Refer to the exhibit. An engineer is configuring an EtherChannel using LACP between Switches 1 and 2 Which configuration must be applied so that only Switch 1 sends LACP initiation packets?

Switch1{config-if)£channel-group 1 mode activeSwitch2(config-if)#channel-group 1 mode passive

Switch 1 (config-if)#channel-group 1 mode onSwrtch2(config-if)#channel-group 1 mode passive

Switch1(config-if)#channel-group 1 mode passiveSwitch2(config-if)#channel-group 1 mode active

Switch1{config-if)£channel-group 1 mode activeSwitch2(config-if)#channel-group 1 mode passive

Switch1(config-if)#channel-group 1 mode onSwitch2(config-if)#channel-group 1 mode active

Refer to the exhibit. R1 learns all routes via OSPF Which command configures a backup static route on R1 to reach the 192 168.20.0/24 network via R3?

R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 111

R1(config)#ip route 192.168.20.0 255.255.0.0 192.168.30.2

R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 90

R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 111

R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2

What is the difference between IPv6 unicast and anycast addressing?

An individual IPv6 unicast address is supported on a single interface on one node but an IPv6 anycast address is assigned to a group of interfaces on multiple nodes.

IPv6 anycast nodes must be explicitly configured to recognize the anycast address, but IPv6 unicast nodes require no special configuration

IPv6 unicast nodes must be explicitly configured to recognize the unicast address, but IPv6 anycast nodes require no special configuration

An individual IPv6 unicast address is supported on a single interface on one node but an IPv6 anycast address is assigned to a group of interfaces on multiple nodes.

Unlike an IPv6 anycast address, an IPv6 unicast address is assigned to a group of interfaces on multiple nodes

How does Rapid PVST+ create a fast loop-free network topology?

It generates one spanning-tree instance for each VLAN

lt requires multiple links between core switches

It generates one spanning-tree instance for each VLAN

It maps multiple VLANs into the same spanning-tree instance

It uses multiple active paths between end stations.

Refer to the exhibit. The link between PC1 and the switch is up. but it is performing poorly. Which interface condition is causing the performance problem?

There is a duplex mismatch on the interface

There is an issue with the fiber on the switch interface.

There is a speed mismatch on the interface.

There is an interface type mismatch

What is an expected outcome when network management automation is deployed?

Software upgrades are performed from a central controller

A distributed management plane must be used.

Software upgrades are performed from a central controller

Complexity increases when new device configurations are added

Custom applications are needed to configure network devices

Refer to the exhibit. Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?

Configure the router A interfaces with the highest OSPF priority value within the area.

Configure the OSPF priority on router A with the lowest value between the three routers.

Configure router B and router C as OSPF neighbors of router A.

Configure the router A interfaces with the highest OSPF priority value within the area.

Configure router A with a fixed OSPF router ID

Which two components comprise part of a PKI? (Choose two.)

preshared key that authenticates connections

clear-text password that authenticates connections

What are two benefits of FHRPs? (Choose two.)

They enable automatic failover of the default gateway.

They allow multiple devices to serve as a single virtual gateway for clients in the network.

They enable automatic failover of the default gateway.

They allow multiple devices to serve as a single virtual gateway for clients in the network.

They are able to bundle multiple ports to increase bandwidth.

They prevent loops in the Layer 2 network.

Refer to the exhibit. Which command configures OSPF on the point-to-point link between routers R1 and R2?

network 10.0.0.0 0.0.0.255 area 0

What causes a port to be placed in the err-disabled state?

shutdown command issued on the port

Refer to the exhibit. An engineer is configuring a new router on the network and applied this configuration. Which additional configuration allows the PC to obtain its IP address from a DHCP server?

Configure the ip helper-address 172.16.2.2 command under interface Gi0/0

Configure the ip dhcp relay information command under interface Gi0/1.

Configure the ip dhcp smart-relay command globally on the router

Configure the ip helper-address 172.16.2.2 command under interface Gi0/0

Configure the ip address dhcp command under interface Gi0/0

Refer to the exhibit. The following must be considered:• SW1 is fully configured for all traffic• The SW4 and SW9 links to SW1 have been configured• The SW4 interface Gi0/1 and Gi0/0 on SW9 have been configured• The remaining switches have had all VLANs added to their VLAN databaseWhich configuration establishes a successful ping from PC2 to PC7 without interruption to traffic flow between other PCs?

