A Cisco IP phone receive untagged data traffic from an attached PC. Which action is taken by the phone?

It allows the traffic to pass through unchanged

It tags the traffic with the default VLAN

It tags the traffic with the native VLAN

Which statement about Link Aggregation when implemented on a Cisco Wireless LAN Controller is true?

One functional physical port is needed to pass client traffic

To pass client traffic two or more ports must be configured.

The EtherChannel must be configured in "mode active"

When enabled the WLC bandwidth drops to 500 Mbps

One functional physical port is needed to pass client traffic

Which set of action satisfy the requirement for multifactor authentication?

The user enters a user name and password, and then clicks a notification in an authentication app on a mobile device

The user swipes a key fob, then clicks through an email link

The user enters a user name and password, and then clicks a notification in an authentication app on a mobile device

The user enters a PIN into an RSA token, and then enters the displayed RSA key on a login screen

The user enters a user name and password and then re-enters the credentials on a second screen

Refer to Exhibit. Which configuration must be applied to the router that configures PAT to translate all addresses in VLAN 200 while allowing devices on VLAN 100 to use their own IP addresses?

Router1(config)#access-list 99 permit 192.168.100.32 0.0.0.31Router1(config)#ip nat inside source list 99 interface gi1/0/0 overloadRouter1(config)#interface gi2/0/1.200Router1(config)#ip nat insideRouter1(config)#interface gi1/0/0Router1(config)#ip nat outside

Router1(config)#access-list 99 permit 192.168.100.0 0.0.0.255Router1(config)#ip nat inside source list 99 interface gi1/0/0 overloadRouter1(config)#interface gi2/0/1.200Router1(config)#ip nat insideRouter1(config)#interface gi1/0/0Router1(config)#ip nat outside

Router1(config)#access-list 99 permit 209.165.201.2 255.255.255.255Router1(config)#ip nat inside source list 99 interface gi1/0/0overload Router1(config)#interface gi2/0/1.200Router1(config)#ip nat insideRouter1(config)#interface gi1/0/0Router1(config)#ip nat outside

Router1(config)#access- list 99 permit 209.165.201.2 0.0.0.0Router1(config)#ip nat inside source list 99 interface gi1/0/0 overloadRouter1(config)#interface gi2/0/1.200Router1(config)#ip nat insideRouter1(config)#interface gi1/0/0Router1(config)#ip nat outside

Which two outcomes are predictable behaviors for HSRP? (Choose two)

The two routers share a virtual IP address that is used as the default gateway for devices on the LAN.

The two routers negotiate one router as the active router and the other as the standby router

The two routers share a virtual IP address that is used as the default gateway for devices on the LAN.

The two routers negotiate one router as the active router and the other as the standby router

Each router has a different IP address both routers act as the default gateway on the LAN, and traffic is load balanced between them.

The two routers synchronize configurations to provide consistent packet forwarding

The two routed share the same IP address, and default gateway traffic is load-balanced between them

How do traditional campus device management and Cisco DNA Center device management differ in regards to deployment?

Cisco DNA Center device management can deploy a network more quickly than traditional campus device management

Traditional campus device management allows a network to scale more quickly than with Cisco DNA Center device management

Cisco DNA Center device management can be implemented at a lower cost than most traditional campus device management options

Traditional campus device management schemes can typically deploy patches and updates more quickly than Cisco DNA Center device management

A corporate office uses four floors in a building• Floor 1 has 24 users• Floor 2 has 29 users• Floor 3 has 28 users•Floor 4 has 22 usersWhich subnet summarizes and gives the most efficient distribution of IP addresses for the router configuration?

l92.168.0.0/25 as summary and 192.168.0.0/27 for each floor

192.168.0.0/26 as summary and 192.168.0.0/29 for each floor

192.168.0.0.24 as summary and 192.168.0.0/28 for each floor

192.168.0.0/23 as summary and 192.168.0.0/25 for each floor

l92.168.0.0/25 as summary and 192.168.0.0/27 for each floor

What are two reasons for an engineer to configure a floating state route? (Choose two)

to automatically route traffic on a secondary path when the primary path goes down

to enable fallback static routing when the dynamic routing protocol fails

to automatically route traffic on a secondary path when the primary path goes down

to route traffic differently based on the source IP of the packet

to enable fallback static routing when the dynamic routing protocol fails

to support load balancing via static routing

to control the return path of traffic that is sent from the router

The service password-encryption command is entered on a router. What is the effect of this configuration?

restricts unauthorized users from viewing clear-text passwords in the running configuration

encrypts the password exchange when a VPN tunnel is established

prevents network administrators from configuring clear-text passwords

protects the VLAN database from unauthorized PC connections on the switch

Refer to me exhibit. Which action is taken by the router when a packet is sourced from 10.10.10.2 and destined for 10.10.10.16?

It uses a route that is similar to the destination address

It floods packets to all learned next hops.

It Queues the packets waiting for the route to be learned.

Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. what is the reason for the problem?

Router2 is using the default hello timer.

The OSPF router IDs are mismatched.

Router2 is using the default hello timer.

The network statement on Router1 is misconfigured.

The OSPF process IDs are mismatched.

