A network administrator is setting up a new IPv6 network using the 64-bit address 2001 0EB8 00C1 2200:0001 0000 0000 0331/64 To simplify the configuration the administrator has decided to compress the address Which IP address must the administrator configure?

ipv6 address 2001 :EB8:C 1:2200.1 ::331-64

ipv6 address 21:EB8:C1:2200:1::331/64

ipv6 address 2001:EB8:C1:22:1::331/64

ipv6 address 2001 :EB8:C 1:2200.1 ::331-64

ipv6 address 2001:EB8:C1:2200:1:0000:331/64

A network engineer is configuring a switch so that it is remotely reachable via SSH The engineer has already configured the host name on the router Which additional command must the engineer configure before entering the command to generate the RSA key?

crypto key generate rsa modulus 1024

ip ssh authentication-retries 2

Refer to the exhibit. Which two commands must be added to update the configuration of router R1 so that it accepts only encrypted connections? (Choose two )

username CNAC secret R!41!4319115@

A network engineer must configure two new subnets using the address block 10 70 128 0/19 to meet these requirements:• The first subnet must support 24 hosts• The second subnet must support 472 hosts• Both subnets must use the longest subnet mask possible from the address block Which two configurations must be used to configure the new subnets and meet a requirement to use the first available address in each subnet for the router interfaces? (Choose two )

interface vlan 1148 ip address 10.70.148.1 255.255.254.0

interface vlan 3002 ip address 10.70.147.17 255.255.255.224

interface vlan 1234 ip address 10.70.159.1 255.255.254.0

interface vlan 1148 ip address 10.70.148.1 255.255.254.0

interface vlan 4722 ip address 10.70.133.17 255.255.255.192

interface vlan 3002 ip address 10.70.147.17 255.255.255.224

interface vlan 155 ip address 10.70.155.65 255.255.255.224

What is a function of Opportunistic Wireless Encryption in an environment?

protect traffic on open networks

increase security by using a WEP connection

protect traffic on open networks

Refer to the exhibit. Which two commands when used together create port channel 10? (Choose two.)

int range g0/0-1 channel-group 10 mode active

int range g0/0-1 channel-group 10 mode passive

int range g0/0-1 channel-group 10 mode active

int range g0/0-1 chanm.l-group 10 mode desirable

int range g0/0-1 channel-group 10 mode passive

int range g0/0-1 channel-group 10 mode auto

int range g0/0-1 channel-group 10 mode on

Refer to the exhibit. A static route must be configured on R14 to forward traffic for the 172 21 34 0/25 network that resides on R86 Which command must be used to fulfill the request?

ip route 172.21.34.0 255.255.255.128 10.73.65.66

ip route 172.21.34.0 255.255.255.192 10.73.65.65

ip route 172.21.34.0 255.255.255.0 10.73.65.65

ip route 172.21.34.0 255.255.128.0 10.73.65.64

ip route 172.21.34.0 255.255.255.128 10.73.65.66

A network engineer must implement an IPv6 configuration on the vlan 2000 interface to create a routable locally-unique unicast address that is blocked from being advertised to the internet. Which configuration must the engineer apply?

interface vlan 2000 ipv6 address fd00::1234:2343/64

interface vlan 2000 ipv6 address ffc0:0000:aaaa::1234:2343/64

interface vlan 2000Ipv6 address fc00:0000:aaaa:a15d:1234:2343:8aca/64

interface vlan 2000 ipv6 address fe80;0000:aaaa::1234:2343/64

interface vlan 2000 ipv6 address fd00::1234:2343/64

Refer to the exhibit. Host A sent a data frame destined for host D What does the switch do when it receives the frame from host A?

It floods the frame out of all ports except port Fa0/1.

It drops the frame from the switch CAM table.

It floods the frame out of all ports except port Fa0/1.

It shuts down the port Fa0/1 and places it in err-disable mode.

It experiences a broadcast storm.

What is the function of the controller in a software-defined network?

multicast replication at the hardware level

fragmenting and reassembling packets

Refer to the exhibit. An engineer built a new L2 LACP EtherChannel between SW1 and SW2 and executed these show commands to verify the work. Which additional task allows the two switches to establish an LACP port channel?

Change the channel-group mode on SW1 to active or passive.

Change the channel-group mode on SW2 to auto

Change the channel-group mode on SW1 to desirable.

Configure the interface port-channel 1 command on both switches.

Change the channel-group mode on SW1 to active or passive.

Refer to the exhibit. Which plan must be Implemented to ensure optimal QoS marking practices on this network?

Trust the IP phone markings on SW1 and mark traffic entering SW2 at SW2.

As traffic traverses MLS1 remark the traffic, but trust all markings at the access layer.

Trust the IP phone markings on SW1 and mark traffic entering SW2 at SW2.

Remark traffic as it traverses R1 and trust all markings at the access layer.

As traffic enters from the access layer on SW1 and SW2. trust all traffic markings.

Refer to the exhibit. Site A was recently connected to site B over a new single-mode fiber path. Users at site A report Intermittent connectivity Issues with applications hosted at site B. What is the reason for the problem?

physical network errors are being transmitted between the two sites.

Heavy usage is causing high latency.

An incorrect type of transceiver has been inserted into a device on the link.

physical network errors are being transmitted between the two sites.

The wrong cable type was used to make the connection.

An engineer must configure R1 for a new user account. The account must meet these requirements:* It must be configured in the local database.* The username is engineer.* It must use the strongest password configurable. Which command must the engineer configure on the router?