SW4interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14SW11#interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14SW9#interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 108

SW4interface Gi0/7 switchport mode trunk switchport trunk allowed vlan 108!interface Gi/0/2 switchport mode access switchport access vlan 14SW11#interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108!interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14,108SW9#interface Gi0/2 switchport mode access switchport access vlan 14

SW4interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108SW11#interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108!!interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14,108SW9#interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14

SW4interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14SW11#interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14SW9#interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 108

SW4interface Gi/0/2 switchport mode access switchport access vlan 14SW11#interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14!interface Gi0/0 switchport mode access switchport access vlan 14!interface Gi0/1 switchport mode trunkSW9#interface Gi0/2 switchport mode access switchport access vlan 14

Which two network actions occur within the data plane? (Choose two.)

Add or remove an 802.1Q trunking header.

Match the destination MAC address to the MAC address table.

Add or remove an 802.1Q trunking header.

Make a configuration change from an incoming NETCONF RPC.

Match the destination MAC address to the MAC address table.

Reply to an incoming ICMP echo request.

Which QoS traffic handling technique retains excess packets in a queue and reschedules these packets for later transmission when the configured maximum bandwidth has been surpassed?

weighted random early detection

Refer to the exhibit. All traffic enters the CPE router from interface Serial0/3 with an IP address of 192 168 50 1 Web traffic from the WAN is destined for a LAN network where servers are load-balanced An IP packet with a destination address of the HTTP virtual IP of 192 1681 250 must be forwarded Which routing table entry does the router use?

192.168.1.224/27 via 192.168.15.5

192.168.1.0/24 via 192.168.12.2

192.168.1.128/25 via 192.168.13.3

192.168.1.192/26 via 192.168.14.4

192.168.1.224/27 via 192.168.15.5

Refer to the exhibit. Which two commands must be configured on router R1 to enable the router to accept secure remote-access connections? (Choose two )

username cisco password 0 Cisco

Refer to the exhibit. An engineer assumes a configuration task from a peer Router A must establish an OSPF neighbor relationship with neighbor 172 1 1 1 The output displays the status of the adjacency after 2 hours.What is the next step in the configuration process for the routers to establish an adjacency?

Configure router A to use the same MTU size as router B.

Set the router B OSPF ID to a nonhost address.

Configure a point-to-point link between router A and router B.

Set the router B OSPF ID to the same value as its IP address

Refer to the exhibit. Routers R1 and R3 have the default configuration The router R2 priority is set to 99 Which commands on R3 configure it as the DR in the 10.0 4.0/24 network?

R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100

R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100

R3(config)#interface Gig0/0 R3(config-if)i=ip ospf priority 1

R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0

Refer to the exhibit. A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when the primary link goes down. Which primary route configuration must be used?

ip route 0.0.0.0 0.0.0.0 192.168.0.2

ip route 0.0.0.0 0.0.0.0 192.168.0.2 GigabitEthernetl/0

ip route 0.0.0.0 0.0.0.0 192.168.0.2 tracked

ip route 0.0.0.0 0.0.0.0 192.168.0.2 floating

ip route 0.0.0.0 0.0.0.0 192.168.0.2

What is one reason to implement LAG on a Cisco WLC?

to provide link redundancy and load balancing

to increase security and encrypt management frames

to provide link redundancy and load balancing

to allow for stateful and link-state failover

to enable connected switch ports to failover and use different VLANs

Which action implements physical access control as part of the security program of an organization?

setting up IP cameras to monitor key infrastructure

configuring a password for the console port

backing up syslogs at a remote location

configuring enable passwords on network devices

setting up IP cameras to monitor key infrastructure

Cisco 200-301 Practice Test 14 - Free Online Exam Prep & Questions

Refer to the exhibit.

Cisco 200-301 image Question 421 109929 10072024004421000000

Users on existing VLAN 100 can reach sites on the Internet. Which action must the administrator take to establish connectivity to the Internet for users in VLAN 200?

Become a Premium Member for full access

Unlock Premium Member

Cisco 200-301 Practice Test 14

Question

Cisco 200-301 Practice Tests

Practice Tests