Refer to the exhibit. The network engineer is configuring a new WLAN and is told to use a setup password for authentication instead of the RADIUS servers. Which additional set of tasks must the engineer perform to complete the configuration?

Select WPA2 Policy Disable PMF Enable PSK

Disable PMF Enable PSK Enable 802.1x

Select WPA Policy Enable CCKM Enable PSK

Select WPA Policy Select WPA2 Policy Enable FT PSK

Select WPA2 Policy Disable PMF Enable PSK

Refer to the exhibit. User traffic originating within site 0 is failing to reach an application hosted on IP address 192.168.0.10. Which is located within site A What is determined by the routing table?

The lack of a default route prevents delivery of the traffic

The default gateway for site B is configured incorrectly

The lack of a default route prevents delivery of the traffic

The traffic is blocked by an implicit deny in an ACL on router2

The traffic to 192.168.0.10 requires a static route to be configured in router 1.

Refer to the exhibit An IPv6 address must be obtained automatically on the LAN interface on R1 Which command must be implemented to accomplish the task?

Ipv6 address 2001:dbB:d8d2:1008:4343:61:0010::/64

Refer to the exhibit. Which configuration establishes a Layer 2 LACP EtherChannel when applied to both switches?

Interface range G1/1 – 1/3 switchport mode trunk channel-group 1 mode active no shutdown

Interface range G1/1 – 1/3 switchport mode access channel-group 1 mode passive no shutdown

Interface range G1/1 – 1/3 switchport mode trunk channel-group 1 mode desirable no shutdown

Interface range G1/1 – 1/3 switchport mode access channel-group 1 mode on no shutdown

What must a network administrator consider when deciding whether to configure a new wireless network with APs in autonomous mode or APs running in cloud-based mode?

Autonomous mode APs are less dependent on an underlay but more complex to maintain than APs in cloud-based mode.

Cloud-based mode APs relay on underlays and are more complex to maintain than APs in autonomous mode.

Cloud-based mode APs are easy to deploy but harder to automate than APs in autonomous mode.

Autonomous mode APs are easy to deploy and automate than APs in cloud-based mode.

Under which condition is TCP preferred over UDP?

TCP is used when data reliability is critical, and UDP is used when missing packets are acceptable.

UDP is used when low latency is optimal, and TCP is used when latency is tolerable.

TCP is used when dropped data is more acceptable, and UDP is used when data is accepted outof- order.

TCP is used when data reliability is critical, and UDP is used when missing packets are acceptable.

UDP is used when data is highly interactive, and TCP is used when data is time-sensitive.

Refer to the exhibit. An engineer assigns IP addressing to the current VLAN with three PCs. The configuration must also account for the expansion of 30 additional VLANS using the same Class C subnet for subnetting and host count. Which command set fulfills the request while reserving address space for the expected growth?

Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255 255.255.248

Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 265 255.255.252

Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255 255.255.248

Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255 255.255.0

Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255.255.255.128

When the LAG configuration is updated on a Cisco WLC which additional task must be performed when changes are complete?

Flush all MAC addresses from the WLC

Re-associate the WLC with the access point.

Refer to the exhibit. The image server and client A are running an application that transfers an extremely high volume of data between the two. An engineer is configuring a dedicated circuit between R1 and R2. Which set of commands must the engineer apply to the routers so that only traffic between the image server and client A is forces to use the new circuit?

R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.2R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.1

R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.6R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.5

R1(config)#ip route 10.10.13.10 255.255.255.128 10.10.10.6R2(config)#lp route 192.168.0.100 255.255.255.0 10.10.10.5

R1(config)#ip route 10.10.13.10 255.255.255.252 10.10.10.6R2(config)#tp route 192.168.0.100 255.255.255.252 10.10.10.5

R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.2R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.1

Refer to the exhibit. Clients on the WLAN are required to use 802.11r. What action must be taken to meet the requirement?

Set the Fast Transition option to Enable and enable FT 802.1X under Authentication Key Management.

Under Protected Management Frames, set the PMF option to Required.

Enable CCKM under Authentication Key Management.

Set the Fast Transition option and the WPA gtk-randomize State to disable.

Set the Fast Transition option to Enable and enable FT 802.1X under Authentication Key Management.

What is a characteristic of RSA?