Which design element is a best practice when deploying an 802.11b wireless infrastructure?

allocating nonoverlapping channels to access points that are in close physical proximity to one another

disabling TPC so that access points can negotiate signal levels with their attached wireless devices.

setting the maximum data rate to 54 Mbps on the Cisco Wireless LAN Controller

allocating nonoverlapping channels to access points that are in close physical proximity to one another

configuring access points to provide clients with a maximum of 5 Mbps

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command how does the router respond?

It ignores the new static route until the existing OSPF default route is removed

It immediately replaces the existing OSPF route in the routing table with the newly configured static route

It starts load-balancing traffic between the two default routes

It starts sending traffic without a specific matching entry in the routing table to GigabitEthernetO/1

Refer to Exhibit. An engineer is configuring the NEW York router to reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as the primary path. Which two commands must be configured on the New York router so that it can reach the Lo1 interface of the Atlanta router via Washington when the link between New York and Atlanta goes down? (Choose two)

ipv6 router 2000::1/128 2012::1

ipv6 router 2000::1/128 2023::3 5

ipv6 router 2000::1/128 2012::1

ipv6 router 2000::1/128 2012::1 5

ipv6 router 2000::1/128 2012::2

ipv6 router 2000::1/128 2023::2 5

ipv6 router 2000::1/128 2023::3 5

Which statement correctly compares traditional networks and controller-based networks?

Only controller-based networks decouple the control plane and the data plane

Only traditional networks offer a centralized control plane

Only traditional networks natively support centralized management

Traditional and controller-based networks abstract policies from device configurations

Only controller-based networks decouple the control plane and the data plane

How does the dynamically-learned MAC address feature function?

The CAM table is empty until ingress traffic arrives at each port

Switches dynamically learn MAC addresses of each connecting CAM table.

The ports are restricted and learn up to a maximum of 10 dynamically-learned addresses

It requires a minimum number of secure MAC addresses to be filled dynamically

Refer to the exhibit. Which command must be executed for Gi1.1 on SW1 to become a trunk port if Gi1/1 on SW2 is configured in desirable or trunk mode?

switchport mode dynamic desirable

What are two descriptions of three-tier network topologies? (Choose two)

The network core is designed to maintain continuous connectivity when devices fail.

The distribution layer runs Layer 2 and Layer 3 technologies

The core and distribution layers perform the same functions

The access layer manages routing between devices in different domains

The network core is designed to maintain continuous connectivity when devices fail.

The core layer maintains wired connections for each host

The distribution layer runs Layer 2 and Layer 3 technologies

What is a role of access points in an enterprise network?

connect wireless devices to a wired network

support secure user logins to devices or the network

integrate with SNMP in preventing DDoS attacks

serve as a first line of defense in an enterprise network

What is a function of TFTP in network operations?

transfers IOS images from a server to a router for firmware upgrades

transfers a backup configuration file from a server to a switch using a username and password

transfers files between file systems on a router

transfers a configuration files from a server to a router on a congested link

transfers IOS images from a server to a router for firmware upgrades

A network engineer must create a diagram of a multivendor network. Which command must be configured on the Cisco devices so that the topology of the network can be mapped?

Device(Config)#flow-sampler-map topology

What is the same for both copper and fiber interfaces when using SFP modules?

They provide minimal interruption to services by being hot-swappable

They support an inline optical attenuator to enhance signal strength

They provide minimal interruption to services by being hot-swappable

They offer reliable bandwidth up to 100 Mbps in half duplex mode

They accommodate single-mode and multi-mode in a single module

Which protocol does an access point use to draw power from a connected switch?

Internet Group Management Protocol

Adaptive Wireless Path Protocol

Which networking function occurs on the data plane?

forwarding remote client/server traffic

facilitates spanning-tree elections

processing inbound SSH management traffic

sending and receiving OSPF Hello packets

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)

Specify the IP address of the NTP server

Refer to the exhibit. Shortly after SiteA was connected to SiteB over a new single-mode fiber path users at SiteA report intermittent connectivity issues with applications hosted at SiteB What is the cause of the intermittent connectivity issue?

Interface errors are incrementing

An incorrect SFP media type was used at SiteA

High usage is causing high latency

The sites were connected with the wrong cable type

Where does a switch maintain DHCP snooping information?

in the frame forwarding database

Cisco 200-301 Practice Test 11 - Free Online Exam Prep & Questions

Spam

Selling illegal goods, money scams etc.

Hate Speech

Serious attack on a group.

Harassment and bullying

Harassing an individual (including doxing)

Harmful activities

Threatening or glorifying violence or serious harm, including self-harm

Adult content (Consensual)

Nudity/Sexual content

Sexual exploitation and abuse (child safety)

Sexually explicit or suggestive imagery or writing involving minors

Sexual exploitation and abuse (adults and animals)

Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans

Plagiarism

Reusing content without attribution (link and blockquotes)

Poorly written

Not in English or has very bad formatting, grammar, and spelling

Inappropriate credential

Author's credential is offensive, spam, or impersonation

Other

Ex. Illegal content, incomplete question...

Cisco 200-301 Practice Test 11

Question

Cisco 200-301 Practice Tests

Practice Tests