R1 (config)# username engineer2 algorithm-type scrypt secret test2021

R1(config)# username engineer2 secret 5 .password S1$b1Ju$kZbBS1Pyh4QzwXyZ

R1(config)# username engineer2 privilege 1 password 7 test2021

R1(config)# username englneer2 secret 4 S1Sb1Ju$kZbBS1Pyh4QzwXyZ

What is a requirement when configuring or removing LAG on a WLC?

The management interface must be reassigned if LAG disabled.

The Incoming and outgoing ports for traffic flow must be specified If LAG Is enabled.

The controller must be rebooted after enabling or reconfiguring LAG.

The management interface must be reassigned if LAG disabled.

Multiple untagged interfaces on the same port must be supported.

Refer to the exhibit. The DHCP server and clients are connected to the same switch. What is the next step to complete the DHCP configuration to allow clients on VLAN 1 to receive addresses from the DHCP server?

Configure the ip dhcp snooping trust command on the interface that is connected to the DHCP server.

Configure the ip dhcp snooping trust command on the interlace that is connected to the DHCP client.

Configure the ip dhcp relay information option command on the interface that is connected to the DHCP client.

Configure the ip dhcp snooping trust command on the interface that is connected to the DHCP server.

Configure the Ip dhcp relay information option command on the interface that is connected to the DHCP server.

Refer to the exhibit. How should the configuration be updated to allow PC1 and PC2 access to the Internet?

Add either the ip nat {inside|outside} command under both interfaces.

Modify the configured number of the second access list.

Add either the ip nat {inside|outside} command under both interfaces.

Remove the overload keyword from the ip nat inside source command.

Change the ip nat inside source command to use interface GigabitEthernet0/0.

Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network.The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?

R1(config)#jp route 172.16.2.2 255.255.255.255 gi0/0

R1(config)#lp route 172.16.2.2 255.255.255.248 gi0/1

R1(config)#jp route 172.16.2.2 255.255.255.255 gi0/0

R1(config>#ip route 172.16.2.0 255.255.255.0 192.168.1.15

R1(conflg)#ip route 172.16.2.0 255.255.255.0 192.168.1.5

Refer to the exhibit. Which command must be issued lo enable a floating static default route on router A?

ip route 0.0.0.0 0.0.0.0 192.168.1.2 10

lp route 0.0.0.0 0.0.0.0 192.168.1.2

ip route 0.0.0.0 0.0.0.0 192.168.2.1 10

ip route 0.0.0.0 0.0.0.0 192.168.1.2 10

Refer to the exhibit. All VLANs are present in the VLAN database. Which command sequence must be applied to complete the configuration?

interface FastEthernet0/1 switchport mode access switchport voice vlan 10

Interface FastEthernet0/1 switchport trunk native vlan 10 switchport trunk allowed vlan 10,15

Interface FastEthernet0/1 switchport mode trunk switchport trunk allowed vlan 10,15

interface FastEthernet0/1 switchport mode access switchport voice vlan 10

Interface FastEthernet0/1 switchport trunk allowed vlan add 10 vlan 10 private-vlan isolated

What is the purpose of the ip address hcp command?

to configure an interface as a DHCP client

to configure an Interface as a DHCP server

to configure an interface as a DHCP helper

to configure an interface as a DHCP relay

to configure an interface as a DHCP client

Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the Internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down.Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?

ip route 0,0.0.0 0.0.0.0 g0/1 6

ip route 0.0.0.0 0.0.0.0 g0/1 1

ip route 0.0.0.0 0.0.0.0 209.165.201.5 10

ip route 0.0.0.0 0.0.0.0 209.165.200.226 1

ip route 0,0.0.0 0.0.0.0 g0/1 6

Refer to the exhibit. Which configuration enables DHCP addressing for hosts connected to interface FastEthernetO/1 on router R4?

interface FastEthernet0/1 ip helper-address 10.0.1.1 ! access-list 100 permit udp host 10.0.1.1 eq bootps host 10.148.2.1

interface FastEthernet0/0 ip helper-address 10.0.1.1 i access-list 100 permit udp host 10.0.1.1 eq bootps host 10.148.2.1

interface FastEthernot0/1 ip helper-address 10.0.1.1 ! access-list 100 permit tcp host 10.0.1.1 eq 67 host 10.148.2.1

interface FastEthernetO/0 ip helper-address 10.0.1.1 I access-list 100 permit host 10.0.1.1 host 10.148.2.1 eq bootps

interface FastEthernet0/1 ip helper-address 10.0.1.1 ! access-list 100 permit udp host 10.0.1.1 eq bootps host 10.148.2.1

OSPF must be configured between routers R1 and R2. Which OSPF configuration must be applied to router R1 to avoid a DR/BDR election?

router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network point-to-point

router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network broadcast

router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf network point-to-point

router ospf 1 network 192.168.1.1 0.0.0.0 area 0 interface e1/1 ip address 192.168.1.1 255.255.255.252 ip ospf cost 0

router ospf 1 network 192.168.1.1 0.0.0.0 area 0 hello interval 15 interface e1/1 Ip address 192.168.1.1 255.255.255.252

What is a function of an endpoint on a network?

allows users to record data and transmit to a tile server

forwards traffic between VLANs on a network

connects server and client devices to a network

allows users to record data and transmit to a tile server

provides wireless services to users in a building

Cisco 200-301 Practice Test 15 - Free Online Exam Prep & Questions

Refer to the exhibit.

Cisco 200-301 image Question 461 109969 10072024004421000000

An engineer is asked to insert the new VLAN into the existing trunk without modifying anything previously configured Which command accomplishes this task?

Become a Premium Member for full access

Unlock Premium Member

Cisco 200-301 Practice Test 15

Question

Cisco 200-301 Practice Tests

Practice Tests