It is a public-key cryptosystem

It uses preshared keys for encryption

It requires both sides to have identical keys

It is a private-key encryption algorithm

It is a public-key cryptosystem

What is the advantage of separating the control plane from the data plane within an SDN network?

decreases overall network complexity

limits data queries to the control plane

offloads the creation of virtual machines to the data plane

Refer to the exhibit. A network engineer must configure NETCONF. After creating the configuration, the engineer gets output from the command show line but not from show running- config. Which command completes the configuration?

Device(config)# netconf max-message 1000

Device(config)# netconf lock-time 500

Device(config)# netconf max-message 1000

Device(config)# no netconf ssh acl 1

Device(config)# netconf max-sessions 100

Refer to Exhibit. Refer to the exhibit. An engineer is building a new Layer 2 LACP EtherChannel between SW1 and SW2. and they executed the given show commands to verify the work Which additional task must be performed so that the switches successfully bundle the second member in the LACP port-channel?

Configure the switchport trunk allowed vlan 300 command on interface Fa0/2 on SW1.

Configure the switchport trunk allowed vlan 300 command on SW1 port-channel 1

Configure the switchport trunk allowed vlan 300 command on interface Fa0/2 on SW1.

Configure the switchport trunk allowtd vlan add 300 command on interface FaO 2 on SW2.

Configure the switchport trunk allowtd vlan add 300 command on SW1 port-channel 1

Refer to the exhibit. The EtherChannel is configured with a speed of 1000 and duplex as full on both ends of channel group 1. What is the next step to configure the channel on switch A to respond to but not initiate LACP communication?

interface port-channel 1 channel-group 1 mode passive

interface range gigabitethernet0/0/0-15 channel-group 1 mode on

interface range gigabitethernet0/0/0-15 channel-group 1 mode desirable

interface port-channel 1 channel-group 1 mode auto

interface port-channel 1 channel-group 1 mode passive

Refer to the exhibit. An engineer is checking the routing table in the main router to identify the path to a server on the network. Which route does the router use to reach the server at 192.168.2.2?

S 192.168.2.0/29 [1/0] via 10.1.1.1

S 192.168.0.0/20 [1/0] via 10.1.1.1

S 192.168.2.0/29 [1/0] via 10.1.1.1

S 192.168.2.0/28 [1/0] via 10.1.1.1

S 192.168.1.0/30 [1/0] via 10.1.1.1

Why would a network administrator choose to implement automation in a network environment?

To simplify the process of maintaining a consistent configuration state across all devices

To centralize device information storage

To implement centralized user account management

To deploy the management plane separately from the rest of the network

Why is a first-hop redundancy protocol implemented?

to protect against default gateway failures

to enable multiple switches to operate as a single unit

to provide load-sharing for a multilink segment

What are two disadvantages of a full-mesh topology? (Choose two.)

It has a high implementation cost.

It requires complex configuration.

It needs a high MTU between sites.

It has a high implementation cost.

It must have point-to-point communication.

It requires complex configuration.

It works only with BGP between sites.

Refer to the exhibit. Routers R1 and R2 are configured with RIP as the dynamic routing protocol. A network engineer must configure R1 with a floating static route to serve as a backup route to network 192.168.23. Which command must the engineer configure on R1?

ip route 192.168.23.0 255.255.255.0 192.168.13.3 121

ip route 192.168.23.0 255.255.255.0 192.168.13.3 100

ip route 192.168.23.0 255.255.255.0 192.168.13.3 121

ip route 192.168.23.0 255.255.255.255 192.168.13.3 121

ip route 192.168.23.0 255.255.255.0 192.168.13.3

How does frame switching function on a switch?

forwards known destinations to the destination port

forwards frames to a neighbor port using CDP

modifies frames that contain a known source VLAN

inspects and drops frames from unknown destinations

forwards known destinations to the destination port

Cisco 200-301 Practice Test 21 - Free Online Exam Questions 801-840

Spam

Selling illegal goods, money scams etc.

Hate Speech

Serious attack on a group.

Harassment and bullying

Harassing an individual (including doxing)

Harmful activities

Threatening or glorifying violence or serious harm, including self-harm

Adult content (Consensual)

Nudity/Sexual content

Sexual exploitation and abuse (child safety)

Sexually explicit or suggestive imagery or writing involving minors

Sexual exploitation and abuse (adults and animals)

Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans

Plagiarism

Reusing content without attribution (link and blockquotes)

Poorly written

Not in English or has very bad formatting, grammar, and spelling

Inappropriate credential

Author's credential is offensive, spam, or impersonation

Other

Ex. Illegal content, incomplete question...

Cisco 200-301 Practice Test 21

Question

Cisco 200-301 Practice Tests

Practice Tests