What does the term 'spirt MAC'' refer to in a wireless architecture?

divides data link layer functions between the AP and WLC

combines the management and control functions from the data-forwarding functions

uses different MAC addresses for 2.4 GHz and 5 GHz bands on the same AP

leverages two APs to handle control and data traffic

Refer to the exhibit. Refer to the exhibit. An engineer executed the script and added commands that were not necessary for SSH and must now remove the commands. Which two commands must be executed to correct the configuration? (Choose two.)

no ip name-server 198.51.100.210

no ip domain name ccna.cisco.com

no ip name-server 198.51.100.210

A network architect planning a new Wi-Fi network must decide between autonomous, cloud-based, and split MAC architectures. Which two facts should the architect consider? (Choose two.)

Lightweight access points are solely used by split MAC architectures.

Autonomous architectures exclusively use tunneling protocols to manage access points remotely.

Lightweight access points are solely used by split MAC architectures.

Cloud-based architectures uniquely use the CAPWAP protocol to communicate between access points and clients.

Each of the three architectures must use WLCs to manage their access points.

All three architectures use access points to manage the wireless devices connected to the wired infrastructure.

Autonomous architectures exclusively use tunneling protocols to manage access points remotely.

Which command creates a static NAT binding for a PC address of 10.1.1.1 to the public routable address 209.165.200.225 assigned to the PC?

R1(config)#ip nat inside source static 10.1.1.1 209.165.200.225

R1(config)#ip nat inside source static 209.165.200.225 10.1.1.1

R1(config)#ip nat outside source static 10.1.1.1 209.165.200.225

R1(config)#ip nat outside source static 209.165.200.225 10.1.1.1

Which selections must be used on the WLC when implementing a RADIUS server for wireless authentication?

802.1x and the MAC address of the server

Network Access Control State and SSH

AAA Override and the IP address of the server

What is an Ansible inventory?

collection of actions to perform on target devices, expressed in YAML format

file that defines the target devices upon which commands and tasks are executed

unit of Python code to be executed within Ansible

collection of actions to perform on target devices, expressed in YAML format

device with Ansible installed that manages target devices

Refer to the exhibit. Refer to the exhibit. The My_WLAN wireless LAN was configured with WPA2 Layer 2 PSK security. Which additional configuration must the administrator perform to allow users to connect to this WKAN on a different subnet called Data?

Enable Status and select data from the Interface/Interface Group drop-down list.

Enable Broadcast SSID and select data from the Interface/Interface Group drop-down list.

Enable Status and select data from the Interface/Interface Group drop-down list.

Enable Status and set the NAS-ID to data.

Enable Status and enable Broadcast SSID.

What is the role of syslog level 7 in network device health monitoring?

It sends outputs from various debug commands on the device.

It provides information about error conditions visible on the network device.

It shares normal operational messages from the network equipment.

It sends outputs from various debug commands on the device.

It warns about emergency conditions on the network appliance.

Refer to the exhibit. Refer to the exhibit. A network engineer started to change default settings on SW1 to allow remote access and has entered the following in the configuration mode:SW1(config)#line vty 0 15SW1(config-line)#password Labtest32!Which set of commands are needed to allow only SSH access and hide passwords in the running configuration?

SW1(config-line)#transport input sshSW1(config-line)#exitSW1(config)#service password-encryption

SW1(config-line)#exitSW1(config)#aaa new-model

SW1(config-line)#login localSW1(config-line)#exitSW1(config)#enable secret test!2E

SW1(config-line)#transport input sshSW1(config-line)#exitSW1(config)#service password-encryption

SW1(config-line)#login localSW1(config-line)#exitSW1(config)#crypto key generate rsa

How does network automation help reduce network downtime?

Configuration templates and testing can be built into implementation, which increases the success rate of a network change.

Changes can be implemented in parallel across multiple devices at once, which increases the speed of the change rate.

By using automation platforms with intent-based configuration, all changes are checked for possible outages before being implemented.

Emails can be generated based on when a network admin performs a network change, which increases visibility.

Configuration templates and testing can be built into implementation, which increases the success rate of a network change.

What are two benefits for using private IPv4 addressing? (Choose two.)

They alleviate the shortage of public IPv4 addresses.

They provide a layer of security from Internet threats.

They alleviate the shortage of public IPv4 addresses.

They supply redundancy in the case of failure.

They offer Internet connectivity to endpoints on private networks.

They allow for Internet access from IoT devices.

They provide a layer of security from Internet threats.

What are two benefits for using private IPv4 addressing? (Choose two.)

They alleviate the shortage of public IPv4 addresses.

They provide a layer of security from Internet threats.

They alleviate the shortage of public IPv4 addresses.

They supply redundancy in the case of failure.

They offer Internet connectivity to endpoints on private networks.

They allow for Internet access from IoT devices.

They provide a layer of security from Internet threats.

Refer to the exhibit. Refer to the exhibit. Company A wants to use a RADIUS server to service all user and device authentication attempts with a more secure and granular authentication approach. Not all client devices support dot1x authentication. Which two configuration changes must be made to accomplish the task? (Choose two.)

Select Authentication server under the AAA servers tab.

Configure Enterprise Security type under the Layer 2 tab.

Enable AutoConfig IPSK under the Layer 2 tab.

Select Authentication server under the AAA servers tab.

Configure Enterprise Security type under the Layer 2 tab.

Set Authentication under the Layer 3 tab.

Enable WPA2 Policy under the Layer 2 tab.

What is the difference between SNMP traps and SNMP polling?

SNMP traps send periodic updates via the MIB, and SNMP polling sends data on demand.

SNMP traps are used for proactive monitoring, and SNMP polling is used for reactive monitoring.

SNMP traps send periodic updates via the MIB, and SNMP polling sends data on demand.

SNMP traps are initiated by the network management system, and network devices initiate SNMP polling.

SNMP traps are initiated using a push model at the network device, and SNMP polling is initiated at the server.

Cisco 200-301 Practice Test 26 - Free Online Exam Prep & Questions

Why is UDP more suitable than TCP tor applications that require low latency, such as VoIP?

Become a Premium Member for full access

Unlock Premium Member

Cisco 200-301 Practice Test 26

Question

Cisco 200-301 Practice Tests

Practice Tests