 mW to 100 mW. what is the power difference in dBm?

Become a Premium Member for full access
  Unlock Premium Member

Question 593

Report Export Collapse

Which signal strength and noise values meet the minimum SNR for voice networks?

Become a Premium Member for full access
  Unlock Premium Member

Question 594

Report Export Collapse

Which two methods are used by an AP that is typing to discover a wireless LAN controller? (Choose two.)

Become a Premium Member for full access
  Unlock Premium Member

Question 595

Report Export Collapse

SIMULATION

Configure HSRP between DISTRO-SW1 and DISTRO-SW2 on VLAN 100 for hosts connected to ACCESSSW1 to achieve these goals:

Become a Premium Member for full access
  Unlock Premium Member

Question 596

Report Export Collapse

DRAG DROP

Drag and drop the characteristics from the left onto the orchestration tool classifications on the right.


Become a Premium Member for full access
  Unlock Premium Member

Question 597

Report Export Collapse

Which two security features are available when implementing NTP? (Choose two.)

Become a Premium Member for full access
  Unlock Premium Member

Question 598

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 598 115897 10102024232943000000

Hosts PC1 PC2 and PC3 must access resources on Serve 1. An engineer configures NAT on Router R1 1e enable the communication and enters the show command to verify operation Which IP address is used by the hosts when they communicate globally to Server1?

Become a Premium Member for full access
  Unlock Premium Member

Question 599

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 599 115898 10102024232943000000

These commands have been added to the configuration of a switch Which command flags an error if it is added to this configuration?

Become a Premium Member for full access
  Unlock Premium Member

Question 600

Report Export Collapse

Refer to the exhibit.

Cisco 350-401 image Question 600 115899 10102024232943000000

Which GRE tunnel configuration command is missing on R2?

Become a Premium Member for full access
  Unlock Premium Member
Total 983 questions
Go to page: of 99
Open VPLUS File
Convert VPLUS to PDF

Related questions

An engineer must configure a multicast UDP jitter operation. Which configuration should be applied? A) B) C) D)
A customer has recently implemented a new wireless infrastructure using WLC-5520 at a site directly next to a large commercial airport. Users report that they intermittently lose WI-FI connectivity, and troubleshooting reveals it is due to frequent channel changes. Which two actions fix this issue? (Choose two)
An engineer is troubleshooting the Ap join process using DNS. Which FQDN must be resolvable on the network for the access points to successfully register to the WLC?
Reter to the exhibit. Refer to the exhibit. A network engineer must be notified when a user switches to configuration mode. Which script should be applied to receive an SNMP trap and a critical-level log message?
Refer to the exhibit. An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
What are two differences between the RIB and the FIB? (Choose two.)
Refer to the exhibit. What is the result of this Python code?
An engineer must use IP SLA to measure the network performance and record statistics hop-by-hop. Which configuration must be used?
A network engineer must configure the VTY lines on a router to achieve these results: Remote access should be permitted for all feasible protocols. Only a password should be required for device authentication. All idle EXEC sessions must be terminated in 60 minutes. Which configuration should be applied?
Which devices does Cisco DNA Center configure when deploying an IP-based access control policy?